PolyVision PJ905 Projector User Guide

June 16, 2024
PolyVision

PJ905 Projector

Product Information: FOCUS PJ905 Projector

Specifications

  • Model: FOCUS PJ905
  • Projector Type: DLP
  • Resolution: HD (1280 x 720)
  • Lamp Type: Mercury-containing lamp(s)

Main Features

The FOCUS PJ905 projector is a high-definition DLP projector
designed for home and office use. It offers the following main
features:

  • HD resolution for sharp and clear image quality

  • Compact and portable design for easy setup and
    transportation

  • Built-in HDMI interface for seamless connectivity with various
    devices

  • User-friendly OSD menus for easy navigation and settings
    adjustment

  • Energy-saving mode to reduce power consumption

Important Safety Information

It is essential to read and understand the following safety
instructions before using the FOCUS PJ905 projector:

  • Warning: This symbol alerts you to situations
    that may damage the unit, create a hazardous environment, or cause
    personal injury.

  • Caution: This symbol alerts you to situations
    that may damage the unit.

  • Important: This symbol provides additional
    information that should not be overlooked.

  • Note: This symbol provides additional
    information on the topic at hand.

General Safety Information

Follow these general safety guidelines to ensure safe usage of
the FOCUS PJ905 projector:

  • Do not expose the projector to water or moisture.

  • Avoid placing the projector near heat sources or in direct
    sunlight.

  • Use only the provided power cord and do not overload power
    outlets.

  • Keep the projector away from children and pets.

Regulatory Warnings

Prior to installation and usage of the projector, it is
important to read the regulatory notices in the Regulatory
Compliance section on page 55 of the user manual.

Recycle Instructions

The FOCUS PJ905 projector contains mercury in its lamp(s) and
may also contain other electronic waste. It is crucial to recycle
or dispose of the product in accordance with local, state, or
federal laws. For more information, contact the Electronic
Industries Alliance at www.eiae.org. For lamp-specific disposal
information, visit www.lamprecycle.org.

About this Manual

The user manual is intended for end users and provides
instructions on how to install and operate the FOCUS PJ905
projector. The manual is designed in a printer-friendly format to
save paper and protect the environment. It is recommended to only
print relevant sections based on your needs.

FAQ (Frequently Asked Questions)

  1. 1.  **Q: How do I connect my device to the  

    projector?**

A: To connect your device to the FOCUS PJ905 projector, follow
these steps:

  1. 1.       1. Ensure both the projector and your device are powered off.
    1. Connect one end of an HDMI cable to the HDMI port on your
      device.

    2. Connect the other end of the HDMI cable to the HDMI input port
      on the projector.

    3. Power on both the projector and your device.

    4. Select the HDMI input source on the projector using the OSD
      menu or remote control.

  2. Q: How do I adjust the image settings?

A: To adjust the image settings on the FOCUS PJ905 projector,
use the following steps:

  1. 1.       1. Press the Menu button on the remote control to open the Main  

    menu.

    1. Navigate to the Image or Picture settings using the arrow
      keys.

    2. Adjust settings such as brightness, contrast, color
      temperature, and sharpness according to your preference.

    3. Press the Menu button again to exit the menu and apply the
      changes.

  2. Q: How do I clean the projector lens?

A: To clean the lens of the FOCUS PJ905 projector, follow these
steps:

  1. 1. Turn off the projector and unplug it from power.
  2. Gently wipe the lens surface with a soft, lint-free cloth.

  3. If necessary, moisten the cloth with a small amount of lens
    cleaning solution or water.

  4. Avoid using abrasive materials or excessive force that may
    scratch the lens.

  5. Allow the lens to dry completely before reconnecting and
    powering on the projector.

FOCUS

PJ905 Projector
User Guide

Search

Copyright
This publication, including all photographs, illustrations and software, is protected under international copyright laws, with all rights reserved. Neither this manual, nor any of the material contained herein, may be reproduced without written consent of the author. © Copyright 2010
Disclaimer
The information in this document is subject to change without notice. The manufacturer makes no representations or warranties with respect to the contents hereof and specifically disclaims any implied warranties of merchantability or fitness for any particular purpose. The manufacturer reserves the right to revise this publication and to make changes from time to time in the content hereof without obligation of the manufacturer to notify any person of such revision or changes.
Trademark Recognition
Kensington is a U.S. registered trademark of ACCO Brand Corporation with issued registrations and pending applications in other countries throughout the world. HDMI, the HDMI Logo, and High-Definition Multimedia Interface are trademarks or registered trademarks of HDMI Licensing LLC in the United States and other countries. All other product names used in this manual are the properties of their respective owners and are acknowledged.
Part Number ­ 3534147300 revA
— i —

Search

DDLLPP PPrroojjeeccttoorr—-UUsseerr”ss MMaannuuaall
Important Safety Information
Important: It is strongly recommended that you read this section carefully before using the projector. These safety and usage instructions will ensure that you enjoy many years of safe use of the projector. Keep this manual for future reference. Symbols Used Warning symbols are used on the unit and in this manual to alert you of hazardous situations. The following styles are used in this manual to alert you to important information. Note: Provides additional information on the topic at hand.
Important: Provides additional information that should not be overlooked.
Caution: Alerts you to situations that may damage the unit.
Warning: Alerts you to situations that may damage the unit, create a hazardous environment, or cause personal injury. Throughout this manual, component parts and items in the OSD menus are denoted in bold font as in this example: “Push the Menu button on the remote control to open the Main menu.” General Safety Information
¾ Do not open the unit case. Aside from the projection lamp, there are no user-serviceable parts in the unit. For servicing, contact qualified service personnel.
¾ Follow all warnings and cautions in this manual and on the unit case. ¾ The projection lamp is extremely bright by design. To avoid damage to eyes, do not look into the
lens when the lamp is on. ¾ Do not place the unit on an unstable surface, cart, or stand. ¾ Avoid using the system near water, in direct sunlight, or near a heating device. ¾ Do not place heavy objects such as books or bags on the unit.
— ii —

Search

PPrreeffaaccee
Projector Installation Notice Note: PolyVision recommends only using projector with mounting solution that was shipped with the projector. These instructions are important but should not be relevant to your total solution. ¾ Place the projector in a horizontal position The tilt angle of the projector should not exceed 15 degrees, nor should the projector be installed in any way other than the desktop and ceiling mount, otherwise lamp life could decrease dramatically.
¾ Allow at least 50 cm clearance around the exhaust vent.
¾ Ensure that the intake vents do not recycle hot air from the exhaust vent. ¾ When operating the projector in an enclosed space, ensure that the surrounding air temperature
within the enclosure does not exceed 5 ­ 35°C while the projector is running, and the air intake and exhaust vents are unobstructed. ¾ All enclosures should pass a certified thermal evaluation to ensure that the projector does not recycle exhaust air, as this may cause the device to shutdown even if the enclosure temperature is with the acceptable 5 ­ 35°C range.
­ iii ­

Search

DDLLPP PPrroojjeeccttoorr—-UUsseerr”ss MMaannuuaall
Power Safety ¾ Only use the supplied power cord. ¾ Do not place anything on the power cord. Place the power cord where it will not be in the way of foot traffic. ¾ Remove the batteries from the remote control when storing or not in use for a prolonged period.
Replacing the Lamp Replacing the lamp can be hazardous if done incorrectly. See Replacing the Projection Lamp on page 40 for clear and safe instructions for this procedure. Before replacing the lamp: ¾ Unplug the power cord. ¾ Allow the lamp to cool for about one hour.
Cleaning the Projector ¾ Unplug the power cord before cleaning. See Cleaning the Projector on page 43. ¾ Allow the lamp to cool for about one hour.
Regulatory Warnings Before installing and using the projector, read the regulatory notices in the Regulatory Compliance section on page 55.
Important Recycle Instructions:
Hg
Lamp(s) inside this product contain mercury. This product may contain other electronic waste that can be hazardous if not disposed of properly. Recycle or dispose in accordance with local, state, or federal Laws. For more information, contact the Electronic Industries Alliance at WWW.EIAE.ORG. For lamp specific disposal information check WWW.LAMPRECYCLE.ORG. Symbol Explanations
DISPOSAL: Do not use household or municipal waste collection services for disposal of electrical and electronic equipment. EU countries require the use of separate recycling collection services.
— iv —

Search

PPrreeffaaccee Main Features
· Lightweight unit, easy to pack away and transport. · Compatible with all major video standards including NTSC, PAL, and SECAM. · A high brightness rating allows for presentations in daylight or in lit rooms. · Supports resolutions up to SXGA+ at 16.7 million colors to deliver crisp, clear images. · Flexible setup allows for front, rear projections. · Line-of-vision projections remain square, with advanced keystone correction for angled
projections. · Input source automatically detected.
About this manual
This manual is intended for end users and describes how to install and operate the DLP projector. Wherever possible, relevant information–such as an illustration and its description–has been kept on one page. This printer- friendly format is both for your convenience and to help save paper, thereby protecting the environment. It is suggested that you only print sections that are relevant to your needs.
­ v ­

Search

DDLLPP PPrroojjeeccttoorr—-UUsseerr”ss MMaannuuaall
Table of Contents
GETTING STARTED ………………………………………………………………………………………………………………………………………. 1
PACKING CHECKLIST ……………………………………………………………………………………………………………………………………….. 1 VIEWS OF PROJECTOR PARTS…………………………………………………………………………………………………………………………….. 2
Front-right View …………………………………………………………………………………………………………………………………………. 2 Top view–On-screen Display (OSD) buttons and LEDs ………………………………………………………………………………….. 3 Rear view …………………………………………………………………………………………………………………………………………………… 4 Bottom view………………………………………………………………………………………………………………………………………………… 5 REMOTE CONTROL PARTS ………………………………………………………………………………………………………………………………… 6 REMOTE CONTROL OPERATING RANGE………………………………………………………………………………………………………………. 8 PROJECTOR AND REMOTE CONTROL BUTTONS…………………………………………………………………………………………………….. 8
SETUP AND OPERATION………………………………………………………………………………………………………………………………. 9
INSERTING THE REMOTE CONTROL BATTERIES ……………………………………………………………………………………………………. 9 CONNECTING INPUT DEVICES ………………………………………………………………………………………………………………………….. 10 STARTING AND SHUTTING DOWN THE PROJECTOR………………………………………………………………………………………………. 11 SETTING AN ACCESS PASSWORD (SECURITY LOCK) ……………………………………………………………………………………………. 13 ADJUSTING THE PROJECTOR LEVEL ………………………………………………………………………………………………………………….. 15 ADJUSTING THE FOCUS AND KEYSTONE ……………………………………………………………………………………………………………. 16 ADJUSTING THE VOLUME ……………………………………………………………………………………………………………………………….. 17
ON-SCREEN DISPLAY (OSD) MENU SETTINGS…………………………………………………………………………………………. 18
OSD MENU CONTROLS ………………………………………………………………………………………………………………………………….. 18 Navigating the OSD …………………………………………………………………………………………………………………………………… 18
SETTING THE OSD LANGUAGE ………………………………………………………………………………………………………………………… 19 OSD MENU OVERVIEW ………………………………………………………………………………………………………………………………….. 20 OSD SUB- MENU OVERVIEW …………………………………………………………………………………………………………………………… 21 IMAGE MENU………………………………………………………………………………………………………………………………………………… 22
Advanced Feature ……………………………………………………………………………………………………………………………………… 23 Color Manager………………………………………………………………………………………………………………………………………….. 24 COMPUTER MENU………………………………………………………………………………………………………………………………………….. 25
U
VIDEO/AUDIO MENU ……………………………………………………………………………………………………………………………………… 26 Audio……………………………………………………………………………………………………………………………………………………….. 27
INSTALLATION I MENU …………………………………………………………………………………………………………………………………… 28 INSTALLATION II MENU………………………………………………………………………………………………………………………………….. 29
Advanced Feature ……………………………………………………………………………………………………………………………………… 30 OSD Menu Setting……………………………………………………………………………………………………………………………………… 31 Peripheral Test………………………………………………………………………………………………………………………………………….. 31 Lamp Hour Reset ………………………………………………………………………………………………………………………………………. 32 Network……………………………………………………………………………………………………………………………………………………. 32 3D …………………………………………………………………………………………………………………………………………………………… 33 Factory Reset ……………………………………………………………………………………………………………………………………………. 39 Status……………………………………………………………………………………………………………………………………………………….. 39
MAINTENANCE AND SECURITY………………………………………………………………………………………………………………… 40
REPLACING THE PROJECTION LAMP………………………………………………………………………………………………………………….. 40 Resetting the Lamp…………………………………………………………………………………………………………………………………….. 42
CLEANING THE PROJECTOR……………………………………………………………………………………………………………………………… 43 Cleaning the Lens ……………………………………………………………………………………………………………………………………… 43 Cleaning the Case ……………………………………………………………………………………………………………………………………… 43
USING THE KENSINGTON® LOCK ……………………………………………………………………………………………………………………… 44
TROUBLESHOOTING ………………………………………………………………………………………………………………………………….. 45
COMMON PROBLEMS AND SOLUTIONS ………………………………………………………………………………………………………………. 45 TIPS FOR TROUBLESHOOTING ………………………………………………………………………………………………………………………….. 45 LED ERROR MESSAGES………………………………………………………………………………………………………………………………….. 46 IMAGE PROBLEMS………………………………………………………………………………………………………………………………………….. 46 LAMP PROBLEMS …………………………………………………………………………………………………………………………………………… 47 REMOTE CONTROL PROBLEMS ………………………………………………………………………………………………………………………… 47
— vi —

Search

PPrreeffaaccee
AUDIO PROBLEMS …………………………………………………………………………………………………………………………………………. 48 HAVING THE PROJECTOR SERVICED …………………………………………………………………………………………………………………. 48 HDMITM Q & A…………………………………………………………………………………………………………………………………………….. 49 SPECIFICATIONS…………………………………………………………………………………………………………………………………………. 50 SPECIFICATIONS…………………………………………………………………………………………………………………………………………….. 50 PROJECTION DISTANCE VS. PROJECTION SIZE…………………………………………………………………………………………………….. 51
Projection Distance and Size Table ……………………………………………………………………………………………………………… 51 TIMING MODE TABLE …………………………………………………………………………………………………………………………………….. 51 PROJECTOR DIMENSIONS ………………………………………………………………………………………………………………………………… 54 REGULATORY COMPLIANCE ……………………………………………………………………………………………………………………. 55 FCC WARNING……………………………………………………………………………………………………………………………………………… 55 CANADA ………………………………………………………………………………………………………………………………………………………. 55 SAFETY CERTIFICATIONS………………………………………………………………………………………………………………………………… 55
­ vii ­

Search

DDLLPP PPrroojjeeccttoorr­­ UUsseerr”ss MMaannuuaall
GETTING STARTED
Packing Checklist
Carefully unpack the projector and check that the following items are included:

DLP PROJECTOR WITH LENS CAP

RGB CABLE

POWER CORD

USB CABLE

REMOTE CONTROL (WITH TWO AAA BATTERIES)

ICON STRIP

CD-ROM (THIS USER’S MANUAL)

Contact your dealer immediately if any items are missing, appear damaged, or if the unit does not work. It is recommend that you keep the original packing material should you ever need to return the equipment for warranty service.
Caution: Avoid using the projector in dusty environments.

­ 1 ­

Search

DDLLPP PPrroojjeeccttoorr—-UUsseerr”ss MMaannuuaall
Views of Projector Parts Front-right View

ITEM

LABEL

DESCRIPTION

SEE PAGE:

Height-adjuster button

Push to release height adjuster

15

Height adjuster

Adjusts level of projector

Lens cap

Protect lens when not in use

Lens

Projection Lens

IR receiver

Receive IR signal from remote control

6

Focus ring

Function keys

Focuses the projected image

16

See Top view–On-screen Display (OSD) buttons and LEDs.

3

Important: Ventilation openings on the projector allow for good air circulation, which keeps the projector lamp cool. Do not obstruct any of the ventilation openings.

­ 2 ­

Search

DDLLPP PPrroojjeeccttoorr­­ UUsseerr”ss MMaannuuaall
Top view–On-screen Display (OSD) buttons and LEDs

ITEM 1. 2. 3. 4. 5. 6. 7. 8. 9. 10.

LABEL
(Power button) BLANK
(Left cursor) / Volume
Enter
MENU
(Up cursor) / Keystone+
AUTO
(Right cursor) / Volume
SOURCE (Down cursor) / Keystone-

11. READY LED

12. TEMP LED

DESCRIPTION
Turns the projector On or Off.

SEE PAGE:
11

Displays a blank screen and mutes audio

Navigates and changes settings in the OSD Quick Menu ­ For Volume

Enter or confirm highlighted OSD menu item
18
Opens and exits OSD menus

Navigates and changes settings in the OSD Quick Menu ­ For Keystone

Optimizes image size, position, and resolution

Navigates and changes settings in the OSD Quick Menu ­ For Volume

18

Enter the Source menu

10

Navigates and changes settings in the OSD Quick Menu ­ For Keystone

18

Red Flashing Flashing

Lamp is ready to be powered-on.
Lamp not ready (Warm-up/shutting down/cooling) (see LED Error Messages on page 46) Error code

­ 3 ­

Search

DDLLPP PPrroojjeeccttoorr—-UUsseerr”ss MMaannuuaall

Rear view

12 3 4 5

6

7 8 9 10 11

14 13

12

ITEM

LABEL

DESCRIPTION

SEE PAGE:

AC IN

Connect the POWER CABLE

11

(USB)

Connect the USB CABLE from a computer

VGA OUT

Connect the RGB CABLE to a display (Loop Thru only for VGA IN-1)

LAN

Connect a LAN CABLE from Ethernet

VGA IN ­ 1

Connect the RGB CABLE from a computer and components

VGA IN ­ 2

Connect the RGB CABLE from a computer and components

10

HDMITM

Connect the HDMITM CABLE from a HDMITM device

S-VIDEO IN

Connect the S-VIDEO CABLE from a video device

VIDEO IN

Connect the COMPOSITE CABLE from a video device

10. Speaker

Outputs audio sound

Kensington Lock

Secure to permanent object with a Kensington® Lock system

44

AUDIO IN (L and R)

Connect the AUDIO CABLES from a audio device

13. RS-232

Connect RS-232 serial port cable for remote control

10

AUDIO IN
14.
AUDIO OUT

Connect an AUDIO CABLE from the input device Connect an AUDIO CABLE for audio loop through

Note: If your video equipment has various input sources, it is recommended to connect in priority of HDMITM/DVI, component (thru VGA), S-Video, Composite for better picture quality.

­ 4 ­

Search

Bottom view

1

2

DDLLPP PPrroojjeeccttoorr­­ UUsseerr”ss MMaannuuaall

34

2

ITEM 1. 2. 3. 4.

LABEL
Tilt adjustor Ceiling support holes Height adjustor Height adjustor button

DESCRIPTION

SEE PAGE:

Rotate adjuster lever to adjust angle position.

15

Contact your dealer for information on mounting the projector on a ceiling
Adjuster drops down when adjuster button is pushed.
15
Push to release adjustor.

Note: When installing, ensure that you use only UL Listed ceiling mounts. For ceiling installations, use approved mounting hardware and M4 screws with a maximum screw depth of 6 mm (0.23 inch). The construction of the ceiling mount must be of a suitable shape and strength. The ceiling mount load capacity must exceed the weight of the installed equipment, and as an additional precaution be capable of withstanding three times the weight of the equipment (not less than 5.15 kg) over a period of 60 seconds.

­ 5 ­

Search

DDLLPP PPrroojjeeccttoorr—-UUsseerr”ss MMaannuuaall

Remote Control Parts

28

1

2

27

3

4

26 25

5 6

24

7

23

8

22

9

21 20

10 11

19

12

18

13

17

14

16 15
Important: 1. Avoid using the projector with bright fluorescent lighting turned on. Certain high-frequency fluorescent lights can disrupt remote control operation.
2. Be sure nothing obstructs the path between the remote control and the projector. If the path between the remote control and the projector is obstructed, you can bounce the signal off certain reflective surfaces such as projector screens.
3. The buttons and keys on the projector have the same functions as the corresponding buttons on the remote control. This user’s manual describes the functions based on the remote control.

­ 6 ­

Search

DDLLPP PPrroojjeeccttoorr­­ UUsseerr”ss MMaannuuaall

ITEM 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. 12. 13. 14. 15. 16. 17. 18. 19. 20.
21. 22. 23. 24. 25. 26. 27. 28.

LABEL
IR transmitter Status LED Laser Up Right Down Page Down Up cursor Right cursor Down cursor Volume +/Mute

DESCRIPTION
Transmits signals to projector Lights when the remote control is used Press to operate the on-screen pointer Up arrow when connected through USB to a PC Right arrow when connected through USB to a PC Down arrow when connected through USB to a PC Page down when connected through USB to a PC
Navigates and changes settings in the OSD
Adjusts volume Mutes the built-in speaker

Zoom+

Zoom in

Zoom-

Zoom out

Freeze

Freeze/unfreezes the on-screen picture

Blank

Makes the screen blank

Source

Detects the input device

Auto

Auto adjustment for phase, tracking, size, position

Menu

Opens the OSD

Status Keystone top/bottom

Opens the OSD Status menu (the menu only opens when an input device is detected)
Corrects image-trapezoid (wider top/bottom) effect

Left cursor

Navigates and changes settings in the OSD

Enter

Changes settings in the OSD

Page Up

Page up when connected through USB to a PC

Left

Left arrow when connected through USB to a PC

Enter

Enter key when connected through USB to a PC

Power

Turns the projector on or off

Laser

Use as on-screen pointer. DO NOT POINT IN EYES.

SEE PAGE:
18 17 16
18 39 16 18 11

­ 7 ­

Search

DDLLPP PPrroojjeeccttoorr—-UUsseerr”ss MMaannuuaall
Remote Control Operating Range
The remote control uses infrared transmission to control the projector. It is not necessary to point the remote directly at the projector. Provided you are not holding the remote perpendicular to the sides or the rear of the projector, the remote will function well within a radius of about 7 meters (23 feet) and 15 degrees above or below the projector level. If the projector does not respond to the remote control, move a little closer.
Projector and Remote Control Buttons
The projector can be operated using the remote control or the buttons on the top of the projector. All operations can be carried out with the remote control; however, the buttons on the projector are limited in use.
­ 8 ­

Search

Inserting the Remote Control Batteries
1. Remove the battery compartment cover
by sliding the cover in the direction of the arrow.

DDLLPP PPrroojjeeccttoorr­­ UUsseerr”ss MMaannuuaall
SETUP AND OPERATION

2. Insert the battery with the positive side
facing up.

3. Replace the cover.

Caution: 1. Only use AAA batteries (Alkaline batteries are recommended). 2. Dispose of used batteries according to local ordinance regulations. 3. Remove the batteries when not using the projector for prolonged periods.
­ 9 ­

Search

DDLLPP PPrroojjeeccttoorr—-UUsseerr”ss MMaannuuaall

Connecting Input Devices

A PC or notebook computer and video devices can be connected to the projector at the same time. Video devices include DVD, VCD, and VHS players, as well as movie camcorders and digital still cameras. Check the user manual of the connecting device to confirm it has the appropriate output connector.

A B CD

EF

GH I

K

J

ITEM
A B C D E
F
G H I J K

LABEL
(USB) VGA OUT LAN VGA IN ­ 1 VGA IN ­ 2 AUDIO IN AUDIO OUT HDMITM S-VIDEO VIDEO IN AUDIO IN (L and R) RS-232C

DESCRIPTION
Connect the USB CABLE from a computer Connect the RGB CABLE to a display (Loop Thru only for VGA IN-1) Connect a LAN CABLE from Ethernet Connect the RGB CABLE from a computer and components Connect the RGB CABLE from a computer and components Connect an AUDIO CABLE from the input device Connect an AUDIO CABLE for audio loop through Connect the HDMITM CABLE from a HDMITM device Connect the S-VIDEO CABLE from a video device Connect the COMPOSITE CABLE from a video device Connect the AUDIO CABLES from a audio device Connect the RS-232 serial cable for remote control

Warning: As a safety precaution, disconnect all power to the projector and connecting devices before making connections.

­ 10 ­

Search

Starting and Shutting down the Projector
1. Connect the power cord to the projector.
Connect the other end to a wall outlet. The POWER and READY LEDs on the projector light.
2. Turn on the connected devices.
3. Ensure the READY LED displays a
solid red and not a flashing red. Then press the POWER button to turn on the projector.
The projector splash screen displays and connected devices are detected.
See Setting an Access Password (Security Lock)on page 13 if security lock is enabled.
4. If more than one input device is con-
nected, press the SOURCE button and use to scroll among devices. (Component is supported through the RGB to COMPONENT ADAPTER.)

DDLLPP PPrroojjeeccttoorr­­ UUsseerr”ss MMaannuuaall

· VGA 1/VGA 2: Analog RGB Component: DVD input YCbCr / YPbPr, or HDTV input YPbPr via HD15 connector
· Composite Video: Traditional composite video · S-Video: Super video (Y/C separated) · HDMI: HDMI, DVI
­ 11 ­

Search

DDLLPP PPrroojjeeccttoorr—-UUsseerr”ss MMaannuuaall
5. When the “Power Off? /Press Power
again” message appears, press the POWER button. The projector turns off. Caution: 1. Be sure to remove the lens cap before starting projector. 2. Do not unplug the power cord until the READY LED stops flashing­indicating the projector has cooled down.
­ 12 ­

Search

DDLLPP PPrroojjeeccttoorr­­ UUsseerr”ss MMaannuuaall
Setting an Access Password (Security Lock)
You can use the four (arrow) buttons to set a password and prevent unauthorized use of the projector. When enabled, the password must be entered after you power on the projector. (See Navigating the OSD on page 18 and Setting the OSD Language on page 19 for help on using OSD menus.) Important: Keep the password in a safe place. Without the password, you will not be able to use the projector. If you lose the password, contact your reseller for information on clearing the password.
1. Press the MENU button to open the OSD
menu.
2. Press the cursor button to move to
the Installation I menu.
3. Press the cursor button to select
Security Lock.
4. Press the cursor button to enable or disable security lock function. A password dialog box automatically appears.
­ 13 ­

Search

DDLLPP PPrroojjeeccttoorr—-UUsseerr”ss MMaannuuaall
5. You can use the cursor buttons
either on keypad or IR remote control for password entry. You can use any combination including the same arrow five times, but not less than five. Press the cursor buttons in any order to set the password. Push the MENU button to exit the dialog box.
6. The password confirm menu appears when
user presses the power-on key in case the Security Lock is enabled. Enter the password in the order you set it at step 5. In case you forget the password, please contact the service center. Service center will validate the owner and help reset the password.
­ 14 ­

Search

DDLLPP PPrroojjeeccttoorr­­ UUsseerr”ss MMaannuuaall
Adjusting the Projector Level
Take note of the following when setting up the projector: · The projector table or stand should be level and sturdy. · Position the projector so that it is perpendicular to the screen. · Ensure the cables are in a safe location. You could trip over them.
1. To raise the level of the projector, lift the projector [A] and press the height-adjuster
button [B]. The height adjuster drops down [C].
2. To lower the level of the projector, press the height-adjuster button and push down
on the top of the projector.
3. To adjust the angle of the picture, turn the tilt-adjuster [D] right or left until the
desired angle has been achieved.
­ 15 ­

Search

DDLLPP PPrroojjeeccttoorr—-UUsseerr”ss MMaannuuaall
Adjusting the Focus and Keystone
1. Use the Image-focus
control (on the projector only) to sharpen the projected image.

2. Use the KEYSTONE
buttons (on the projector or the remote control) to correct image-trapezoid (wider top or bottom) effect.
3. The keystone control
appears on the display.

Remote control and OSD panel

­ 16 ­

Search

Adjusting the Volume
1. Press the Volume +/-
buttons on the remote control. The volume control appears on the display.
2. Press the Left or Right
Cursor buttons on the keypad to adjust Volume +/-.
3. Press the MUTE button to
turn off the volume (This feature is available only on the remote).

DDLLPP PPrroojjeeccttoorr­­ UUsseerr”ss MMaannuuaall

­ 17 ­

Search

DDLLPP PPrroojjeeccttoorr—-UUsseerr”ss MMaannuuaall
ON-SCREEN DISPLAY (OSD) MENU SETTINGS
OSD Menu Controls
The projector has an OSD that lets you make image adjustments and change various settings.
Navigating the OSD
You can use the remote control cursor buttons or the buttons on the top of the projector to navigate and make changes to the OSD. The following illustration shows the corresponding buttons on the projector.

1

5

2

MENU

AUTO

3

5

6

MODE / Enter

6

1

6

7

BLANK

SOURCE

4

2

3

7

4

1

1. To enter the OSD, press the MENU button.
2. There are five menus. Press the cursor button to move through the menus.
3. Press the cursor button to move up and down in a menu.
4. Press to change values for settings.
5. Press MENU to close the OSD or leave a submenu.
Note: Depending on the video source, not all items in the OSD are available. For example, the Horizontal/Vertical Position items in the Computer menu can only be modified when connected to a PC. Items that are not available cannot be accessed and are grayed out.

­ 18 ­

Search

DDLLPP PPrroojjeeccttoorr­­ UUsseerr”ss MMaannuuaall
Setting the OSD Language
Set the OSD language to your preference before continuing. 1. Press the MENU button. Press the cursor button to navigate to Installation I.
2. Press the cursor button until Language is highlighted.
3. Press the cursor button until the language you want is highlighted. 4. Press the MENU button twice to close the OSD.
­ 19 ­

Search

DDLLPP PPrroojjeeccttoorr—-UUsseerr”ss MMaannuuaall
OSD Menu Overview
Use the following illustration to quickly find a setting or determine the range for a setting.
­ 20 ­

Search

OSD Sub-Menu Overview

DDLLPP PPrroojjeeccttoorr­­ UUsseerr”ss MMaannuuaall

­ 21 ­

Search

DDLLPP PPrroojjeeccttoorr—-UUsseerr”ss MMaannuuaall
Image Menu
Press the MENU button to open the OSD menu. Press the cursor button to move to the Image Menu. Press the cursor button to move up and down in the Image menu. Press to change values for settings.

ITEM
Display Mode Brilliant Color Brightness Contrast Sharpness Gamma Advanced Reset

DESCRIPTION
Press the cursor button to set the Display Mode. Press the cursor button to adjust the Brilliant Color value. Press the cursor button to adjust the display brightness. Press the cursor button to adjust the display contrast. Press the cursor button to adjust the display sharpness level. Press the cursor button to adjust the gamma correction of the display. Press (Enter) / to enter the Advanced menu. See Advanced Feature on page 23. Press (Enter) / to reset all settings to default values.

­ 22 ­

Search

DDLLPP PPrroojjeeccttoorr­­ UUsseerr”ss MMaannuuaall
Advanced Feature
Press the Menu button to open the OSD menu. Press to move to the Image menu. Press to move to the Advanced menu and then press Enter or . Press to move up and down in the Advanced menu.

ITEM
Color Space Color Temperature Color Manager

DESCRIPTION
Press the cursor button to adjust the color space. (Range: Auto ­ RGB ­ YPbPr ­ YCbCr)
Press the cursor button to adjust the color temperature. (Range: Cold ­ Normal ­ Warm)
Press (Enter) / to enter the color manager menu. (Range: Red-Green-Blue- CyanMagenta-Yellow-White). See page 24 for more information on Color Manager.

­ 23 ­

Search

DDLLPP PPrroojjeeccttoorr—-UUsseerr”ss MMaannuuaall
Color Manager
Press (Enter) / to enter the Color Manager sub menu.

ITEM
Red Green Blue Cyan Magenta Yellow White

DESCRIPTION
Select to enter the Red Color Manager. Press the buttons to adjust the Hue, Saturation, and Gain.
Select to enter the Green Color Manager. Press the buttons to adjust the Hue, Saturation, and Gain.
Select to enter the Blue Color Manager. Press the buttons to adjust the Hue, Saturation, and Gain.
Select to enter the Cyan Color Manager. Press the buttons to adjust the Hue, Saturation, and Gain.
Select to enter the Magenta Color Manager. Press the buttons to adjust the Hue, Saturation, and Gain.
Select to enter the Yellow Color Manager. Press the buttons to adjust the Hue, Saturation, and Gain.
Select to enter the White Color Manager. Press the buttons to adjust the Red, Green, and Blue.

­ 24 ­

Search

DDLLPP PPrroojjeeccttoorr­­ UUsseerr”ss MMaannuuaall
Computer Menu
Press the MENU button to open the OSD menu. Press the cursor button to move to the Computer menu. Press the cursor button to move up and down in the computer menu. Press to change values for settings.

ITEM

DESCRIPTION

Horizontal Position Press the cursor button to adjust the display position to left or right.

Vertical Position

Press the cursor button to adjust the display position to up or down.

Frequency

Press the cursor button to adjust the A/D sampling clock.

Tracking

Press the cursor button to adjust the A/D sampling dot.

Auto Image

Press (Enter) / to automatically adjustment for phase, tracking, size and position.

­ 25 ­

Search

DDLLPP PPrroojjeeccttoorr—-UUsseerr”ss MMaannuuaall
Video/Audio Menu
Press the MENU button to open the OSD menu. Press the cursor button to move to the Video/Audio menu. Press the cursor button to move up and down in the Video/Audio menu. Press to change values for settings.

ITEM
Video AGC Video Saturation Video Tint Film Mode Video Overscan Closed Captioning Audio Reset

DESCRIPTION
Press the buttons to enable or disable the Automatic Gain Control for video source. Press the buttons to adjust the video saturation. Press the buttons to adjust the video tint/hue. Press the buttons to select a different film mode. Press the buttons to enable or disable video over scan. Press the buttons to enable or disable Closed Captioning Press (Enter) / to enter the Audio menu. See Audio on page 27. Press (Enter) / to reset all settings to default values.

Note: Video jagging may occur when playing interlace video. To overcome this issue, open the Video / Audio menu and adjust the Film Mode feature.

­ 26 ­

Search

Audio
Press (Enter) / to enter the Audio sub menu.

DDLLPP PPrroojjeeccttoorr­­ UUsseerr”ss MMaannuuaall

ITEM
Volume Mute Audio Input

DESCRIPTION
Press the buttons to adjust the audio volume. Press the buttons to turn on or off the speaker. Press the cursor button to select audio input.

­ 27 ­

Search

DDLLPP PPrroojjeeccttoorr—-UUsseerr”ss MMaannuuaall
Installation I Menu
Press the MENU button to open the OSD menu. Press the cursor button to move to the Installation I menu. Press the cursor button to move up and down in the Installation I menu. Press to change values for settings.

ITEM
Language Blank Screen Projection Security Lock Aspect Ratio Keystone Digital Zoom
Reset

DESCRIPTION
Press the cursor button to select a different localization Menu. Press the cursor button to select different color to blank the screen. Press the cursor button to choose from four projection methods: Press the cursor button to enable or disable security lock function. Press the cursor button to adjust the video aspect ratio. Press the cursor button to adjust the display keystone. Press the cursor button to adjust the Digital Zoom menu. Press (Enter) / to reset all settings to default values (except Language and Security Lock).

­ 28 ­

Search

DDLLPP PPrroojjeeccttoorr­­ UUsseerr”ss MMaannuuaall
Installation II Menu
Press the MENU button to open the OSD menu. Press the cursor button to move to the Installation II menu. Press the cursor button to move up and down in the Installation II menu.

ITEM
Auto Source Auto Power Off (min.) Auto Power On
Fan Speed
Lamp Mode Advanced Factory Reset Status

DESCRIPTION
Press the cursor button to enable or disable automatic source detection.
Press the cursor button to enable or disable automatic shutdown of lamp when no signal.
Press the cursor button to enable or disable automatic power On when AC power is supplied. Press the cursor button to toggle between Normal and High fan speeds. Note: We recommend selecting high speed in high temperatures, high humidity, or high altitude areas. Press the cursor button to select the lamp mode for higher brightness or lower brightness to save lamp life. Press (Enter) / to enter the Advanced menu. See Advanced Feature on page 30. Press (Enter) / to reset all items to factory preset values. Press (Enter) / to enter the Status menu. See page 39 for more information on Status.

­ 29 ­

Search

DDLLPP PPrroojjeeccttoorr—-UUsseerr”ss MMaannuuaall
Advanced Feature
Press the Menu button to open the OSD menu. Press to move to the Installation II menu. Press to move to the Advanced menu and then press Enter or . Press to move up and down in the Advanced menu. Press to change values for setting.

ITEM
OSD Menu Setting Peripheral Test Lamp Hour Reset Low Power Mode RS232 Network 3D

DESCRIPTION
Press (Enter) / to enter the OSD setting menu. See page 31 for more information on OSD Menu Setting.
Press (Enter) / to enter the Peripheral Test menu. See page 31 for more information on Peripheral Test.
After replacing the lamp, this item should be reset. See page 32 for more information on Lamp Hour Reset.
Press to turn Low Power Mode on or off.
Press to select RS232 (remote) or Network (LAN) mode depending on projector connection method.
Press (Enter) / to enter the Network menu. See page 32 for more information on Network settings.
Press (Enter)/ to enter the 3D menu. See page 31 for more information on 3D setting..

Note: To enjoy the 3D function, first enable the Play Movie in 3D setting found in your DVD device under the 3D Disc Menu.

­ 30 ­

Search

OSD Menu Setting

DDLLPP PPrroojjeeccttoorr­­ UUsseerr”ss MMaannuuaall

ITEM

DESCRIPTION

Menu Position Translucent Menu Menu Display

Press button to select different OSD location. Press button to select OSD background translucent level. Press button to select OSD timeout delay.

Peripheral Test

ITEM
Remote Control Test USB Test Button Test Color Test Sound Test

Press Press Press Press Press

DESCRIPTION
(Enter) / to test the IR remote controller for diagnostic. (Enter) / to test the USB connection with connected PC. (Enter) / to test the button on keypad. (Enter) / to select different colors on screen. (Enter) / to test sound output.

­ 31 ­

Search

DDLLPP PPrroojjeeccttoorr—-UUsseerr”ss MMaannuuaall
Lamp Hour Reset
Please refer to Resetting the Lamp on page 42 to reset the lamp hour counter.
Network

ITEM
Network State
DHCP
IP Address Subnet Mask Gateway DNS Apply

DESCRIPTION
Displays the network connection status. Press to turn DHCP On or Off. Note: If you select DHCP Off, complete the IP Address, Subnet Mask, Gateway, and DNS fields. Enter a valid IP address if DHCP is turned off. Enter a valid Subnet Mask if DHCP is turned off. Enter a valid Gateway address if DHCP is turned off. Enter a valid DNS name if DHCP is turned off. Press (Enter) / to confirm settings.

­ 32 ­

Search

DDLLPP PPrroojjeeccttoorr­­ UUsseerr”ss MMaannuuaall
3D

ITEM
3D 3D Sync Invert

DESCRIPTION
Press to select Off, DLP-Link or IR. Press to turn 3D Sync Invert L / R or R / L.

­ 33 ­

Search

DDLLPP PPrroojjeeccttoorr—-UUsseerr”ss MMaannuuaall
For simplicity and ease of operation, the projector provides diverse networking and remote management features. The LAN/RJ45 function of the projector through a network, such as remotely manage: Power On/Off, Brightness and Contrast settings. Also, projector status information, such as: Video- Source, SoundMute, etc.
LAN_RJ45 1. Connect an RJ45 cable to RJ45 ports on the projector and the PC (Laptop).
2. On the PC (Laptop), select Start ´ Control Panel ´ Network Connections.
­ 34 ­

Search

DDLLPP PPrroojjeeccttoorr­­ UUsseerr”ss MMaannuuaall
3. Right-click on Local Area Connection, and select Properties.
4. In the Properties window, select the General tab, and select Internet Protocol (TCP/IP). 5. Click Properties.
6. Click Use the following IP address and fill in the IP address and Subnet mask, then click OK.
­ 35 ­

Search

DDLLPP PPrroojjeeccttoorr—-UUsseerr”ss MMaannuuaall
7. Press the Menu button on the projector. 8. Select Installation II ´ Advanced ´ Network. 9. After getting into Network, input the following:
DHCP: Off IP Address: 192.168.10.10 Subnet Mask: 255.255.255.0 Gateway: 0.0.0.0 ` DNS Server: 0.0.0.0 10. Press (Enter) / to confirm settings. 11. Open a web browser (for example, Microsoft Internet Explorer).
12. In the Address bar, input the IP address: 192.168.10.10. 13. Press (Enter) / .
The projector is setup for remote management. The LAN/RJ45 function displays as follows.
­ 36 ­

Search

14. Click Control Panel to display projector settings.

DDLLPP PPrroojjeeccttoorr­­ UUsseerr”ss MMaannuuaall

Preparing Email Alerts 1. Make sure that user can access the homepage of LAN RJ45 function by web browser (for example, Microsoft Internet Explorer v6.01/v7.0). 2. From the Homepage of LAN/RJ45, click Alert Setting.
3. By default, these input boxes in Alert Setting are blank.

­ 37 ­

Search

DDLLPP PPrroojjeeccttoorr—-UUsseerr”ss MMaannuuaall
4. The To field is the recipients email address (for example, projector administrator). This is a required field. The Cc field sends a carbon copy of the alert to the specified email address. This is an optional field (for example, assistant of projector administrator). This Cc field is optional input. The “Subject” field is the subtitle for email. This is a required field. The From field is the sender’s email address (for example, projector administrator). This is a required field. The SMTP field is the mail server for sending out email (SMTP protocol). This is a required field. Select the alerting conditions by checking the desired boxes. See the example below:
5. When the above necessary input fields correct, then press Email Alert Test button. In a few seconds, the specified mailbox receives a test email as shown below:
Note: Fill in all fields as specified. Select the desired alert condition and click Submit to conduct an Email Alert Test. A successful test alerts the designated email accounts. To create an email alert, you must select alert conditions and enter a correct email address.
Group and Projector Name identify the alerting projector and are located at the top of the LAN RJ45 web page as shown below:
­ 38 ­

Search

DDLLPP PPrroojjeeccttoorr­­ UUsseerr”ss MMaannuuaall
Factory Reset
Press the cursor button to move up and down in the Installation II menu. Select the Factory Reset sub menu and press (Enter) / to reset all the menu items to the factory default values (expect Language and Security Lock).
Status
Press the cursor button to move up and down in the Installation II menu. Select the Installation II sub menu and press (Enter) / to enter the Status sub menu.

ITEM
Active Source Video Information Lamp Hours

DESCRIPTION
Display the activated source. Displays resolution/video information for RGB source and color standard for Video source. Lamp hour used information is displayed. Eco and Normal counters are separated.

­ 39 ­

Search

DDLLPP PPrroojjeeccttoorr—-UUsseerr”ss MMaannuuaall

MAINTENANCE AND SECURITY

Replacing the Projection Lamp
The projection lamp should be replaced when it burns out. It should only be replaced with a certified replacement part, which you can order from your local dealer.
Important: a. The projection lamp used in this product contains a small amount of mercury.
b. Do not dispose this product with general household waste.
c. Disposal of this product must be carried out in accordance with the regulations of your local authority.

Warning: Be sure to turn off and unplug the projector at least 30 minutes before replacing the lamp. Failure to do so could result in a severe burn.
1. Remove the single screw on
the lamp compartment cover.

2. Remove the lamp compart-
ment cover.

­ 40 ­

Search

3. Remove the three screws from
the lamp module.
4. Lift the module handle up.

DDLLPP PPrroojjeeccttoorr­­ UUsseerr”ss MMaannuuaall

5. Pull firmly on the module handle to remove the lamp module.

6. Reverse steps 1 to 5 to install the new lamp module. While installing, align the lamp module with the connector and ensure it is level to avoid damage.
Note: The lamp module must sit securely in place and the lamp connector must be connected properly before tightening the screws.
­ 41 ­

Search

DDLLPP PPrroojjeeccttoorr—-UUsseerr”ss MMaannuuaall
Resetting the Lamp
After replacing the lamp, you should reset the lamp hour counter to zero. Refer to the following:
1. Press the MENU button to open the
OSD menu.
2. Press the cursor button to move
to the Installation II menu. Press the cursor button to move down to Advanced.
3. Press the cursor button to move
down to Lamp Hour Reset.
4. Press the cursor or Enter button.
A message screen appears.
5. Press buttons to reset the
lamp hour.
6. Press the MENU button to get back
to Installation II.
­ 42 ­

Search

DDLLPP PPrroojjeeccttoorr­­ UUsseerr”ss MMaannuuaall
Cleaning the Projector
Cleaning the projector to remove dust and grime will help ensure trouble-free operation. Warning: 1. Be sure to turn off and unplug the projector at least 30 minutes before cleaning. Failure to do so could result in a severe burn. 2. Use only a dampened cloth when cleaning. Do not allow water to enter the ventilation openings on the projector. 3. If a little water gets into the projector interior while cleaning, leave unplugged in a well-ventilated room for several hours before using. 4. If a lot of water gets into the projector interior when cleaning, have the projector serviced.
Cleaning the Lens
You can purchase optic lens cleaner from most camera stores. Refer to the following to clean the projector lens.
1. Apply a little optic lens cleaner to a clean soft cloth. (Do not apply the cleaner directly to the lens.)
2. Lightly wipe the lens in a circular motion. Caution: 1. Do not use abrasive cleaners or solvents. 2. To prevent discoloration or fading, avoid getting cleaner on the projector case.
Cleaning the Case
Refer to the following to clean the projector case. 1. Wipe off dust with a clean dampened cloth. 2. Moisten the cloth with warm water and mild detergent (such as used to wash dishes), and then wipe the case. 3. Rinse all detergent from the cloth and wipe the projector again.
Caution: To prevent discoloration or fading of the case, do not use abrasive alcohol-based cleaners.
­ 43 ­

Search

DDLLPP PPrroojjeeccttoorr—-UUsseerr”ss MMaannuuaall
Using the Kensington® Lock
If you are concerned about security, attach the projector to a permanent object with the Kensington slot and a security cable.
Note: Contact your vendor for details on purchasing a suitable Kensington security cable. The security lock corresponds to Kensington’s MicroSaver Security System. If you have any comment, contact: Kensington, 2853 Campus Drive, San Mateo, CA 94403, U.S.A. Tel: 800-535-4242, http://www.Kensington.com.
­ 44 ­

Search

DDLLPP PPrroojjeeccttoorr­­ UUsseerr”ss MMaannuuaall
TROUBLESHOOTING
Common problems and solutions
These guidelines provide tips to deal with problems you may encounter while using the projector. If the problem remains unsolved, contact your dealer for assistance. Often after time spent troubleshooting, the problem is traced to something as simple as a loose connection. Check the following before proceeding to the problem-specific solutions.
· Use some other electrical device to confirm that the electrical outlet is working. · Ensure the projector is turned on. · Ensure all connections are securely attached. · Ensure the attached device is turned on. · Ensure a connected PC is not in suspending mode. · Ensure a connected notebook computer is configured for an external display.
(This is usually done by pressing a Fn-key combination on the notebook).
Tips for Troubleshooting
In each problem-specific section, try the steps in the order suggested. This may help you to solve the problem more quickly. Try to pin point the problem and thus avoid replacing non-defective parts. For example, if you replace batteries and the problem remains, put the original batteries back and go to the next step. Keep a record of the steps you take when troubleshooting: The information may be useful when calling for technical support or for passing on to service personnel.
­ 45 ­

Search

DDLLPP PPrroojjeeccttoorr—-UUsseerr”ss MMaannuuaall

LED Error Messages

ERROR CODE MESSAGES

POWER LED READY LED TEMP LED

BLINK

BLINK

BLINK

Over temperature

OFF

OFF

ON

G794 fail

4

4

OFF

T1 fail

4

5

OFF

Lamp error

5

OFF

OFF

Ballast Over Temperature

5

1

OFF

Ballast shot circuit in output detected

5

2

OFF

End of lamp lift detected

5

3

OFF

Ballast lamp did not ignite

5

4

OFF

Lamp extinguished during normal operation

5

5

OFF

Lamp extinguished during run-up phase

5

6

OFF

Lamp Memory write error

5

7

OFF

Lamp Memory write buffer overflow

5

8

OFF

Lamp UART buffer overflow

5

9

OFF

Lamp current calculation error

5

10

OFF

Lamp Corrupted software configuration

5

11

OFF

Lamp voltage too low

5

12

OFF

Lamp FLASH memory CRC error Lamp EEPROM memory CRC error

5

13

OFF

5

14

OFF

Lamp EEPROM configuration does not match FLASH kernel

5

15

OFF

Fan1 error (Burner Fan)

6

1

OFF

Fan2 error (Lamp Fan)

6

2

OFF

Fan3 error (Power Fan)

6

3

OFF

Fan4 error (DMD Fan)

6

4

OFF

Lamp door open

7

OFF

OFF

DMD error

8

OFF

OFF

Color wheel error

9

OFF

OFF

In the event of an error, please disconnect the AC power cord and wait for one (1) minute before restarting the projector. If the POWER or LAMP LEDs are still blinking or the TEMP LED is lit, contact your service center.

­ 46 ­

Search

DDLLPP PPrroojjeeccttoorr­­ UUsseerr”ss MMaannuuaall
Image Problems
Problem: No image appears on the screen 1. Verify the settings on your notebook or desktop PC. 2. Turn off all equipment and power up again in the correct order.
Problem: The image is blurred 1. Adjust the Focus on the projector. 2. Press the Auto button on the remote control or projector. 3. Ensure the projector- to-screen distance is within the 10-meter (33-feet) specified range. 4. Check that the projector lens is clean.
Problem: The image is wider at the top or bottom (trapezoid effect) 1. Position the projector so it is as perpendicular to the screen as possible. 2. Use the Keystone button on the remote control or projector to correct the problem.
Problem: The image is reversed Check the Projection setting on the Installation I menu of the OSD.
Problem: The image is streaked 1. Set the Frequency and Tracking settings on the Computer menu of the OSD to the default settings. 2. To ensure the problem is not caused by a connected PC’s video card, connect to another computer.
Problem: The image is flat with no contrast Adjust the Contrast setting on the Image menu of the OSD.
Problem: The color of the projected image does not match the source image. Adjust the Color Temperature and Gamma settings on the Image menu of the OSD.
Lamp Problems
Problem: There is no light from the projector 1. Check that the power cable is securely connected. 2. Ensure the power source is good by testing with another electrical device. 3. Restart the projector in the correct order and check that the Power LED is green. 4. If you have replaced the lamp recently, try resetting the lamp connections. 5. Replace the lamp module. 6. Put the old lamp back in the projector and have the projector serviced.
Problem: The lamp goes off 1. Power surges can cause the lamp to turn off. Re- plug power cord. When the READY LED is on, press the power button. 2. Replace the lamp module. 3. Put the old lamp back in the projector and have the projector serviced.
Remote Control Problems
Problem: The projector does not respond to the remote control 1. Direct the remote control towards remote sensor on the projector. 2. Ensure the path between remote and sensor is not obstructed.
­ 47 ­

Search

DDLLPP PPrroojjeeccttoorr—-UUsseerr”ss MMaannuuaall
3. Turn off any fluorescent lights in the room. 4. Check the battery polarity. 5. Replace the batteries. 6. Turn off other Infrared-enabled devices in the vicinity. 7. Have the remote control serviced.
Audio Problems
Problem: There is no sound 1. Adjust the volume on the remote control. 2. Adjust the volume of the audio source. 3. Check the audio cable connection. 4. Test the source audio output with other speakers. 5. Have the projector serviced.
Problem: The sound is distorted 1. Check the audio cable connection. 2. Test the source audio output with other speakers. 3. Have the projector serviced.
Having the Projector Serviced
For problems operating the projector, please call PolyVision tech support as below Tech Support Manager. Please have your model & serial number available (label on bottom of unit). If it is determined that your unit requires service, the Technical Support Agent will instruct you how and where to return the unit.
For US & the Americas Tel.: 1-800-620-POLY (7659) Email: support@polyvision.com (works for the entire world, support in English & Spanish only) For UK only Contact Anders+Kern UK Ltd. Tel. +44(0)1638 510900 Email: support@anders-kern.co.uk For rest of Europe & the Middle East Tel.: +33-3 88 13 35 36 Email: eu.support@polyvision.com
­ 48 ­

Search

DDLLPP PPrroojjeeccttoorr­­ UUsseerr”ss MMaannuuaall
HDMITM Q & A
Q. What is the difference between a “Standard” HDMITM cable and a “High-Speed” HDMITM cable? Recently, HDMITM Licensing, LLC announced that cables would be tested as Standard or High-Speed cables. Standard (or “category 1”) HDMITM cables have been tested to perform at speeds of 75Mhz or up to 2.25Gbps, which is the equivalent of a 720p/1080i signal. High Speed (or “category 2”) HDMITM cables have been tested to perform at speeds of 340Mhz or up to 10.2Gbps, which is the highest bandwidth currently available over an HDMITM cable and can successfully handle 1080p signals including those at increased color depths and/or increased refresh rates from the Source. High-Speed cables are also able to accommodate higher resolution displays, such as WQXGA cinema monitors (resolution of 2560 x 1600).
Q. How do I run HDMITM cables longer than 10 meters? There are many HDMITM Adopters working on HDMITM solutions that extend a cable’s effective distance from the typical 10 meter range to much longer lengths. These companies manufacture a variety of solutions that include active cables (active electronics built into cables that boost and extend the cable’s signal), repeaters, amplifiers as well as CAT5/6 and fiber solutions.
Q. How can I tell if a cable is an HDMITM certified cable? All HDMITM products are required to be certified by the manufacturer as part of the HDMITM Compliance Test Specification. However, there may be instances where cables bearing the HDMITM logo are available but have not been properly tested. HDMITM Licensing, LLC actively investigates these instances to ensure that the HDMITM trademark is properly used in the market. We recommend that consumers buy their cables from a reputable source and a company that is trusted.
For more detail information check http://www.hdmi.org/learningcenter/faq.aspx#49
­ 49 ­

Search

DDLLPP PPrroojjeeccttoorr—-UUsseerr”ss MMaannuuaall

SPECIFICATIONS

Specifications
Model Display type Native Resolution Weight Projection distance Projection screen size Projection lens Vertical keystone correction Projection methods Data compatibility SDTV/EDTV/ HDTV Video compatibility H-Sync V-Sync Safety certification Operation temperature Dimensions AC Input Power consumption Stand By Lamp Audio speaker
Input Terminals
Output Terminals
Control Terminals
Security

PJ905 TI DMD 0.65″ WXGA
WXGA 1280×800 3.6 kg (7.9 lbs)
0.9 meters ~ 2.9 meters 88″~250″
Manual Focus
+/- 15 degrees
Front, Rear, Desktop/Ceiling (Rear, Front) VGA, SVGA, XGA, SXGA, UXGA, Mac 480i, 576i, 480p, 576p, 720p, 1080i, 1080p NTSC/NTSC 4.43, PAL (B/G/H/I/M/N/60), SECAM
15, 30 ­ 90 kHz 43 ­ 87 Hz
FCC-B, UL, cUL, CB, CE 5° ~ 35°C
335 mm (W) x 102 mm (H) x 256 mm (D) AC Universal 100 ~ 240, Typical @ 110VAC (100~240)/+-10%
290W <1 watt 230W 3W mono speaker VGA x 2 S-Video x 1 Composite Video x 1 HDMITM x 1 RCA stereo x 1 Mini-jack stereo x 1 VGA x 1 (Loop Thru only for VGA IN-1) Mini-jack stereo x 1 RS-232C RJ45 USB (type B) Kensington lock

­ 50 ­

Search

Projection Distance vs. Projection Size

DDLLPP PPrroojjeeccttoorr­­ UUsseerr”ss MMaannuuaall

Projection Distance and Size Table

PJ905

TELE

Distance (m)

1.01

1.36

2.05

Diagonal (inches) (*)

88.55

120

180

Keystone Correction Angle (degree)

38.13

38.13

38.13

Image Height (mm)

1192.1

1615.4

2423.2

Image Width (mm)

1907.3

2584.7

3387.0

A (mm)

194.5

263.6

395.5

Note: (*) 88.55″ is White Board dimension..

2.84 250 38.13 3365.5 5384.8 549.2

­ 51 ­

Search

DDLLPP PPrroojjeeccttoorr—-UUsseerr”ss MMaannuuaall

Timing Mode Table

The projector can display several resolutions. The following table outlines the resolutions that can be displayed by the projector.

SIGNAL
NTSC PAL/SECAM
VESA
Apple Macintosh SDTV EDTV

RESOLUTION
— — 720 x 400 640 x 480 640 x 480 640 x 480 640 x 480 800 x 600 800 x 600 800 x 600 800 x 600 800 x 600 1024 x 768 1024 x 768 1024 x 768 1024 x 768 1280 x 800 1280 x 800 1280 x 800 1280 x 1024 1280 x 1024 1280 x 1024 1400 x 1050 1440 x 900 1600 x1200 640 x 480 832 x 624 1024 x 768 1152 x 870 480i 576i 576p 480p

H-SYNC (KHZ)
15.734 15.625 37.9 31.5 37.9 37.5 43.3 35.2 37.9 46.9 48.1 53.7 48.4 56.5 60.0 68.7 49.7 62.8 71.6 64.0 80.0 91.1 65.3 55.9 75.0 35.0 49.7 60.2 68.7 15.734 15.625 31.3 31.5

V-SYNC (HZ)

COMPOSITE / S-VIDEO

COMPONENT

RGB (ANALOG)

DVI/ HDMITM (DIGITAL)

60.0

O

50.0

O

85.0

O

O

60.0

O

O

72.8

O

O

75.0

O

O

85.0

O

O

56.3

O

O

60.3

O

O

75.0

O

O

72.2

O

O

85.1

O

O

60.0

O

O

70.1

O

O

75.0

O

O

85.0

O

O

59.8

O

O

74.9

O

O

84.8

O

O

60.0

O

O

75.0

O

O

85.0

O

O

60.0

O

O

60.0

O

O

60

O

O

66.7

O

O

74.5

O

O

74.9

O

O

75.1

O

O

60.0

O

O

50.0

O

O

50.0

O

O

60.0

O

O

­ 52 ­

Search

DDLLPP PPrroojjeeccttoorr­­ UUsseerr”ss MMaannuuaall

SIGNAL

RESOLUTION

H-SYNC (KHZ)

V-SYNC (HZ)

COMPOSITE / S-VIDEO

COMPONENT

RGB (ANALOG)

DVI/ HDMITM (DIGITAL)

HDTV

720p

37.5

50.0

720p

45.0

60.0

1080i

33.8

60.0

1080i

28.1

50.0

1080p

67.5

60.0

1080p

56.3

50.0

O

O

O

O

O

O

O

O

O

O

O

O

O: Frequency supported

–: Frequency not supported

The native resolution of the panel is 1280 x 800. Resolution other than native resolution may display with uneven size of text or lines.

­ 53 ­

Search

DDLLPP PPrroojjeeccttoorr—-UUsseerr”ss MMaannuuaall

Projector Dimensions

335 mm

256 mm

102 mm

­ 54 ­

Search

DDLLPP PPrroojjeeccttoorr­­ UUsseerr”ss MMaannuuaall
REGULATORY COMPLIANCE
FCC Warning
This equipment has been tested and found to comply with the limits for a Class B digital device pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his/her own expense. Changes or modifications not expressly approved by the parties responsible for compliance could void the user’s authority to operate the equipment.
Canada
This class B digital apparatus complies with Canadian ICES-003.
Safety Certifications
FCC-B, UL, cUL, CB and CE.
­ 55 ­

Search

References

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals