EARTHQUAKE SOUND SM6BT Professional Studio Monitor User Manual

**EARTHQUAKE SOUND SM6BT Professional Studio Monitor User Manual

**

Safety Instructions

Safety First

This documentation contains general safety, installation, and operating instructions for the SM6BT studio monitors. It is important to read this user’s manual before attempting to use this product. Pay particular attention to the safety instructions.

Symbols Explained:

Appears on the component to indicate the presence of uninsulated, dangerous voltage inside the enclosure – voltage that may be sufficient to constitute a risk of shock.

CAUTION
Calls attention to a procedure, practice, condition or the like that, if not correctly performed or adhered to, could result in injury or death.

WARNING
Calls attention to a procedure, practice, condition or the like that, if not correctly performed or adhered to, could result in damage to or destruction of part or all of the product.

This calls attention to any information that is essential  to highlight.

This triangle, which appears on your component, alerts you to the presence of uninsulated, dangerous voltage inside the enclosure – voltage that may be sufficient to constitute a risk of shock.

This triangle, which appears on your component, alerts you to important operating and maintenance instructions in this accompanying litera.

Safety Instructions (continued) Warranty Information

1.  Read these instructions in their entirety.
2.  Store this manual and packaging in a safe place.
3. Read all warnings.
4. Follow instructions (do not take shortcuts).
5.  Do not use this apparatus near water.
6. Clean only with a dry cloth.
7. Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions.
8. Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatuses that produce heat.
9. Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has two blades with one wider than the other. The grounding-type plug has two blades and a third grounding prong. The wide blade or the third prong is provided for your safety. If the provided plug does not fit into your outlet, consult an electrician for replacement of the obsolete outlet. 10. Protect the power cord from being walked on or pinched, particularly at plugs, convenience receptacles, and the point where they exit from the apparatus.
10. Only use attachments and accessories specified by the manufacturer.
11. Use only a compatible rack or cart for the final resting position.
12. Unplug this apparatus during lightning storm or when unused for a long period of time.
13. Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been damaged in a way such as: powersupply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped.
14. To reduce the risk of fire or electric shock, do not expose this apparatus to rain or moisture.

Notes

Pin 1 Sleeve (Shield) = Ground (cable shield)

Pin 2 Tip = Positive/Red/Ho
Pin 3 Ring = Negative/Black/Cold

Introduction

Thank you for purchasing the Earthquake Sound SM6BT professional active studio monitor. Regarding studio monitors, one would desire accurate audio reproduction, sound clarity, transparent performance with low distortion, and exceptional imaging. With those characteristics in mind, every Earthquake SM6BT studio monitor component has been carefully selected to deliver on those characteristics demanded by audiophiles and professionals worldwide.

Equipped with a bi-amplified class AB amplifier, the SM6BT studio monitor accepts unbalanced (RCA) and balanced (XLR/TRS combo jack) inputs as well as Bluetooth® v5.3 True Wireless Stereo (TWS) connectivity for general everyday audio enjoyment. If extra bass is needed, a subwoofer output is available to connect a powered subwoofer for a complete 2.1 audio system. The SM6BT also features a high frequency trim adjustment control to tailor the sound to your listening preferences.

The drivers installed in each SM6BT monitor feature a stiff and low-mass 6-inch carbon fiber cone woofer for extremely low harmonic distortion and a 2-inch wide band ribbon tweeter for ultra-clear, detailed, and dynamic treble output. Integrating these components ensures balance, transparency, and neutral audio reproduction. Discover details in music and movies that you never thought were possible with the SM6BT.

**Amplifier Features

**

1. Unbalanced RCA Input
   RCA input for connecting the SM6BT monitor to your TV, computer, DJ equipment, mobile device, etc.
   2b Balanced 1/4-Inch TRS Input
   10kOhm balanced TRS input for connecting the SM6BT monitor to your audio interface or mixer. For best result, be sure to use a balanced 1/4-inch TRS phone plug.
   2a. Balanced XLR Input
   10kOhm balanced XLR input for connecting the SM6BT monitor to your audio interface or mixer.

NOTE:

Pin 1: Sleeve (Shield) = Ground (cable shield)
Pin 2: Tip = Positive/Red/Hot
Pin 3: Ring = Negative/Black/Cold

CONNECT ONLY ONE INPUT SOURCE AT A TIME.

Troubleshooting The SM6BT Monitor

The Front LED Does Not Light Up

• Inspect the power cable. Never use one that has been altered in any way.
• Verify the AC power outlet is active and supplying the appropriate AC voltage.
• Verify the monitor’s AC selector is set to the proper setting with the correct fuse installed (refer to page 7 for fuse rating and how to access the fuse compartment). Make sure that the fuse is not blown.
• Verify that the power cord is securely plugged into the unit and the power AC outlet.
• Check that the monitor’s POWER switch is ON.
• Check to ensure the LED ON/OFF selector is in the correct position.
• If the fuse(s) blow once the monitor is switched on, please contact Earthquake Sound Technical Support at (1-510-732-1000 or tech@earthquakesound.com)..)

The Front LED Lights Up But There Is No Sound

• Perform the troubleshooting steps above before proceeding with the next steps.
• Verify that all devices plugged into the same AC outlet are still working.
• Make sure that the signal source (e.g., mixing console, DJ workstation, etc.) is at a level that can properly send a signal to the monitor(s).
• Make sure the VOLUME knob (system gain potentiometer) is turned fully clockwise to +6dB.
• Ensure the audio source cable is firmly plugged into both the source output and the monitor input.
• If operating two monitors and this problem only occurs on one of the units, exchange the audio input cable from the non-working unit to the working one to determine where the problem lies (the monitor, the cable, or elsewhere).
• If the problem persists, please contact Earthquake Sound technical service. The Monitor Suddenly Stops Working

Turn the SM6BT monitor off.

• Perform the troubleshooting steps above before proceeding with the next steps.
• Carefully check if the amplifier’s back plate is hot. It is possible that the protection circuitry was triggered and shut down because it ran at its highest power output for an extended time. Turn the monitor power off and keep it off for at least 30 minutes to allow the amplifier to cool down before turning it back on.
• Increase the volume to check for normal operation.

Main Power Switch
This switch controls the AC power going to the SM6BT monitor. We suggest keeping the switch in the OFF position when the monitor is not being used for an extended period of time.
**

110V/220V Selector Switch
The SM6BT monitors can operate in a 110-120V or 220- 240V environment. Simply slide the selector to the required power input setting and replace the fuse to the proper rating prior to connecting the monitors to a power source.
USE OF IMPROPER VOLTAGE MAY RESULT IN HAZARDOUS CONDITIONS AND/OR DAMAGE TO THE
MONITOR COMPONENTS THAT ARE NOT COVERED BY THE FACTORY WARRANTY. FOR YOUR SAFETY, PLEASE MAKE SURE THAT THE MONITOR IS NOT CONNECTED TO ANY POWER SOURCE PRIOR TO ACCESSING THE AC SELECTOR AND FUSE COMPARTMENT.
AC Power Inlet with Fuse Holder
This AC line connector is fused to protect the amplifier from unwanted power surges. Be sure to use the proper fuse rating when replacing the existing fuse: ø5 x 20mm 2A/250V UL/VDE slow blow tube fuse To access the fuse compartment, simply unplug the power cable from the monitor, place a flat-head screw driver in the small notch and pry it open as illustrated
Subwoofer Output**
This unbalanced RCA output is used for providing signal to a powered subwoofer if needed.

ON=L CH
OFF=R CH
TWS Status LED Indicator
This LED is the True Wireless Stereo (TWS) master speaker and slave speaker indicator. When TWS pairing succeeds, the software automatically assigns the master and slave speakers. Usually, the master speaker is the left channel, and the slave speaker is the right channel.

True Wireless Stereo (TWS)
This button is used to put the two SM6BT monitors in True Wireless Stereo pairing mode. See page #11 for TWS pairing procedure.

Input Selector Switch
This is a 2-way selector switch that allows you to select between input methods. Sliding the switch up enables Bluetooth® and sliding it down enables the unbalanced or balanced inputs. When using the Bluetooth® input, make sure that this switch is set to the correct position before pairing to any Bluetooth® enabled devices.

LED ON/OFF Selector Switch
This is a 2-way selector switch allows for the user to turn the front mounted LED indicator light on or off.

Level Adjustment Knob
This level knob controls the monitor’s input sensitivity. Typically, you would want to set the knob to the maximum setting (+6dB), adjust the source’s output level and then use the level knob to match the left and right monitors.

HF Trim Knob
This high frequency adjustment knob is factory set at 0dB or flat. Simply adjust this knob accordingly to tailor the sound to your listening preferences.

SM6BT Specifications

RCA Sub Out Bluetooth� 5.3
Controls| System Level Control (-80dB to +6dB) HF Level Adjustment (-2dB, 1dB, 0, +1dB)
Cabinet Material| 3/4″ (20mm) MDF
Cabinet Finish| Matte Black Finish
Dimensions H x W x D)| 12.75″ x 9″ x 11.5″ 324mm x 228mm x 292mm
Fuse Rating| ø5x20mm 2A/250V UL/VDE slow blow tube

SM6BT Monitor Placement

Proper placement of your SM6BT monitors is a crucial step in making sure that they perform at their best.
Studio/Stereo Application
Earthquake suggests placing the monitors within the front 1/3 of the room, about 3 to 5 feet away from each other and directed at a 60 degree angle towards your listening position.

SM6BT Monitor Surround Sound Application

Begin by placing the center channel monitor right before your listening position. Then place the front left and right monitors at an equal distance and about 25 to 30-degree angle from the center. The three front monitors (left, center, and right) should form a slight arc, as shown below. Continue placing the rear monitors at an equal distance from the listening position and angled about 90 to 110 degrees from the center, as illustrated below.

Warranty Information

5 YEAR LIMITED WARRANTY INFORMATION
Earthquake Sound warrants the original purchaser that all Factory Sealed New Audio products be free from defects in material and workmanship, under normal and proper use, for a period of five (5) year from the date of purchase (as shown on the original sales receipt with serial number affixed/written on it). The one (1) year warranty period is valid only if the product is properly installed by an Earthquake Sound authorized party and the warranty registration card is properly filled out and sent to Earthquake Sound Corporation.
If the product is installed by a non-authorized party, a thirty (30) day warranty period applies.

(A) Five (5) year limited warranty guideline

•  First Year: Earthquake pays for labor, parts and ground freight (US Mainland only, not including Alaska and Hawaii.) Shipping to us is not covered.
• Second, Third, Fourth, & Fifth Year: Earthquake pays labor only. Customer must pay for parts and freight both ways.

(B) Warning:

• Products (sent for repair) that are tested by Earthquake technicians and deemed to have no problem(s) will not be covered y the limited warranty. Customer will be charged a minimum of one (1) hour of labor (at ongoing rate) plus the shipping charges back to the customer.
• Each product sent in for repair must be packaged in its original packaging. Otherwise, repackaging charges will apply in addition to the labor, parts, and shipping charges.

(C) Earthquake agrees to repair or replace – at our discretion – all such defective products/parts subject to the following provisions:

• Defective products/parts have not been altered or repaired by other than an Earthquake factory approved technician.
• Products/parts are not subjected to negligence, misuse, accident, or  damaged by improper line voltage.
• Products/parts were used with incompatible products.
• The serial number or any part of the product has been altered, defaced, or removed.
• Products/parts have been used in any way that is contrary to Earthquake’s written instructions.

(D) Warranty Limitations:
Earthquake warranty does not cover products that have been modified or abused, including but not limited to the following:

• Damage due to misuse, abuse, or improper cleaning materials/methods.
• Bent speaker frame, broken connectors, hole(s) in speaker cone, hole(s)

Warranty Information Cont.

• in surround or dist cap, and burnt speaker voice coil.
• Fading and/or deterioration of speaker components & finish due to improper exposure to elements.
• Burnt tracers found on the printed circuit boards (PCB).
• Product/part damaged due to poor packaging or abusive shipping conditions.
• Subsequent damage to other products.

A warranty claim will not be valid if the warranty registration card is not properly filled & returned to Earthquake with a copy of the sales invoice.

(E) Service Request:
To receive product(s) service, contact Earthquake Sound’s service department at 510-732-1000 or tech@earthquakesound.com and request an RMA (Return Material Authorization) number as item(s) shipped without a valid RMA number will be refused. Make sure you provide us with your complete and correct shipping address, a valid daytime phone number, and a brief description of the problem you are experiencing with the product. In most cases, our technicians might be able to resolve the problem over the phone or via e-mail, thus eliminating the need to ship the product.

(F) Shipping Instructions:
Product(s) must be packaged inside its original protective box(es) to minimize transportation damage. Shipper claims regarding items damaged in transit must be presented to carrier. Earthquake Sound Corporation reserves the right to refuse improperly packaged product(s). A copy of the original sales receipt must accompany the product(s) returned for service. Ship the product(s) to:

Earthquake Sound Corporation. 2727 McCone Avenue. Hayward, CA 94545 The customer is responsible for the cost of shipping the product(s) to Earthquake Sound Corporation

(G) Disputes Resolution:
All disputes – between clients and Earthquake Sound Corporation – resulting from the one (1) year limited warranty policy must be resolved according to the laws & regulations of the county of Alameda, California.

References

• Sound.com
• Home - Earthquake Sound Corp.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>