SECO-LARM SD-6176-SSQ Outdoor Piezoelectric Request Exit Pushbuttons Instruction Manual

: June 16, 2024
: SECO-LARM

SECO-LARM SD-6176-SSQ Outdoor Piezoelectric Request Exit Pushbuttons

Product Information

The ENFORCER Outdoor Piezoelectric Request to Exit Pushbutton is a durable and versatile push button designed for both indoor and outdoor use. It is IP65 rated, ensuring protection against dust and water ingress. The push button features a piezoelectric mechanism, which generates a small electrical charge when pressed. It has an LED ring around the button that changes color from green to red or red to green when the button is pressed. The push button offers timed or toggle output options.
The push button includes a separate manual override button in case power to the piezoelectric push button fails. This ensures that the exit function can still be activated even in the event of a power failure. The relay of the push button is rated at 2A@30VDC and has two individually programmable outputs (NO/NC).
The push button is constructed with a stainless steel plate, making it durable and resistant to corrosion. It weighs approximately 3.5-oz (99g) for the slimline single-gang plate, 4-oz (113g) for the single-gang plate with manual override, 2.6-oz (74g) for the slimline plate, and 3.1-oz (88g) for the slimline plate with manual override.

Specifications

Operating voltage: 12~24 VDC
Current drain:
- Standby: 100mA@12VDC
- Active: N/A
Contact rating:
- Ring LED switch: 2A@30VDC or 0.5A@125VAC
Ring LED Colors: Red, Green
Output time: 1~30 seconds (timed), Toggle
IP rating: IP65
Operating temperature: 32 ~158 F (0 ~70 C)
Plate material: Stainless steel
Weight:
- Slimline: 2.6-oz (74g)
- Slimline with Manual Override: 3.1-oz (88g)
- Single-Gang: 3.5-oz (99g)
- Single-Gang with Manual Override: 4-oz (113g)

Parts List

Piezoelectric push button: 1 x
Wires for manual override: 2 x
Mounting screws: 2 x
Manual: 1 x

Installation

Prepare wiring to provide 12~24 VDC power and connect devices to the relay outputs.
Note: The device includes one relay with two outputs. Outputs trigger simultaneously but can be configured independently. To set the output modes, see Relay Output Modes on page 3.
Remove the plastic cover from the rear of the switch and carefully pierce the rubber grommet.
For SD-6176-SSVQ and SD-6276-SSVQ models, wire the manual override button.
- Wiring For N.O.:
  Connect the two wires between the NO and COM terminals of the override button and the Output 1 or 2 terminals on the switch.
- Wiring For N.C.:
  Connect the two wires between the NC and COM terminals of the override button and the Output 1 or 2 terminals on the switch.
Wire the switch according to the provided diagram.
Connect (-) and (+) to a 12~24 VDC power source.
Connect other devices to Outputs 1 or 2.
Replace the plastic switch cover and screw the plate onto the mounting surface.

Frequently Asked Questions (FAQ)

What is the IP rating of the push button?
The push button is IP65 rated, making it suitable for outdoor use as it provides protection against dust and water ingress.
What is the purpose of the manual override button?
The manual override button is included as a backup solution in case power to the piezoelectric push button fails. It allows the user to activate the exit function even in the event of a power failure.
How many outputs does the relay have?
The relay of the push button has two individually programmable outputs (NO/NC).
What is the weight of the push button?
The weight of the push button varies depending on the model:
- Slimline: 2.6-oz (74g)
- Slimline with Manual Override: 3.1-oz (88g)
- Single-Gang : 3.5-oz (99g)
- Single-Gang with Manual Override: 4-oz (113g)

ABOUT PRODUCT

Piezoelectric push buttons for indoor or outdoor use (IP65).
LED ring around button changes from green to red or red to green when the button is pressed.
Timed or toggle output.
Includes separate manual override button in case power to piezoelectric push button fails.
Relay rated 2A@30VDC with two individually programmable outputs (NO/NC).

Specifications

Operating voltage: 12~24 VDC
Current drain:
- Standby: 100mA@12VDC
- Active: N/A
Contact rating:
- Ring LED switch: 2A@30VDC or 0.5A@125VAC
Ring LED Colors: Red, Green
Output time: 1~30 seconds (timed), Toggle
IP rating: IP65
Operating temperature: 32 ~158 F (0 ~70 C)
Plate material: Stainless steel
Weight:
- Slimline: 2.6-oz (74g)
- Slimline with Manual Override: 3.1-oz (88g)
- Single-Gang: 3.5-oz (99g)
- Single-Gang with Manual Override: 4-oz (113g)

Parts List

Piezoelectric push button 1 x
Mounting screws 2 x
Wires for manual override 1 2 x
Manual 1 x

Overview

SD-6176-SSVQ and SD-6276-SSVQ with Manual Override button shown, other models similar.

SECO-LARM-SD-6176-SSQ-Outdoor-Piezoelectric-Request-Exit-Pushbuttons-
FIG-2

Installation

Prepare wiring to provide 12~24 VDC power and connect devices to the relay outputs.
Note: The device includes one relay with two outputs. Outputs trigger simultaneously but can be configured independently. To set the output modes, see Relay Output Modes on page 3.
Remove the plastic cover from the rear of the switch and carefully pierce the rubber grommet.
SD-6176-SSVQ and SD-6276-SSVQ: Wire the manual override button. See page 3.
Wire the switch according to the diagram on the right. Connect (-) and (+) to a 12~24 VDC power source. Connect other devices to Outputs 1 or 2.
Replace the plastic switch cover and screw the plate onto the mounting surface.
1 SD-6176-SSVQ and SD-6276-SSVQ only.

Wiring the Manual Override

SD-6176-SSVQ and SD-6276-SSVQ Only
Connect the manual override button with the included wires.

Wiring For N.O.:
Connect the two wires between the NO and COM terminals of the override button and the Output 1 or 2 terminals on the switch.
Wiring For N.C.:
Connect the two wires between the NC and COM terminals of the override button and the Output 1 or 2 terminals on the switch.

Notes

Remove the thin panel on the bottom of the plastic cover to allow wiring to pass through.
There is only one relay, wiring the button to either output will allow the other output to trigger simultaneously.
Do not connect the manual override button to more than one output.
When wiring for either N.O. or N.C., be sure to also set the Relay Output Mode to N.O., as described below. If Relay Output Mode and override button wiring do not match, the product may not function as expected.

Configuring the Pushbutton

Buzzer Output
Use the buzzer output jumper JP3 to program the buzzer output. Placing the jumper on the left turns buzzer output ON. Placing the jumper on the right turns buzzer output OFF.
Relay Output Mode
- Outputs 1 and 2 can be set independently using jumpers JP1 and JP2. Note: Both outputs trigger simultaneously.
- Place the jumper on the right for N.O. operation and on the left for N.C. operation.
LED Ring Colors
- ON: LED is green while in standby, and turns red when triggered.
- OFF: LED is red while in standby, and turns green when triggered.
Switch Output Type
- TIMER: When set to TIMER, pressing the switch will trigger the relay for the set time. Set the time using the trimpot as described above.
- TOGGLE: When set to TOGGLE, pressing the switch will cause the relay to trigger until the switch is pressed again.
Timer Adjustment
- Output duration is adjustable 1~30 seconds. (Must be set to ‘Timer’ in step 4)
- Gently rotate the trimpot using a Philips head screwdriver. Counterclockwise decreases the output time.
- Clockwise increases the output time.

Sample Installation

Electromagnetic Lock (Fail-Safe) with Strobe Light

SECO-LARM-SD-6176-SSQ-Outdoor-Piezoelectric-Request-Exit-Pushbuttons-
FIG-12

Also Available from SECO-LARM

SECO-LARM-SD-6176-SSQ-Outdoor-Piezoelectric-Request-Exit-Pushbuttons-
FIG-13

WARRANTY

This SECO-LARM product is warranted against defects in material and workmanship while used in normal service for a period of one (1) year from the date of sale to the original consumer customer. SECO-LARM’s obligation is limited to the repair or replacement of any defective part if the unit is returned, transportation prepaid, to SECO-LARM. This Warranty is void if damage is caused by or attributed to acts of God, physical or electrical misuse or abuse, neglect, repair, or alteration, improper or abnormal usage, or faulty installation, or if for any other reason SECO-LARM determines that such equipment is not operating properly as a result of causes other than defects in material and workmanship. The sole obligation of SECO-LARM, and the purchaser’s exclusive remedy, shall be limited to replacement or repair only, at SECO-LARM’s option. In no event shall SECO-LARM be liable for any special, collateral, incidental, or consequential personal or property damages of any kind to the purchaser or anyone else.

NOTICE
The information and specifications printed in this manual are current at the time of publication. However, the SECO-LARM policy is one of continual development and improvement. For this reason, SECO-LARM reserves the right to change specifications without notice. SECO-LARM is also not responsible for misprints or typographical errors.
Copyright © 2011 SECO-LARM U.S.A., Inc. All rights reserved. This material may not be reproduced or copied, in whole or in part, without the written permission of SECO-LARM.