MULLEN THREE Urban Utility Low Cab Forward Electric Vehicle User Guide

MULLEN THREE Urban Utility Low Cab Forward Electric Vehicle

Product Information

Specifications

• Model: 2023 Mullen THREE
• Exterior Master Power Switch: Red, located behind the cab
• Key and Remote: One standard key and one remote control switchblade
• Vehicle Battery: High-voltage battery system capable of delivering over 400 volts of direct current
• Charging Cable: Ensure good condition, no cracks or tears in the insulation, no corrosion or debris in the connection ports

Product Usage Instructions

Keys & Locks

• Each vehicle has one standard key and one remote control switchblade. The keys are used to unlock/lock the doors from outside the vehicle. The remote fob and the key are a single device.
• If locking the vehicle with a door ajar, the vehicle’s exterior lights will flash, and the horn will sound three times before locking.
• The vehicle will automatically relock itself if the vehicle is not entered within 30 seconds of using the remote to unlock the vehicle.

Starting the Vehicle

1. Turn ON the red exterior Master Power Switch located behind the cab (ON position is straight up and down / OFF position is parallel with the ground).
2. Ensure all doors are fully closed and fasten the seat belt.
3. Verify that the parking brake is engaged while the gear shift lever is in N (Neutral).
4. Adjust mirrors, steering wheel, and the driver seat for comfort.
5. Insert the key into the ignition switch, push in the brake pedal, and turn the ignition key to START.

The green READY Indicator illuminates when the vehicle is running. All other indicator lights should be off except for the Parking Brake indicator light.

Shifting the Vehicle

To change gears, the driver’s foot must be placed on the Brake Pedal or the gear will not engage.

1. Maintain pressure on the Brake Pedal.
2. Release the Parking Brake.
3. Move the Gear Selector to the desired gear.
4. Verify the selected gear on the instrument panel before proceeding.

Note : This Vehicle is NOT equipped with PARK on the Gear Selector. You must ALWAYS put your vehicle in Neutral and engage the Parking Brake every time you park.

Driver Controls Overview

Refer to pages 6 and 7 of the user manual for a detailed overview of driver controls.

High Voltage Safety & Information

Ensure the Charging Cable is in good condition:

1. Look for signs of cracks or tears in the insulation.
2. Ensure the connection ports are free of corrosion, water, or debris.
3. Do not modify the cable in any manner.
4. Do not use a Charging Cable with signs of damage.
5. Do not use extension cords with the Charging Cable.

Maintaining the State of Charge (SOC) between 20% and 90% will help improve the longevity of the high voltage battery. Charge the high voltage battery pack immediately if the SOC is below 20%. When charging, set the maximum state of charge at 90%.
Vehicle Battery range can vary depending on conditions such as climate, driving behavior, road conditions, etc.
This vehicle is equipped with a high-voltage battery system capable of delivering over 400 volts of direct current. The high voltage cables and connectors are orange in color for easier identification. Obey all caution labels that are attached to the vehicle. Failure to do so could lead to serious injury or death.

FAQ

Q: How many keys and remote controls are included with the vehicle?
A: Each vehicle comes with one standard key and one remote control switchblade.

Q: What happens if I lock the vehicle with a door ajar?
A: If you lock the vehicle with a door ajar, the vehicle’s exterior lights will flash, and the horn will sound three times before locking.

Q: Will the vehicle automatically relock itself if I don’t enter within 30 seconds of unlocking it with the remote?
A: Yes, the vehicle will automatically relock itself if it is not entered within 30 seconds of using the remote to unlock it.

Q: How do I start the vehicle?
A: To start the vehicle, follow these steps:

1. Turn ON the red exterior Master Power Switch located behind the cab.
2. Ensure all doors are fully closed and fasten the seat belt.
3. Verify that the parking brake is engaged while the gear shift lever is in N (Neutral).
4. Adjust mirrors, steering wheel, and the driver seat for comfort.
5. Insert the key into the ignition switch, push in the brake pedal, and turn the ignition key to START.

Q: How do I change gears?
A: To change gears, follow these steps:

1. Maintain pressure on the Brake Pedal.
2. Release the Parking Brake.
3. Move the Gear Selector to the desired gear.
4. Verify the selected gear on the instrument panel before proceeding.

Q: What should I do to ensure high voltage safety?
A: To ensure high voltage safety, follow these guidelines:

1. Ensure the Charging Cable is in good condition, with no cracks or tears in the insulation.
2. Make sure the connection ports are free of corrosion, water, or debris.
3. Do not modify the cable in any manner.
4. Do not use a Charging Cable with signs of damage.
5. Avoid using extension cords with the Charging Cable.

Preproduction model shown
Based on current specifications and subject to change.
Note : All figures are reference only and Mullen reserves the right to modify any and all information shown, without notification. Options subject to change.

Thank you for partnering with Mullen Automotive!
By operating a Mullen Urban Utility Low Cab Forward electric vehicle, you have joined a growing group of drivers who can fully appreciate the difference that a purpose-built vehicle can make.
Please take the time to familiarize yourself with this Quick Start Guide and the vehicle itself. The time you invest will ensure a great relationship with your Mullen electric vehicle. Always refer to the Mullen Vehicle Center website at https://www.mullenusa.com/mullenvehicle-center for the most up to date information on your vehicle.
Mullen Automotive Inc.
1055 W. Square Lake Rd. Troy, MI 48098
Thank you,
Your team at Mullen

KEYS & LOCKS

Each vehicle has one standard key and one remote control switchblade. The keys unlock/lock the doors from outside the vehicle. The remote fob and the key are a single device.
If locking the vehicle with a door ajar, the vehicle’s exterior lights will flash, and the horn will sound three times before locking.
The vehicle will automatically relock itself if the vehicle is not entered within 30 seconds of the remote’s use to unlock the vehicle.

STARTING THE VEHICLE

1. Turn ON the red exterior Master Power Switch located behind the cab (ON position is straight up and down / OFF position is parallel with the ground).
2. Ensure Doors are fully closed and fasten the Seat Belt.
3. Verify Parking Brake is engaged while Gear Shift Lever is in N (Neutral).
4. Adjust Mirrors, Steering Wheel and the Driver Seat for comfort.
5. Insert Key into the Ignition Switch, push in Brake Pedal and turn Ignition Key to START.

NOTICE

The green READY Indicator illuminates when the vehicle is running. All other indicator lights should be off except for the Parking Brake indicator light.

SHIFTING THE VEHICLE

To change gears, the driver’s foot must be placed on the Brake Pedal or the gear will not engage.

1. Maintain pressure on the Brake Pedal.
2. Release the Parking Brake.
3. Move the Gear Selector to the desired gear.
4. Verify the selected gear on the instrument panel before proceeding.

This Vehicle is NOT equipped with “PARK” on the Gear Selector. You must ALWAYS put your vehicle in Neutral and engage the Parking Brake every time you park.

DRIVER CONTROLS OVERVIEW

1. Steering Wheel
2. Horn Pad
3. Instrument Panel
4. Windshield Wiper & Washer Stalk
5. Ignition Switch
6. 12-Volt Accessory Outlet
7. Emergency Flasher Switch (Hazards)
8. Dimmer Switch for Lighted Controls
9. PTC – Heater Indicator Button
10. Infotainment
11. HVAC Control Pa nel (Heat, Ventilation, Air Conditioning & Defrost)
12. 3-Tier Dash Trays
13. Upper & Lower Glove Box Compartments
14. Windshield Washer Fluid Compartment
15. Passenger Seat
16. Flip Down Center Seat with Cup Holder
17. Fuse Block Access Panel
18. Gear Shifter
19. Pa rking Brake
20. Driver Seat
21. Steering Column Adjustment & Locking Handle
22. OBD Interface
23. Steering Wheel Radio Controls
24. Trip-Dashboard Menu Button, Turn Signal, Headlight, Running Light & Fog Lamp Stalk
25. Brake Fluid Compartment

HIGH VOLTAGE SAFETY & INFORMATION

Ensure the Charging Cable is in good condition.

1. Look for signs of cracks or tears in the insulation.
2. Ensure the connection ports are free of corrosion, water or debris.
3. Do not modify the cable in any manner.
4. Do not use a Charging Cable with signs of damage.
5. Do not use extension cords with the Charging Cable

Maintaining the State of Charge (SOC) between 20% and 90% will help improve the longevity of the high-voltage battery. Charge the high-voltage battery pack immediately if the SOC is below 20%. When charging, set the maximum state of charge at 90%
When not in use, the vehicle should be stored in temperatures between 32°F (0°C) and 113°F (45°C). If the vehicle will be parked for an extended period (e.g., 30 days), set the maximum SOC at 50%.
Vehicle Battery range can vary depending on conditions such as climate, driving behavior, road conditions, etc.
This vehicle is equipped with a high-voltage battery system capable of delivering over 400 volts of direct current.
The high voltage cables and connectors are orange in color for easier identification. Obey all caution labels that are attached to the vehicle. Failure to do so could lead to serious injury or death.
Do not touch high-voltage wiring, connectors or high-voltage parts, such as the inverter unit, high-voltage battery or drive motor. Touching, disassembling, removing or replacing high-voltage parts, cables and connectors can cause severe burns or electric shock that may result in serious injury or death.

HIGH VOLT CHARGING PROCEDURE

The Charging Port is located behind the cab near the passenger door (upper left corner of the passenger wheel well).

1. Engage the Parking Brake and remove the Ignition key.
2. The exterior red Master Power Switch located behind the cab must be left ON.
3. Release the Charging Port door latch.
4. Insert Charger. The instrument panel will display charging icon.
5. Close the charging door when complete to keep the port clean.

12-VOLT BATTERY CHARGING

1. Apply the Parking Brake.
2. Turn the Ignition Key switch to the START position.
3. The READY telltale will display on the dash cluster.
4. Let the vehicle sit in READY state for 2 (two) hours.

If the vehicle is parked for an extended period (e.g., 30 days), the 12V auxiliary battery may lose charge and fail to start the vehicle. To prevent the auxiliary battery from becoming depleted, periodically start the vehicle to allow the 12V battery to charge. To minimize the drain on the battery when the vehicle is parked and unused, make sure the doors are fully closed, door locked and all accessories are turned OFF. Also, make sure the exterior red Master shut off switch is turned OFF.

INSTRUMENT PANEL INDICATORS

1. Power Meter
2. Rear Fog Light
3. Left/ Right Turn Signal
4. Front Fog Light
5. Low State of Charge
6. High Beam
7. Driving Power Limit
8. Running Lamps
9. Motor Fault
10. Hazard Signal
11. Vehicle Ready
12. High Volt Charging
13. Vehicle Disable
14. Parking Brake
15. High Voltage Battery Fault
16. Seat Belt
17. Brake System Warning
18. Speedometer
19. ABS Warning
20. EBD Fault
21. Electronic Power Steering

LIFTING THE TILT CAB

1. Locate the cab release handles on the lower right exterior of the driver door.
2. Pull forward the gold latch release located behind the black handle.
3. While simultaneously holding the gold latch forward, grab the cab release lever and push upwards.
4. Once cab release lever is up, pull the safety release straight towards you.
5. Use the stationary black cab handle to lift the tilt cab upwards.
6. The safety latch will lock into place. Must add pin for additional safety.
7. To close cab: Remove pin, release safety lock and pull outward.
8. Pull down the tilt cab, lock into place and close the cab release lever.

When releasing safety latch, use caution. Moving parts can cause severe personal injury.

CHECKING CAB FLUIDS

1. Brake Fluid is located on driver dashboard side panel.
2. The windshield Washer Solvent is located on the passenger dashboard side panel.

CHECKING CHASSIS FLUIDS

Vehicle Fluids are located under the cab.

1. Power Steering Fluid
2. Coolant/Antifreeze
3. High Voltage Battery Coolant

CONTACT INFORMATION

Please visit us at www.mullenusa.com.
For Service, Parts, and Warranty Inquiries, please contact our Customer Solutions Support
Team at 248-988-4498.
Service email : service@mullenusa.com
Parts email : parts@mullenusa.com
Warranty email : warranty@mullenusa.com
Scan code to access vehicle manuals, guides and emergency response information. This label is located inside the charge port door and inside the glove compartment
These instructions apply to Mullen THREE vehicles. Certain devices, facilities or functions introduced in these instructions may not be installed on your vehicles due to different vehicle configurations. Mullen reserves the right to modify any and all information shown without notification. Options subject to change.

Part# AGIB-306X-AA
mullenusa.com/mullen-vehicle-center

References

• Shaping the Road Ahead in Electric Automobiles | Mullen
• Manual-Hub.com – Free PDF manuals!

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>