SHARP KI-N50 Air Purifier Humidifying Function Instruction Manual

KI-N50
KI-N50

KI-N50 Air Purifier Humidifying Function

** AIR PURIFIER
with Humidifying Function
OPERATION MANUAL**

**INTELLECTUAL PROPERTY
RIGHTS FOR THIS PRODUCT
*** The number in this technology mark indicates an approximate number of ions supplied into air of 1 cm³ , which is measured around the center of a room applicable floor area (at 1.2 m height above the floor) when the product is placed close to a wall at the MED mode setting.
Thank you for purchasing this SHARP Air Purifier.
Please read this manual carefully before using the product.
This manual should be kept in a safe place for handy reference.

Please Read Before Operating Your Air Purifier
The air purifier draws in room air through the air inlet, circulates it through a Pre-Filter, a Deodorizing Filter and a HEPA Filter inside the product, and then discharges it through the air outlet.
The HEPA Filter can remove 99.97% of dust particles as small as 0.3 microns that pass through the filter and also helps absorb odors.
The Deodorizing Filter gradually absorbs odors as they pass through the filter.
Some odors absorbed by the filters will break down over time, causing additional odors. Depending on usage conditions, and especially if the product is used in environments significantly more severe than a normal household, these odors may become noticeable  sooner than expected. If these odors persist, replace the filters.![SHARP KI-N50 Air Purifier Humidifying Function

• Figure 1](https://manuals.plus/wp-content/uploads/2024/01/SHARP-KI-N50-Air- Purifier-Humidifying-Function-Figure-1.png)

  • The illustration in this instruction manual is KI-N40.

When minerals in tap water adhere to the filters and become hard and white, they absorb odors in the room that can cause the emission of an unpleasant odor when the Humidifying Filter is dry. (Varies depending on water quality and other environmental factors.)
If this occurs, perform the Humidifying Filter maintenance. (Page 20)

NOTE

• The air purifier is designed to remove air-suspended dust and the odors.
  The air purifier is not designed to remove harmful gases such as carbon monoxide contained in cigarette smoke.
  The air purifier may not completely remove an odor if the source of the odor is still present.

FEATURES

A unique Combination of Air Treatment Technologies Triple Filtration System + Humidification + Plasmacluster

Plasmacluster
High Density Plasmacluster 25000
The higher the PCI density is, the more effective PCI has.
By emitting a balance of positive and negative ions, Plasmacluster air treatment is a natural process. ****

Triple Filtration System + Humidification
TRAPS DUST
Pre-filter traps dust larger than approx 240 micron particles.
DECREASES ODORS
Deodorizing filter absorbs many common household odors.
REDUCES TINY DUST, POLLEN & MOLD
HEPA filter traps 99.97% of particles as small as 0.3 microns.
HUMIDIFIES
Controls humidity by sensing temperature and humidity automatically.
Unique Airflow
Powerful air suction and unique airflow quickly and efficiently collect dust and other particles.Faster airflow at a 20º angle causes dust to be collected at lower levels in the room for more effective cleaning.
Plasmacluster can remove static electricity and can thus prevent dust from attaching to walls and other surfaces.

Wi-Fi Function

• Confirms that the air quality of the room has become clean visually.
• Controls the product through smart devices such as a remote control.
• Proposes optimal timing for filter exchange.

IMPORTANT SAFETY INSTRUCTIONS

READ AND SAVE THESE INSTRUCTIONS before using this product.
When using electrical appliances, basic safety precautions should always be followed to reduce the risk of fire, electric shock, and injury to persons, including the following:

WARNING

1. Read all instructions before using the product.

2. Use the product only for intended household use as described in this manual. Any other use not recommended by the manufacturer may cause fire, electric shock, or injury to persons.

3. This appliance is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction concerning use of the appliance by a person responsible for their safety. Children should be supervised to ensure they do not play with the appliance.

4. Never operate the product if the power cord or plug is damaged or the product is malfunctioning or damaged.

5. If the power cord or plug is damaged, it must be replaced by the manufacturer, its service agent, a Sharp authorized Service Center or similarly qualified persons in order to avoid a hazard. Contact the nearest Service Center for any problems, adjustments, or repairs.

6. Do not repair or disassemble the product yourself.

7. Follow the instructions “a” to “h” below for the power cord or plug. If not, a shortcircuit, excessive heat, electric shock or fire may result.
   a. Use only AC 220-240 volt outlet.
   b. Do not use the product if the power cord or plug is damaged or theconnection to the wall outlet is loose or damaged.
   c. Always turn off the product beforeunplugging the power plug.
   d. Always unplug the product in the following cases.
   • Before moving the product.
   • When replacing the filter. (Even when opening the Back Panel.)
   • When refilling water.
   • Before maintenance of the product.
   • When the product is not in use.
   e. Be sure to pull the power plug and not the power cord.
   f. Do not touch the power plug with wet hands when inserting or unplugging from the wall outlet.
   g. Periodically remove dust from the power plug.
   h. Always observe the following so as to not damage the power cord.
   • Do not damage cord with Caster Wheels when moving the product.
   • Do not run cord under carpeting.
   Do not cover the power cord with throw rugs, runners, or similar coverings.
   • Do not put heavy things on the power cord or pinch it.
   • Do not run the power cord under furniture or other appliances.
   • Run the power cord away from traffic area and where it will not be tripped over.

8. Do not use this product near gas appliances, fire places, candle fire, incense or sparks from lit cigarettes.
   When the product is operated with gas appliances in the same room ventilate a room periodically, otherwise it may cause carbon monoxide poisoning.

9. Do not operate the product in a room with flammable gas, such as oily residue or chemical fumes.

10. Do not expose the product to rain, or use near water, in a bathroom, laundry area or other damp location.

11. Do not insert fingers or foreign objects into the air inlets or air outlets.

12. Do not look into the air outlets.

13. Do not drink the water in the Water Tank or Humidifying Tray.

14. Replace the water in the Water Tank daily with fresh tap water, and regularly clean the Water Tank and HumidifyingTray.
    When the product is not in use, dispose of the water in the Water Tank and Humidifying Tray. Leaving water in the Water Tank or Humidifying Tray can cause mold, bacteria, and bad odors.
    In rare cases, such bacteria can be a health hazard.

NOTE
– Radio or TV Interference If the product should cause interference to radio or television reception, try to correct the interference by one or more of the following measures:

1. Reorient or relocate the receiving antenna.
2. Increase the separation between the product and radio/TV receiver.
3. Connect the product into an outlet on a circuit different from that to which the receiver is connected.
4. Consult the dealer or an experienced radio/TV technician for help.

CAUTIONS CONCERNING INSTALLATION

1. Place the product on a level and stable surface with sufficient air circulation.
   When placed on heavy carpet, the product may vibrate slightly.
   Place the product on a level surface to avoid water leakage from the Water Tank and Humidifying Tray.

2. Avoid a location where the sensors areexposed to direct breeze or draft if the product has sensors. The product may not operate properly.

3. Avoid use in locations where furniture, fabrics, or other items may come in contact with and restrict the air inlets and/or outlets.

4. Avoid locations exposed to direct sunlight. It may cause the product to change shape or color.

5. Avoid locations where the product is exposed to condensation or drastic changes in temperature. Use under appropriate conditions between 0ºC – 35ºC.

6. Avoid use in locations where greasy or oily smoke is generated (such as in a kitchen, etc.). The Main Body surface may crack and the sensors may malfunction as a result.

7. The dust collecting ability of the product is effective even when the product is up to 3 cm from the wall, but the surrounding walls or floor may get dirty.
   Please place the product at a distance from the wall.
   The wall directly behind the air outlets and the floor or rug on which the product is placed may become dirty over time. When using the product for an extended period of time at the same location, periodically clean the walls, the floor or the rug.

8. Do not place the product near or on hot objects, such as stoves or heaters, or where it may come into contact with steam.

CAUTIONS CONCERNING THE FILTER

1. Follow the instructions in this manual for filter installation and maintenance (Page 9, 22).
2. Take out the filters from the plastic bag before placing the filters in the Main Body.
3. Do not operate the product without the filters properly installed.
4. Do not wash and reuse the HEPA Filter and the Deodorizing Filter. Washing will not improve filter performance and can also cause electric shock or operating malfunctions.
5. Do not operate the product in a room where aerosol insecticides are present.
   It may cause the insecticide odor to remain in the product and be emitted from the air outlets.

CAUTIONS CONCERNING OPERATION

1. Do not block the air inlets or air outlets.
2. Always operate the product in an upright position.
3. When carrying the product, first remove the Water Tank and Humidifying Tray so as not to spill the water, and then hold the product by the handles on both  sides.
4. Always lift up the product when moving it on easily damaged flooring, an uneven surface, or carpet.
5. Do not change the direction of the product while moving using the Caster Wheels.
6. When moving the product by its Caster Wheels, move it slowly and in a horizontal direction.
7. Do not operate the product without the Water Tank or Humidifying Tray properly installed.
8. Be careful not to catch your fingers when removing or installing the Water Tan k .
9. When refilling the Water Tank, make sure no water leaks from the Water Tan k .
10. Be sure to wipe off any excess water on the outside of the Water Tank.
11. Do not use hot water (40ºC or more), chemical agents, aromatic substances, dirty water, or other damaging substances. Doing so can deform the product or cause it to malfunction.
12. Use only fresh tap water. Using other water sources risks the growth of mold, fungi, or bacteria.
13. Do not shake the Water Tank while holding the Tank Handle.

CAUTIONS CONCERNING MAINTENANCE

1. Follow the instructions in this manual for maintenance (Page 18 – 23).

2. Clean the exterior with a soft cloth only.

3. Do not use detergents other than what is mentioned in this manual (Page 19, 21). Do not use volatile fluids and/or detergents.
   The Main Body surface may be damaged or cracked with strong corrosive cleansers, benzine, paint thinner, polishing powder or grease.
   The Humidifying Tray may experience deformation, tarnishing, cracking (water leakage). In addition, the sensors may malfunction as a result if the product has sensors.

4. Do not scrub the Back Panel (Pre-Filter) hard during its maintenance.

5. The frequency of descaling maintenance will depend on the hardness of and the impurities in the water that you use; the harder the water the more often descaling will be necessary.

6. Do not remove the Humidifier Float and the Roller. If the Humidifier Float and the Roller come off, refer to page 21.

7. When replacing filters or any accessories, use specified parts in this manual.

SAFETY / PRECAUTIONS OF THE Wi-Fi FUNCTION
WARNING
When remotely controlling the air purifier
In case of remote operation from outside, you may not be able to check the air purifier’s current condition or the area around it and the situation concerning anyone possibly staying there, so please adequately confirm safety before use.

1. Make sure the electric plug is fully inserted into a power socket, and there is no dust on the plug or in the socket hole. (It may cause heat, combustion, fire, etc., due to poor contact or contact failure.)
2. Make sure beforehand to check the ambient environment of the product, because the air flow from the product may cause unexpected phenomenon (such as unstable items falling down), and this may result in fires, wounds, and defacement of house belongings.

CAUTION FOR USE

1. Agreement with “Terms of Service” is required to use App.
2. Ensure that the App is up to date.
3. Screens and illustrations in this book are for explanation, there are some differences compared to the actual product.
4. In the case of bad connection, the App may not be able to control the air purifier. The current operation of the air purifier may not be accurately reflected on the App.
5. Locking smart device display is recommended to avoid incorrect operation.
6. Communication charges will occur by the download and use of the App.

CAUTION FOR Wi-Fi
Caution for usage of electrical wave

1. Usage of the application is not guaranteed under the following environment:
   a. Near Bluetooth® wireless communications device using the same frequency (2.4GHz) as this product.
   *The Bluetooth® word mark is a registered trademark owned by Bluetooth SIG,. Inc.
   b. Near a product which emits magnetic field. (e.g. microwave oven)
   c. Near a place with static electricity.
   d. Near a place where radio disturbance occurs.
   e. Near other wireless communications devices.

2. Wireless connection and performance cannot be guaranteed for all routers or environmental conditions.
   At the following places, Wi-Fi connection might be unstable:
   a. Inside of a building made with concrete, reinforcing steel or metal.
   b. Near an obstruction.
   c. Near wireless communications devices using the same frequency.
   3. Wi-Fi of this product corresponds to channel 1 – 13. It’s not available to communicate with the routers set up with other channels.

Caution for personal information
(related to Security)

1. Using Wi-Fi device has the possibility of interception regardless of the secret code setting.
2. Make sure to use the network under your management.
3. Initialize the device when sold, disposed of or handed over from/to a third person.
   See page 16 on how to initialize.

PART NAMES

LIGHT SENSOR
When the Light Control (Display Brightness) is set to “Auto”, the Display and Cleanliness Indicator will automatically switch ON or OFF based on room brightness. (Page 15)
NOTE
Detection range of Light Sensor
Do not install the product in the following places. The Light Sensor may not sense correctly.

1| Sensor (Internal)
Odor / Temperature / Humidity
---|---
2| Light Sensor
3| Power ON/OFF Button
4| SHARP COCORO AIR Button, Lamp (White)
5| Mode Button, Lamps (White)
6| Humidify ON/OFF Button, Lamp (White)
Filter Reset Button (Press 3 sec.) 3
7| Filter Maintenance Lamp (Orange)
8| HAZE Button, Lamp (White)
9| Wi-Fi Button, Lamp (White)
Illuminates when air purifier is connected to a router.
10| Timer Lamp (White) 1
11| Switching Display Button
Child-Lock Button (Press 3 sec.) 3
12| Child-Lock Lamp (White)
13| Unit Replacement Lamp (Red)
14| Cleanliness Indicator
Indicates the air purity of the room in 5 levels with color changes.
15| PM2.5 Indicator (White)
Indicates the Sensitive Dust Sensor detects microscopic dust.
16| Dust Indicator (White)
Indicates the Sensitive Dust Sensor detects usual dust.
17| Odor Indicator (White)
Indicates the Odor Sensor detects odors.
18| Cloud Service Indicator (White) 1
Illuminates when air purifier is connected to Sharp’s cloud service.
19| Plasmacluster Ion Indicator (Blue)
20
| Humidifying Indicator
White: Humidify ON
OFF: Humidify OFF
Red (Flashing) : the product needs water
21| *Display2
• Temperature
Temperature 0º C to 50º C is displayed. • Humidity
Humidity 25% to 75% is displayed.
• PM2.5 Concentration* 4
PM2.5 10 µg/m³ (micrograms per cubic meter air) to 499 µg/m³ is displayed.

1: The lamps of No.10 and 18 light up only when using the App.
2: The displayed numbers are approximate.
3: Press and hold 3 seconds or longer.
4: Particulate matter, particles with diameter of size 2.5 micrometers or less.

(Plasmacluster Ion Generating Unit)
7| Unit Cleaning Brush
8| Unit Cover
9| Tank Handle
10| Water Tank
11| Tank Cap
12| Humidifying Filter
13| Humidifying Tray
14| Tray Panel
15| Humidifier Float
16| Roller
17| Air Outlet (Back)
18| Handle (2 Locations)
19| Sensor Filter / Sensor (Internal) Sensitive Dust
20| Power Cord, Power Plug (Shape of power plug depends on country.)
21| HEPA Filter
22| Deodorizing Filter
23| Back Panel
24| Air Inlet**

• The Unit refers to Plasmacluster Ion Generating Unit. (The same as below.)

PREPARATION

• To maintain the quality of the filter, it is installed in the product and packaged in a plastic bag.
• Be sure to stop operation and unplug the product before filter installation or replacement.

FILTER INSTALLATION

1. Remove the Back Panel.
2. Take out the filters from the plastic bag.
3. Install the filters in the correct order as shown.
4. Install the Back Panel.

NOTE

• It is recommended that you note down the date when the filters were replaced for future reference.
• Do not operate the product without the filters.

REFILLING THE WATER TANK

1. Remove the Water Tank.
2. Fill the Water Tank with the tap water.
3. To prevent leaks, securely tighten the Tank Cap.
4. Install the Water Tank.

OPERATION

Wi-Fi SETTINGS
BEFORE YOU BEGIN

• By connecting your air purifier with your smart device, you can enjoy greater convenience.

Ensure your smart device is connected to a 2.4 GHz Wi-Fi Network.
Wi-Fi Protected Setup (WPS) Access Point (Router)

• The recommended encryption method is WPA2 (AES).

Ensure your smart device meets minimum software requirements (as of October 2022) :

• Smartphones / tablets of Android 8 or later
• iPhones, iPod touch, iPads of iOS 12 or later Product Wi-Fi specifications
• Wireless LAN: IEEE802.11b/g/n
• Frequency range: 2.4GHz frequency band Trademarks
• “Wi-Fi® ” is a registered trademark of Wi-Fi Alliance®.
• “Android” is the trademark of Google Inc.
• “iPhone”, “iPod touch”, “iPad” are the registered trademarks or trademarks of Apple Inc.
• The other company names, corporate names, product names mentioned in the handling instructions are trademarks and registered trademarks of each company.

INITIAL SET UP
NOTE

• When pairing the smart device to the air purifier, please ensure they are both connected to the same router.

1. DOWNLOAD & SIGN UP
   1. Install the designated App in your smart device.• Available to download from the Apple Store or Google Play.
   https://cboard.cloudlabs.sharp.co.jp/smartapp_asean/download/air/
   2. Connect your smart device to the router and launch the App.
   Follow instructions on the App.
   i. Review the “Terms of Service”.
   ii. Sign in using your Sharp account (SHARP ID).
   • If you do not have a SHARP ID, please register to create a SHARP ID.
   iii. Enter a name for your smart device.

2. CONNECTION OF THE AIR PURIFIER AND A ROUTER
   NOTE
   • If you have stealth settings or MAC filtering settings on the router, please cancel them.
   • The product network ID is displayed as “AP-SHARP-XX” (where XX is a 2-digit number below the product MAC address).
   1. Tap “ ” at the upper left part of the “Home” screen, and select “Register Device” “Connection with a router”.Follow instructions on the App.
   • If the Wi-Fi Lamp lights up after the notification sound, the connection is successfully completed.

3. CONNECTION BETWEEN THE AIR PURIFIER AND A SMART DEVICE
   1. Tap “Register” for the air purifier you would like to register.• If you do not see the screen above, tap “ ” at the “Home” screen, and select “Register Device” “Already connected with a router”.

4. Follow instructions on the App.
   • If the Wi-Fi Lamp lights up after the notification sound, the connection is successfully completed. The INITIAL SET UP is completed.

How to set Wi-Fi ON / OFF after completing the INITIAL SET UP
If you would like to turn the Wi-Fi OFF:

NOTE

• Turning the Wi-Fi off will result in not being able to control the air purifier with the designated App.

If you would like to turn the Wi-Fi ON again:
(How to restore the Wi-Fi connection to the original network.)

The Wi-Fi Lamp will flash after you press the Wi-Fi Button. And within about 3 minutes, you will hear four short beeps. Some time after this beep sounds, the Wi-Fi Lamp lights up and the Wi-Fi connection will be restored to the original network.
The designated App can now be used again to control the Air Purifier.

NOTE

• Wi-Fi ON / OFF can also be set from
  “ : Wi-Fi adapter ON/OFF”. (Page 14, 16)
  In this case, Wi-Fi connection with the router will be automatically restored.

• Reconnection to the Wireless Router may take a few minutes to complete, after turning Wi-Fi on again.

START/STOP

NOTE

• When the product starts operating the operation starts in the previous mode it was operated in.

SHARP COCORO AIR MODE

When the product is connected to Sharp Cloud
Sharp Cloud will analyze and set the optimal operation for your room based on the information retrieved from sensors on the product and your usage records.

When the product is not connected to Sharp Cloud
The fan speed and the humidification ON / OFF are automatically controlled depending on the six detection. (PM2.5 / Usual dust / Odor / Temperature / Humidity / Light)

NOTE

• If you press the Humidify ON/OFF Button, the operation mode will change to (AUTO).

HAZE MODE
Operates at HIGH fan speed for 60 minutes and then alternates between Low and High level for 20 minutes each. 10 minutes: Max High fan level
50 minutes: High fan level
20 minutes: Low fan level
20 minutes: High fan level

NOTE

• The Plasmacluster ion cannot be turned “OFF”.

SELECT AIR VOLUME AND MODE AUTO:
The fan speed is automatically switched depending on the amount of impurities in the air.
You can select humidification ON / OFF.
POLLEN:
The Sensitive Dust Sensor sensitivity is automatically increased and the Sensitive Dust Sensor quickly detects impurities such as dust and pollen and cleans the air powerfully.
SLEEP:
The product will operate quietly, and the fan speed will automatically depending on the amount of impurities in the air and room brightness.
When the Light Control is set to “Auto”, the Display and Cleanliness Indicator will automatically go off.

HUMIDIFICATION SETTING

NOTE

• When operating with Humidification ON in the modes in the table below, the productautomatically controls humidity by sensing temperature and humidity. (Except MAX / MED / LOW mode.)

• Except MAX / MED / LOW / SLEEP

SWITCH DISPLAY

CHILD LOCK
The operation panel will be locked.
(with the product ON or OFF)

NOTE

• It is possible to turn Wi-Fi off while in Child Lock Mode.

WEEKLY SCHEDULER: APP ONLY
ON TIMER (or OFF TIMER)
You can set a weekly scheduler for the air purifier to start on a specific mode (or to stop operation) on a specific day and time.
The Timer Lamp will turn on while there is a schedule set.

HOW TO CHANGE VARIOUS SETTINGS

• You can change the product and Wi-Fi functions on page 15 – 18.

1. Turn the product OFF.

2. 

3. Select “Function number (F1-F7 or A1-A8)” on page 15 – 18.

4. When on Wi-Fi setting
   Refer to page 16 – 18 for the details of each function.
   When on Product setting
   Select “Setting number (01 – 03)” on page 15.

5. Finish the setting.

PRODUCT FUNCTIONS (F1-F7)

Light Control
You can select the brightness of the Display and Cleanliness Indicator.| OFF
When set to “OFF”, the “Dim” light illuminates for 8 seconds after operation starts and then the light goes off.
However, some indicators that need notification will remain dim.
Dim
Auto (default)
Light automatically switches ON or OFF based on room brightness.
• Room is bright: light is ON
• Room is dark: light is OFF
Even though the room is bright, the light will turn off when operating in sleep mode.
Plasmacluster Ion ON/OFF| OFF
ON (default)
Auto Restart
If the product is unplugged or if there is a power failure, the product will resume operation with the previous settings after power is restored.| Cancellation
ON (default)
 Adjusting sensor sensitivity (F4 – F6)
Light Sensor
Sensitive Dust Sensor
Odor Sensor| Low
Standard (default)
High
Sound Indicator Setting
You can set the product to make a beeping sound when the Water Tank is empty.| Cancellation (default)
ON

Wi-Fi FUNCTIONS (A1-A8)

2. Press ” SHARP COCORO AIR ” Button to select Setting “ ” or “ “.
3. Complete NOTE
• When Setting number (“ ” or “ “) is changed, the square rotates on the display until the setting is completed. When setting is completed, “ ” is displayed.

Wi-Fi connection with a router (with the WPS Button)| 1. Select “ ” by following Steps 1 – 3 on page 14.
2. After “ ” is displayed, press the WPS (Wi-Fi Protected Setup) Button of the router. Once connected, receiver level will be displayed.
A connection error is occuring if “ ” is displayed. Please confirm that the router is operating correctly and try again.
3. Complete
Initialization of Wi-Fi function| 1. Select “ ” by following Steps 1 – 3 on page 14.
2. After “ ” is displayed press “Mode” Button.
An error is occurring if “ ” is displayed. Please try again.3. CompleteNOTE
• Please delete the device registration from the App when initializing the air purifier which is already connected to the Wi-Fi.
Confirmation of MAC address| 1. Select “ ” by following Steps 1 – 3 on page 14.
2. Press “SHARP COCORO AIR” Button to display MAC address.
For example:
In case MAC address is “12:34:56:AB:CD:EF”.3. Complete
Display Wi-Fi network status| 1. Select “ ” by following Steps 1 – 3 on page 14.
2. After displaying “–” for a few seconds, the network status of the Wi-Fi adapter will be displayed.3. Complete
 Wi-Fi connection with a router (without the WPS Button)
– AP (Access Point) mode –| 1. Select “ ” by following the Steps 1 – 3 on page 14.
2.  Perform Wi-Fi connection of the air purifier and the router based
on the App screen.
Refer to the App for further operations.Display while setting the connection between the product and the router.
Once connected, the receiver level will be displayed.
A connection error is occuring if “ ” is displayed. Please confirm the router and try again.

CARE AND MAINTENANCE

CARE

• To maintain optimum performance of this air purifier, please clean the product including the filter periodically.
• Be sure to stop operation and unplug the product before any maintenance or replacing accessories.

FILTER MAINTENANCE LAMP
When the cumulative operation period or the water containing period is more than approximately 720 hours, the Filter Maintenance Lamp will turn on.

• It will not calculate the time when the product is unplugged.
• 30 days × 24 hours = 720 hours

This is a reminder to perform the maintenance for the Humidifying Filter and Tray, Main Body, Back Panel, and Sensors.
After maintenance, connect the power plug to the wall outlet and press Power ON/OFF Button, then press and hold the Filter Reset Button for 3 seconds to reset the Filter Maintenance Lamp.

WATER TANK
Rinse the inside with water. NOTE How to Clean Hard-to-Remove Dirt.
Clean the inside of the Water Tank with a soft sponge and the Tank Cap with a cotton swab or toothbrush.

MAIN BODY / BACK PANEL / SENSORS
Wipe with a dry, soft cloth. Remove the dust gently with a cleaning tool such as a vacuum cleaner.

NOTE
• Do not apply excessive pressure when scrubbing the Back Panel.
NOTE
How to Clean Hard-to-Remove Dirt.

Back Panel

1. Add a small amount of mild kitchen detergent to water and soak for about 10 minutes.
2. Rinse off the mild kitchen detergent with clean water.
3. Completely dry the filter in a well-ventilated area.

Sensor Filter

1. Remove the Back Panel.
2. Remove the Sensor Filter.
3. If the Sensor Filter is very dirty, wash it with water and dry it thoroughly.

HUMIDIFYING FILTER / HUMIDIFYING TRAY
REPLACEMENT AND MAINTENANCE CYCLE

Parts Name| Maintenance Cycle| Max Service Life| Replacement Filter Model
---|---|---|---
Humidifying Filter| When odor emanates from the air outlet, or once a month.| 10 years*1| FZ-J1XMFE

MAINTENANCE

1. Remove the Humidifying Filter and Tray.

2. Rinse with plenty of water.
   • Do not remove the Humidifier Float. If it comes off, refer to page 21.
   • Refer to page 21 on how to clean the Humidifying Filter when it is very dirty.

3. Attach the Humidifying Filter and Tray.
   • After maintenance, correctly reattach the parts.

REPLACEMENT
See this page for directions on how to install the filter when replacing.

• Please consult your dealer for purchase of replacement filter.
• Use only filter designed for this product.

It is recommended that you note down the date when the filters were replaced for future reference.

Disposal of Filters
Please dispose of the replaced filter according to the local disposal laws and regulations.
Humidifying Filter materials: Polyester, Rayon

FZ-J1XMFE
(1 unit)

• Do not dispose the Filter Frame.

NOTE How to Clean Hard-to-Remove Dirt.

| Mild Kitchen Detergent
(only Humidifying tray)| Citric Acid
(available at some drugstores)| 100% Bottled Lemon Juice with No Pulp
---|---|---|---
1| 1. Fill the tray half-way with water.
2. Add a small amount of mild kitchen detergent.| 2 1/2 cups of water| 3 cups of water
2| Soak for 30 minutes.| Soak for 30 minutes.
(When using lemon juice as your descaling solution, allow for more soak time.)
3| Rinse off the mild kitchen detergent or the descaling solution with clean water.

NOTE How to install the Humidifier Float.
Humidifier Float 

HEPA FILTER / DEODORIZING FILTER
REPLACEMENT AND MAINTENANCE CYCLE

Filter Name| Maintenance Cycle| Max Service Life| Replacement Filter Model
---|---|---|---
HEPA Filter| Whenever dust accumulates, when odor emanates from the air outlet, or once a month.| 10 years*1, 2| FZ-D40HFE
Deodorizing Filter| FZ-D40DFE (Only KI-N40) FZ-G40DFE (Only KI-N50)

1: According to Japan Electrical Manufacturers’ Association JEM 1467, the Max service life is based on the equivalent condition of the smoke from 5 cigarettes per day whereby the dust collection/deodorization power is reduced by half compared with that of a new filter. It is recommended to replace the filter more frequently under more severe conditions.
2: Designated App notifies when each replacement part should be replaced according to usage.
Filter life varies depending on the room environment, usage conditions, and location of the product. We recommend replacing the filter more frequently if the product is used in conditions significantly more severe (PM2.5 etc.,) than a normal household.J

MAINTENANCE
Remove the dust on the filters.

NOTE

• Do not wash the filters. Do not expose to sunlight (Otherwise these filters may lose their efficacy.)

HEPA FILTER
Maintain and clean only the tagged surface. Do not clean the opposite surface.
The filter is fragile, so be careful not to apply too much pressure. DEODORIZING FILTER
Both surfaces can be maintained and cleaned.
The filter is fragile, so be careful not to apply too much pressure.Some odors absorbed by the filters will break down over time, causing additional odors. Depending on usage conditions, and especially if the product is used in environments significantly more severe than a normal household, these odors may become noticeable sooner than expected.
Replace the filter in those cases or if dust is unable to be removed after maintenance.

REPLACEMENT
See page 9 for directions on how to install the filter when replacing.

• Please consult your dealer for purchase of replacement filter.
• Use only the filter designed for this product.

It is recommended that you note down the date when the filters were replaced for future reference.

Disposal of Filters
Please dispose of the replaced filter according to the local disposal laws and regulations.
HEPA Filter materials:
Polypropylene, Polyethylene
Deodorizing Filter materials:
(Only KI-N40)
Polypropylene, Polyester, Activated Carbon
(Only KI-N50)
Paper, ABS Resin

NOTE

• Do not wash and reuse replaced filter.

PLASMACLUSTER ION GENERATING UNIT (Electrode Section)
REPLACEMENT AND MAINTENANCE CYCLE

Parts Name| Maintenance Cycle| Max Service Life| Replacement Model
---|---|---|---
Plasmacluster Ion Generating Unit1| Every 6 months or more often if necessary| 19,000 hours2,3| IZ-C90ME

1: In the following, “Plasmacluster Ion Generating Unit” is abbreviated as “Unit”.
2: The replacement time will be announced by the Unit Replacement lamp.
*3: Designated App notifies when each replacement part should be replaced according to usage.

MAINTENANCE

1. Remove the Unit Cover, and pull out the Unit Holder.
2. Remove dusts from the Electrode Section.
3. Insert the Unit Holder in the product, and install the Unit Cover.

NOTE

• Do not clean with anything other than the Unit Cleaning Brush. Doing so could lead to failures in the Unit.
• A bent electrode could be cut off and dropped during the cleaning process, but it will not change the performance.
• Do not touch the electrode directly. Doing so could lead to pain/itching.
• Do not transform the Electrode Section. Doing so can damage it.
• Do not touch the Connection Terminals. Doing so can damage them.

REPLACEMENT
Unit Replacement lamp
When the total operation time exceeds 17,500 hours, the Unit Replacement Lamp will flash to indicate that the Unit needs replacement.

17,500 hours
UNIT Flashes slowly| Replace the Unit.
19,000 hours
UNIT Flashes quickly| No Plasmacluster ions will be released by the Unit.

• The replacement time is not related to the selected operation mode.

How to replace the Unit

• Please consult your dealer for purchase of a replacement Unit.
• Use only the Unit designed for this product.

1. Remove the claw of Unit Holder (1), and remove the Unit ( 2 ).
2. Attach the New Unit. • When the Unit has been replaced with a new part, the timer will be reset and return to 19,000 hours.

Disposal of the Unit
Please dispose of the used Unit according to the local disposal laws and regulations.
Materials:
Polybutylene Terephthalate, electronic parts.

TROUBLESHOOTING

• Before calling for service, please review the Troubleshooting list below, since the problem may not be the product malfunction.

ABOUT THE PRODUCT
Odor and smoke persist.

• Check the filters. If they appear to be extremely dirty, clean or replace them.

Air discharged from the product has an odor.

• Check to see if the filters are extremely dirty.
• Clean or replace the filters.
• Use only fresh tap water. Using other water sources risks the growth of mold, fungi, or bacteria.

The product does not operate when cigarette smoke is in the air.

• Make sure the product is installed in a location in which the sensors can detect cigarette smoke.
• Check to see if the Sensitive Dust Sensor openings are blocked or clogged. If they are blocked or clogged, clean the Sensor Filter or the Back Panel.

Smell from a new product and/or filter.

• Immediately after removing the plastic bag, a slight odor may occur. This odor is not harmful for filter performance or human exposure.

The product makes a clicking or ticking sound.

• The product may make clicking or ticking sounds when it is generating ions.

The Cleanliness Indicator is blue even when the air is not clean.

• The air may have been dirty when the product was plugged in. Unplug the product, wait one minute, and then plug the product in again.

The Cleanliness Indicator is red even when the air is clean.

• Dirty or clogged Sensitive Dust Sensor openings interfere with sensor operation. Gently clean the Sensor Filter or the Back Panel.

The Cleanliness Indicator changes color frequently.

• The Cleanliness Indicator automatically changes color when the Sensitive Dust Sensor and Odor Sensor detect impurities. If you are concerned about the change, you can change sensor sensitivity. (Page 14, 15)

Filter Maintenance Lamp is on.

• Whenever after performing maintenance or replacing the Humidifying Filter, connect the power cord to an outlet and then press the Filter Reset Button for more than 3 seconds. (Page 19)

The Display goes off.

• When the Light Control is set to “Auto”, the light automatically turns off when the room is dark or operating in sleep mode. Moreover, when the Light Control is set to “OFF”, the light is always off.
  If you do not want the light to be off, set the Light Control to the “Dim” setting. (Page 14, 15)

The Display does not match the weather report or another hygrometer or thermometer in the room.

• Outdoor and indoor as well as the home environment (the volume of traffic nearby, number of stories in a home, etc.) may cause a reading different than those data.
• There is a difference in the level within the same room.

The Humidify Indicator on the Display does not light up when the Water Tank is empty.

• The room has reached the appropriate level of humidity and has stopped humidifying.
• Check the Humidifier Float for impurities. Clean the Humidifying Tray. Make sure that the product is on a level surface.

The water level in the Water Tank does not decrease or decreases slowly.

• Check to see if the Humidifying Tray and Water Tank is correctly installed.
• Check the Humidifying Filter. If the filter is extremely dirty, clean or replace it.

is displayed.

• Make sure that the Humidifying Filter, Humidifying Tray and Roller are properly installed, and then turn the power to ON again.

is displayed.

• Make sure the Plasmacluster Ion Generating Unit has been inserted properly.
  Pull out the Plasmacluster Ion Generating Unit and insert it to the end again, and then carry out the operation again.

One of the following is displayed.

• Unplug the product, wait one minute, and then plug the product in again.

ABOUT THE Wi-Fi FUNCTION
The Wi-Fi connection of the air purifier and the router is not working.

• Check the specifications of the router in use.
• Adjust the router and antenna direction, move the router and antenna closer, and so on. After that, reswitch to turn on the router and perform the INITIAL SET UP again.

The connection between the air purifier and your smart device cannot be established.

• Are the air purifier and your smart device connected to the same router?
  Connect the air purifier and your smart device to the same router.
  If you still can’t connect, try connecting your smart device to the 2.4GHz band of the router.

• Is the total number of smart devices being in use exceeding the maximum number for registration on one air purifier?
  The maximum number of smart devices that can be registered on one air purifier is 10.

• Is the total number of products (air conditioners, air purifiers, etc.) to be registered with one smart device exceeding the maximum designated number?
  The maximum number of products to be registered with one smart device is 30.

Remote operation from a smart device cannot be performed.

• Is the Wi-Fi Lamp of the air purifier on?
    If the Wi-Fi Lamp is off, please perform “A1: Wi-Fi adapter ON/OFF” to turn on the product Wi-Fi. (Page 16)

• Has the connection between the air purifier and your smart device been completed?
   Set up the connection between the air purifier and your smart device. (Page

When changing the router

• It is necessary to reconnect the air purifier to the router.
  1. Hold down the “Wi-Fi” Button for 3 seconds to stop the Wi-Fi function.
  2. Perform “INITIAL SET UP: 2 Connection of the air purifier and a router”. (Page 10)

When changing the smart device

• Perform the following steps.
  1. Delete the registration of the old smart device from the designated App.
  2. Use the new smart device to perform “INITIALSET UP:
  1 Download & Sign up, and
  3 Ensure connection between the air purifier and a smart device”. (Page 10,

When going to dispose or hand over the air purifier

• Perform the following steps, to prevent leak of personal information.
  1. Delete the registration of the air purifier from the designated App.
  2. Perform “A4: Initialization of Wi-Fi function”. (Page 16)

If your air purifier is handed over from a third party

• To prevent unauthorized access from a third party, perform “A4: Initialization of Wi-Fi function”.
  (Page 16)

Wi-Fi Lamp blinks slowly

• It is one of the following status.
  A. The Wi-Fi connection of the air purifier and a router is in setup.
  B. The connection of the air purifier and a smart device is in setup.
  C. The software for the Wi-Fi function in the air purifier is being updated.

Wi-Fi Lamp blinks fast

• Network error. Please confirm the Wi-Fi network status from “A7: Display Wi-Fi network status”. (Page 17)

Wi-Fi Lamp goes off

• The air purifier cannot connect to the router.
  Check the following:
  A. Is the power plug correctly connected?
  B. Has the Wi-Fi function been stopped? Confirm the Wi-Fi network status from “A7: Display Wi-Fi network status”. (Page 17)

One of “ ” to “ ” cannot be selected in the Wi-Fi setting mode. (Page 16 – 17)

• If the Wi-Fi adapter is off, one of “A2” to “A6” may not be selectable.

SPECIFICATIONS

Model|

KI-N50

|

KI-N40

---|---|---
Power Supply|

220-240 V ~ 50-60 Hz

Fan Speed Adjustment| MAX| MED| LOW| MAX| MED| LOW
CLEAN AIR| Fan Speed (m3 / hour)| 306| 168| 60| 240| 150| 60
Rated Power (W)| 51| 17| 5.5| 29| 14| 5.5
Noise Level (dBA) 1| 51| 40| 17| 46| 38| 17
CLEAN AIR & HUMIDIFY| Fan Speed (m3 / hour)| 252| 186| 66| 174| 138| 60
Rated Power (W)| 32| 22| 6.7| 17| 15| 6.5
Noise Level (dBA) 1| 47| 43| 20| 38| 35| 19
Humidification (mL / hour) *2| 600| 480| 200| 440| 370| 190
Standby Power (W)|

1.7 (When Wi-Fi adapter is ON.)
1.3 (When Wi-Fi adapter is OFF.)

Recommended Room Size (m2) 3| ~ 38| ~ 28
High Density Plasmacluster Ion Recommended Room Size (m2) 4| ~ 21| ~ 17
Humidifying Tray Capacity (L)|

Approx. 2.7

Sensors|

Sensitive Dust / Odor / Light / Temperature / Humidity

Filter Type|

HEPA*5 / Deodorizing / Humidifying

Cord Length (m)|

2.0

Dimensions (mm)|

384 (W) × 230 (D) × 619 (H)

Weight (kg)|

Approx. 8.2

1 • Noise level is measured based on the JEM1467 standard of the Japan Electrical Manufacturers’ Association.
2 • The amount of humidification changes in accordance with indoor and outdoor temperature and humidity.
The amount of humidification increases as temperatures rise or humidity decreases.
The amount of humidification decreases as temperatures decrease or humidity rises.
• Measurement Conditions: 20ºC, 30% humidity (according to JEM1426).
3 • The recommended room size is appropriate for operating the product at maximum fan speed.
• The recommended room size is an area in which a given amount of dust particles can be removed in 30 minutes (according to JEM1467).
4 • Room size in which approximately 25000 ions per cubic centimeter can be measured in the center of the room when the product is placed next to a wall, is running at MED mode settings, and is at a height of approximately 1.2 meters from the floor.
*5 • The filter removes more than 99.97% of particles at least 0.3 microns in size (according to JEM1467).

Standby Power
When the product’s power plug is inserted in a wall outlet it consumes standby power in order to operate electrical circuits.
To conserve energy, unplug the power cord when the product is not in use.

INTELLECTUAL PROPERTY RIGHTS FOR THIS PRODUCT

• Software structure
  Software installed in this product is structured with multiple independent software components, each of them has our or third-party’s copyright.

• Software of our development and free software
  Among the software components of this product, for software we developed or created and incidental documents has our copyright. And they are protected by copyright law, international regulation and other related laws.
  Also this product uses software components distributed as free software with third-party’s copyright.

• Obligation of license indication
  Some software components installed in this product are required to indicate the license by those copyright holders.
  License indications of such software components are as below:

• Expat

Copyright (c) 1998, 1999, 2000 Thai Open Source Software Center Ltd and Clark Cooper
Copyright (c) 2001, 2002, 2003, 2004, 2005, 2006 Expat maintainers.
Permission is hereby granted, free of charge, to any person obtaining a copy of this software and associated documentation files (the “Software”), to deal in the Software without restriction, including without limitation the rights to use, copy, modify, merge, publish, distribute, sublicense, and/or sell copies of the Software, and to permit persons to whom the Software is furnished to do so, subject to the following conditions:
The above copyright notice and this permission notice shall be included in all copies or substantial portions of the Software.
EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY, WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR OTHER DEALINGS IN THE SOFTWARE.

• Wslay

The MIT License
Copyright (c) 2011, 2012 Tatsuhiro Tsujikawa
Permission is hereby granted, free of charge, to any person obtaining a copy of this software and associated documentation files (the “Software”), to deal in the Software without restriction, including without limitation the rights to use, copy, modify, merge, publish, distribute, sublicense, and/or sell copies of the Software, and to permit persons to whom the Software is furnished to do so, subject to the following conditions:
The above copyright notice and this permission notice shall be included in all copies or substantial portions of the Software.
EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY, WHETHER IN AN ACTION OF CONTRACT,TORT OR OTHERWISE, ARISING FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR  OTHER DEALINGS IN THE SOFTWARE.

• libFLAC

Copyright (C) 2000-2009 Josh Coalson
Copyright (C) 2011-2014 Xiph.Org Foundation
Redistribution and use in source and binary forms, with or without modification, are permitted provided that the following conditions are met:
– Redistributions of source code must retain the above copyright notice, this list of conditions and the following disclaimer.
– Redistributions in binary form must reproduce the above copyright notice, this list of conditions and the following disclaimer in the documentation and/or other materials provided with the distribution.
– Neither the name of the Xiph.org Foundation nor the names of its contributors may be used to endorse or promote products derived from this software without specific prior written permission.
CONTRIBUTORS “AS IS” AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO, AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN POSSIBILITY OF SUCH DAMAGE.

• lw-IP

Copyright (c) 2001, 2002 Swedish Institute of Computer Science.
All rights reserved.
Redistribution and use in source and binary forms, with or without modification, are permitted provided that the following conditions are met:
1. Redistributions of source code must retain the above copyright notice, this list of conditions and the following disclaimer.
2. Redistributions in binary form must reproduce the above copyright notice, this list of conditions and the following disclaimer in the documentation and/or other materials provided with the distribution.
3. The name of the author may not be used to endorse or promote products derived from this software without specific prior written permission.
OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR
LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES(INCLUDING, BUT NOT LIMITED TO, AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN POSSIBILITY OF SUCH DAMAGE.
This file is part of the lwIP TCP/IP stack.
Author: Adam Dunkels adam@sics.se

• JSMN

Copyright (c) 2010 Serge A. Zaitsev
Permission is hereby granted, free of charge, to any person obtaining a copy of this software and associated documentation files (the “Software”), to deal in the Software without restriction, including without limitation the rights to use, copy, modify, merge, publish, distribute, sublicense, and/or sell copies of the Software, and to permit persons to whom the Software is furnished to do so, subject to the following conditions:
The above copyright notice and this permission notice shall be included in all copies or substantial portions of the Software.
EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY, WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR OTHER DEALINGS IN THE SOFTWARE.

• mbedTLS

Copyright (C) 2006-2015, ARM Limited, All Rights Reserved you may not use this file except in compliance with the License.
You may obtain a copy of the License at http://www.apache.org/licenses/LICENSE-2.0
Unless required by applicable law or agreed to in writing, software distributed under the License is distributed on an “AS IS” BASIS, WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied. See the License for the specific language governing permissions and limitations under the License.

• wps supplicant

Copyright (c) 2003-2017, Jouni Malinen j@w1.fi and contributors All Rights Reserved.
Redistribution and use in source and binary forms, with or without modification, are permitted provided that the following conditions are met:
1. Redistributions of source code must retain the above copyright notice, this list of conditions and the following disclaimer.
2. Redistributions in binary form must reproduce the above copyright notice, this list of conditions and the following disclaimer in the documentation and/or other materials provided with the distribution.
3. Neither the name(s) of the above-listed copyright holder(s) nor the names of its contributors may be used to endorse or promote products derived from this software without specific prior written permission.
CONTRIBUTORS “AS IS” AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE  CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL,   SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING  NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE.

• newLIB

(1) Red Hat Incorporated
Copyright (c) 1994-2009 Red Hat, Inc. All rights reserved.
This copyrighted material is made available to anyone wishing to use, modify, copy, or redistribute it subject to the terms and conditions of the BSD License.
This program is distributed in the hope that it will be useful, but WITHOUT ANY WARRANTY expressed or implied, including the implied warranties of MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. A copy of this license is available at http://www.opensource.org/licenses. Any Red Hat trademarks that are incorporated in the source code or documentation are not subject to the BSD License and may only be used or replicated with the express permission of Red Hat, Inc.
(2) University of California, Berkeley
Copyright (c) 1981-2000 The Regents of the University of California.
All rights reserved.
Redistribution and use in source and binary forms, with or without modification, are permitted provided that the following conditions are met:

• Redistributions of source code must retain the above copyright notice, this list of conditions and the following disclaimer.
• Redistributions in binary form must reproduce the above copyright notice, this list of conditions and the following disclaimer in the documentation and/or other materials provided with the distribution.
• Neither the name of the University nor the names of its contributors may be used to endorse or promote products derived from this software without specific prior written permission.

CONTRIBUTORS “AS IS” AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE,
(3) David M. Gay (AT&T 1991, Lucent 1998) The author of this software is David M. Gay. Copyright (c) 1991 by AT&T. Permission to use, copy, modify, and distribute this software for any purpose without fee is hereby granted, provided that this entire notice is included in all copies of any software which is or includes a copy or modification of this software and in all copies of the supporting documentation for such software.
IMPLIED WARRANTY. IN PARTICULAR, NEITHER THE AUTHOR NOR AT&T MAKES ANY REPRESENTATION OR WARRANTY OF ANY KIND CONCERNING THE MERCHANTABILITY OF THIS SOFTWARE OR ITS FITNESS FOR ANY PARTICULAR PURPOSE.
The author of this software is David M. Gay.
Copyright (C) 1998-2001 by Lucent Technologies All Rights Reserved
Permission to use, copy, modify, and distribute this software and its documentation for any purpose and without fee is hereby granted, provided that the above copyright notice appear in all copies and that both that the copyright notice and this permission notice and warranty disclaimer appear in supporting documentation, and that the name of Lucent or any of its entities not be used in advertising or publicity pertaining to distribution of the software without specific, written prior permission.
LUCENT DISCLAIMS ALL WARRANTIES WITH REGARD TO THIS SOFTWARE, INCLUDING ALL IMPLIED WARRANTIES OF MERCHANTABILITY AND LIABLE FOR ANY SPECIAL, INDIRECT OR CONSEQUENTIAL DAMAGES OR OR PROFITS, WHETHER IN AN ACTION OF CONTRACT, NEGLIGENCE OR OTHER TORTIOUS ACTION, ARISING OUT OF OR IN CONNECTION WITH THE USE OR PERFORMANCE OF THIS SOFTWARE.
(4) Advanced Micro Devices
Copyright 1989, 1990 Advanced Micro Devices, Inc.
This software is the property of Advanced Micro Devices, Inc (AMD) which specifically grants the user the right to modify, use and distribute this software provided this notice is not removed or altered. All other rights are reserved by AMD.
AMD MAKES NO WARRANTY OF ANY KIND, EXPRESS OR IMPLIED, WITH INCIDENTAL OR CONSEQUENTIAL DAMAGES IN CONNECTION WITH OR ARISING FROM THE FURNISHING, PERFORMANCE, OR USE OF THIS SOFTWARE.
So that all may benefit from your experience, please report any problems or suggestions about this software to the 29K Technical Support Center at 800-2929-AMD (800-292-9263) in the USA, or 0800-89-1131 in the UK, or 0031-11-1129
in Japan, toll free. The direct dial number is 512-462-4118.
Advanced Micro Devices, Inc.
29K Support Products
Mail Stop 573
5900 E. Ben White Blvd.
Austin, TX 78741
800-292-9263
(7) Sun Microsystems
Copyright (C) 1993 by Sun Microsystems, Inc. All rights reserved.
Developed at SunPro, a Sun Microsystems, Inc. business. Permission to use, copy, modify, and distribute this software is freely granted, provided that this notice is preserved.
(8) Hewlett Packard
(c) Copyright 1986 HEWLETT-PACKARD COMPANY
To anyone who acknowledges that this file is provided “AS IS” without any express or implied warranty:
permission to use, copy, modify, and distribute this file for any purpose is hereby granted without fee, provided that the above copyright notice and this notice appears in all copies, and that the name of Hewlett-Packard Company not be used in advertising or publicity pertaining to distribution of the software without specific, written prior permission. Hewlett-Packard Company makes no representations about the suitability of this software for any purpose.
(9) Hans-Peter Nilsson
Copyright (C) 2001 Hans-Peter Nilsson Permission to use, copy, modify, and distribute this software is freely granted, provided that the above copyright notice, this notice and the following disclaimer are preserved with no changes.
IMPLIED WARRANTIES, INCLUDING, WITHOUT LIMITATION, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE.
(11) Christopher G. Demetriou
Copyright (c) 2001 Christopher G. Demetriou All rights reserved.
Redistribution and use in source and binary forms, with or without modification, are permitted provided that the following conditions are met:

1. Redistributions of source code must retain the above copyright notice, this list of conditions and the following disclaimer.
2. Redistributions in binary form must reproduce the above copyright notice, this list of conditions and the following disclaimer in the documentation and/or other materials provided with the distribution.
3. The name of the author may not be used to endorse or promote products derived from this software without specific prior written permission.

OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR  CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO, AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN POSSIBILITY OF SUCH DAMAGE.
(12) SuperH, Inc.
Copyright 2002 SuperH, Inc. All rights reserved
This software is the property of SuperH, Inc (SuperH) which specifically grants the user the right to modify, use and distribute this software provided this notice is not removed or altered. All other rights are reserved by SuperH.
SUPERH MAKES NO WARRANTY OF ANY KIND, EXPRESS OR IMPLIED, LIABLE FOR INDIRECT, SPECIAL, INCIDENTAL OR CONSEQUENTIAL DAMAGES IN CONNECTION WITH OR ARISING FROM THE FURNISHING, PERFORMANCE, OR USE OF THIS SOFTWARE. So that all may benefit from your experience, please report any problems or  suggestions about this software to the SuperH Support Center via e-mail at softwaresupport@superh.com .
SuperH, Inc.
405 River Oaks Parkway
San Jose
CA 95134
USA
(13) Royal Institute of Technology
Copyright (c) 1999 Kungliga Tekniska Högskolan
(Royal Institute of Technology, Stockholm, Sweden).
All rights reserved.
Redistribution and use in source and binary forms, with or without modification, are permitted provided that the following conditions are met:

1. Redistributions of source code must retain the above copyright notice, this list of conditions and the following disclaimer.
2. Redistributions in binary form must reproduce the above copyright notice, this list of conditions and the following disclaimer in the documentation and/or other materials provided with the distribution.
3. Neither the name of KTH nor the names of its contributors may be used toendorse or promote products derived from this software without specific prior written permission.

THIS SOFTWARE IS PROVIDED BY KTH AND ITS CONTRIBUTORS “AS IS” AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL KTH OR ITS CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
(14) Alexey Zelkin
Copyright (c) 2000, 2001 Alexey Zelkin phantom@FreeBSD.org All rights reserved.
Redistribution and use in source and binary forms, with or without modification, are permitted provided that the following conditions are met:

1. Redistributions of source code must retain the above copyright notice, this list of conditions and the following disclaimer.
2. Redistributions in binary form must reproduce the above copyright notice, this list of conditions and the following disclaimer in the documentation and/or other materials provided with the distribution.

THIS SOFTWARE IS PROVIDED BY THE AUTHOR AND CONTRIBUTORS “AS IS” AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE AUTHOR OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
(16) FreeBSD
Copyright (c) 1997-2002 FreeBSD Project.
All rights reserved.
Redistribution and use in source and binary forms, with or without modification, are permitted provided that the following conditions are met:

1. Redistributions of source code must retain the above copyright notice, this list of conditions and the following disclaimer.
2. Redistributions in binary form must reproduce the above copyright notice, this list of conditions and the following disclaimer in the documentation and/or other materials provided with the distribution.

THIS SOFTWARE IS PROVIDED BY THE AUTHOR AND CONTRIBUTORS AS IS” AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND SHALL THE AUTHOR OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS: OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
(17) S. L. Moshier
Author: S. L. Moshier.
Copyright (c) 1984,2000 S.L. Moshier
Permission to use, copy, modify, and distribute this software for any purpose without fee is hereby granted, provided that this entire notice is included in all copies of any software which is or includes a copy or modification of this software and in all copies of the supporting documentation for such software.
THIS SOFTWARE IS BEING PROVIDED “AS IS”, WITHOUT ANY EXPRESS OR IMPLIED WARRANTY. IN PARTICULAR, THE AUTHOR MAKES NO REPRESENTATION OR WARRANTY OF ANY KIND CONCERNING THE MERCHANTABILITY OF THIS SOFTWARE OR ITS FITNESS FOR ANY PARTICULAR PURPOSE.
(18) Citrus Project
Copyright (c)1999 Citrus Project, All rights reserved.
Redistribution and use in source and binary forms, with or without modification, are permitted provided that the following conditions are met:

1. Redistributions of source code must retain the above copyright notice, this list of conditions and the following disclaimer.
2. Redistributions in binary form must reproduce the above copyright notice, this list of conditions and the following disclaimer in the documentation and/or other materials provided with the distribution.

THIS SOFTWARE IS PROVIDED BY THE AUTHOR AND CONTRIBUTORS‘AS IS” AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A  PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE AUTHOR OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS: OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY,  OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
(19) Todd C. Miller
Copyright (c) 1998 Todd C. Miller Todd.Miller@courtesan.com All rights reserved.
Redistribution and use in source and binary forms, with or without modification, are permitted provided that the following conditions are met:

1. Redistributions of source code must retain the above copyright notice, this list of conditions and the following disclaimer.
2. Redistributions in binary form must reproduce the above copyright notice, this list of conditions and the following disclaimer in the documentation and/or other materials provided with the distribution.
3. The name of the author may not be used to endorse or promote products derived from this software without specific prior written permission.

THIS SOFTWARE IS PROVIDED “AS IS” AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE AUTHOR BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
(26) Mike Barcroft
Copyright (c) 2001 Mike Barcroft mike@FreeBSD.org All rights reserved.
Redistribution and use in source and binary forms, with or without modification, are permitted provided that the following conditions are met:

1.  Redistributions of source code must retain the above copyright notice, this list of conditions and the following disclaimer.
2. Redistributions in binary form must reproduce the above copyright notice, this list of conditions and the following disclaimer in the documentation and/or other materials provided with the distribution.

THIS SOFTWARE IS PROVIDED BY THE AUTHOR AND CONTRIBUTORS ‘AS IS” AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE AUTHOR OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS: OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
(35) – ARM Ltd (arm and thumb variant targets onty)
Copyright (c) 2009 ARM Ltd All rights reserved.
Redistribution and use in source and binary forms, with or without modification, are permitted provided that the following conditions are met:

1. Redistributions of source code must retain the above copyright notice, this list of conditions and the following disclaimer.
2. Redistributions in binary form must reproduce the above copyright notice, this list of conditions and the following disclaimer in the documentation and/or other materials provided with the distribution.
3. The name of the company may not be used to endorse or promote products derived from this software without specific prior written permission.

THIS SOFTWARE IS PROVIDED BY ARM LTD ‘AS IS” AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL ARM LTD BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
(41) Ed Schouten – Free BSD
Copyright (c) 2008 Ed Schouten ed@FreeBSD.org All rights reserved.
Redistribution and use in source and binary forms, with or without modification, are permitted provided that the following conditions are met:

1. Redistributions of source code must retain the above copyright notice, this list of conditions and the following disclaimer.
2. Redistributions in binary form must reproduce the above copyright notice, this list of conditions and the following disclaimer in the documentation and/or other materials provided with the distribution.

THIS SOFTWARE IS PROVIDED BY THE AUTHOR AND CONTRIBUTORS “AS IS” AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A  PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE AUTHOR OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT  LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS, OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY,  OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.

• elibgloss

(1) Red Hat Incorporated
Copyright (c) 1994-2009 Red Hat, Inc. All rights reserved.
This copyrighted material is made available to anyone wishing to use, modify, copy, or redistribute it subject to the terms and conditions of the BSD License. This program is distributed in the hope that it will be useful, but WITHOUT ANY WARRANTY expressed or implied, including the implied warranties of MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. A copy of this license is available at http://www.opensource.org/licenses. Any Red Hat trademarks that are incorporated in the source code or documentation are not subject to the BSD License and may only be used or replicated with the express permission of Red Hat, Inc.
(2) University of California, Berkeley
Copyright (c) 1981-2000 The Regents of the University of California.
All rights reserved.
Redistribution and use in source and binary forms, with or without modification, are permitted provided that the following conditions are met:

• Redistributions of source code must retain the above copyright notice, this list of conditions and the following disclaimer.
• Redistributions in binary form must reproduce the above copyright notice, this list of conditions and the following disclaimer in the documentation and/or other materials provided with the distribution.
• Neither the name of the University nor the names of its contributors may be used to endorse or promote products derived from this software without specific prior written permission.

THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS “AS IS* AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND  FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT OWNER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
(3) DJ Delorie
Copyright (C) 1993 DJ Delorie
All rights reserved.
Redistribution, modification, and use in source and binary forms is permitted Provided that the above copyright notice and following paragraph are duplicated in all such forms.
This file is distributed WITHOUT ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.
(4) (formerty GPL for fr30)
The GPL is no longer applicable to the fr30 platform. The piece of code (syscalls.c) referencing the GPL has been officially relicensed.
(5) Advanced Micro Devices
Copyright 1989, 1990 Advanced Micro Devices, Inc.
This software is the property of Advanced Micro Devices, Inc (AMD) which specifically grants the user the right to modify, use and distribute this software provided this notice is not removed or altered. All other rights are reserved by AMD.
AMD MAKES NO WARRANTY OF ANY KIND, EXPRESS OR IMPLIED, WITH REGARD TO THIS SOFTWARE. IN NO EVENT SHALL AMD BE LIABLE FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES IN CONNECTION WITH OR ARISING FROM THE FURNISHING, PERFORMANCE, OR USE OF THIS SOFTWARE.
So that all may benefit from your experience, please report any problems or suggestions about this software to the 29K Technical Support Center at 800-29-29-AMD (800-292-9263) in the USA, or 0800-89-1131 in the UK, of 0031-11-1129 in Japan, toll free. The direct dial number is 512-462-4118.
Advanced Micro Devices, Inc.
29K Support Products
Mail Stop 573
5900 E. Ben White Biv.
Austin, TX 78741
800-292-9263
(8) Sun Microsystems
Copyright (C) 1993 by Sun Microsystems, Inc. All rights reserved.
Developed at SunPro, a Sun Microsystems, Inc. business.
Permission to use, copy, modify, and distribute this software is freety granted, provided that this notice is preserved.
(9) Hewlett Packard
(c) Copyright 1986 HEWLETT-PACKARD COMPANY
To anyone who acknowledges that this file is provided “AS IS” without any express or implied warranty:
permission to use, copy, modify, and distribute this file for any purpose is hereby granted without fee, provided that the above copyright notice and this notice appears in all copies, and that the name of Hewlett-Packard Company not be used in advertising or publicity pertaining to distribution of the software without specific, written prior permission. Hewlett-Packard Company makes no representations about the suitability of this software for any purpose.
(10) Hans-Peter Nilsson
Copyright (C) 2001 Hans-Peter Nilsson
Permission to use, copy, modify, and distribute this software is freety granted, provided that the above copyright notice, this notice and the following disclaimer are preserved with no changes.
THIS SOFTWARE IS PROVIDED “AS IS” AND WITHOUT ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, WITHOUT LIMITATION, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE.
(14) – National Semiconductor Corporation
Copyright (c) 2004 National Semiconductor Corporation
The authors hereby grant permission to use, copy, modify, distribute, and license this software and its documentation for any purpose, provided that existing copyright notices are retained in all copies and that this notice is included verbatim in any distributions. No written agreement, license, or royalty fee is fequired for any of the authorized uses.
Modifications to this software may be copyrighted by their authors and need not follow the licensing terms described here, provided that the new terms are clearly indicated on the first page of each file where they apply.

SHARP CORPORATION
OSAKA, JAPAN
Production control code TINS-B451KKRZ 22G 1

Documents / Resources

| SHARP KI-N50 Air Purifier Humidifying Function [pdf] Instruction Manual
KI-N50 Air Purifier Humidifying Function, KI-N50, Air Purifier Humidifying Function, Purifier Humidifying Function, Humidifying Function, Function
---|---

References

• Apache License, Version 2.0
• Licenses – Open Source Initiative
• Manual-Hub.com – Free PDF manuals!

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>