Guangdong Xizhongxi Technology G03 TWS Bluetooth Earbuds User Manual
- June 4, 2024
- Guangdong Xizhongxi Technology
Table of Contents
Guangdong Xizhongxi Technology G03 TWS Bluetooth Earbuds
Thanks for using our wireless electronic products. To make good and full use
of our products, please read the manual carefully before using . Notice: To
avoid unnecessary troubles, please do NOT disassemble these products by
yourself and please
use the standard charger to charge.Make sure that the ear e caps face down and
put the earbuds into your ears in the angle shown as the picture on the
right.
After putting on the earbuds, please gently rotate the earbuds to a comfortable and secure position shown as picture 3 on the right. Now the earbuds are put on correctly!
Error
Do not put on the earbuds like the way shown as the picture on the right 3.0pen the case, the earbuds wll tum on automatically 1 breathing, vand hile be the ready other for one’s pairing indicator (one 1 earOud’s slow flashing indicator ) .
- The earbuds will automatically turn on after opening the top lid of the charging case.
- Press the power switch and hold for 5s, and then the earbuds will turn on (when they are off and not in the case) .
- Put the earbuds into tlle charging case and close the lid, they will automatically shut down.
- While in the non-wor king state, press and hold the power switch for 5s, the two earbuds will turn off at the same time.
- It will automatically shut dawn after no connection far mare than 5 minutes
Default to Music mode when turn on
Notes
charging case is out of power, it may cause the earbuds fairemain connected
tto l the to shut phone down even and when they are placed in he charging
case. So please remember to charge the charging case in time.
If moisture remains in the audio output hole, the sound may become fuzzy or completelyIn inaudible. This is quite a normal case. this case, audio output please hole remove down the seveear caps and shake theral times lo allow water to flow out or let it air dry for 1-2 hours, and then the sound quality will become normal.
The is not Charging waterproof cable iThe s Cnot harging waterproof case Do disinot niec1 use the hot pmduct water lo If there is et on the back surface, into the please charg\Vipe ing it with case
- If or the product is dirty, please do not rinse directly with endedwate or use boil:ng water to soak and disinfect it.
- It is recommended to wipe the earbuds with an alcohol cloth or a wet 1issue.
- lufp t hine tpimroed uacritd f alellts into the water accidentally, please pick it for two hours befoirte d urys ibnyg nita t(uortahle wr.vinisde u i,1t dweilr tahffee sctu nthseh ine sound qualiiy, thus fail to give you a better using experience
Product Overview
- Tear off the insulating film.
- Put the earbuds into the charging case and close it to charge (then the case start charging).
- Turn on Bluetoolh function on your phone and search for [G03 ] and connect it.
Warearl:luds m not notice: syncL hronWhen izede, ither please eartum bud off no Bluetooth sound on or twothe press phone the and then power turn switch off t11e and earbudshold . for 5s After.vato trudsr, n on please the earbuds ngand , whikeep
- Wquickly hen click the both earbuds power are swon itch and four not times conne(the cted, connection will be oth cleaned indicators as indicflash ator tw1 ice, flashesand the three earbuds times and off)
- phone Please and delete search all conagain nectifor “G03” in Bluetooth on the phone and reconnect.
Wireless charging is available
Steps of charging for earbuds:
Put the earbuds in the charging case, and close the case to charge them, and they will automatically turn off and disconnect when the charging case lid is closed.
Charging case
Please use a charger with an output voltage of DCSV/1A to charge the case. You
can also use a computer USB or other USB interface charger to charge (please
DO remember to choose a charger certified by regular manufacturers
lf there is noise, broken sound, or low sound, please take off the silicone ear.
cap and wipe it with a cotton swab. lf the earbud is not charged properly, please wipe the charging column with a cotton swab, and then try again.
- Do not use corrosive liquid to clean this product.
- lf it is stainad with any chernicals, please rub it with a wet cloth wet with clean water.
- Do not use this product under extreme circumstances ror lemperalure belo\V -1 D degree Celsius or above 60 degree Celsius .
- To avoid explosion, please do nol lhro\v ltiis product into fire.
- To avoid scratches; please do not let the earbuds expose lo sharp objects.
- Do not insert objects into the earbuds, otherwise it would cause dc:nnage to the internal components.
- Do not disassemble the product.
- tIno othrdee er taor bkueedps tahnedir ldiioe tinmoet , leplaevaese t hkeeemp eremgpiJtlayr bcahtatregrey ,
- Please do not charge products with power adapter over 2A current. Excessivs current may cause damage to battery
FCC Caution
This device complies with part 15 of the FCC Rules. Operation is subject to
the following two conditions: This device may not cause harmful interference,
and this device must accept any interference received, including interference
that may cause undesired operation. Any Changes or modifications not expressly
approved by the party responsible for compliance could void the user’s
authority to operate the equipment.
Note:
This equipment has been tested and found to comply with the limits for a Class
B digital device, pursuant to part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates uses and can radiate radio
frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and
on, the user is encouraged to try to correct the interference by one or more
of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
The device has been evaluated to meet general RF exposure requirement. The device can be used in portable exposure condition without restriction.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>