LABFENG 50A-600A 110V Permanent Jewelry Welder kit User Guide

User Guide

50A-600A 110V Permanent Jewelry Welder kit

Attention, please! Improper operation may cause damage to the machine. Please read the precautions carefully

• Do not use cable to drag equipment. Cables should be away from heat, oil and other sharp objects, so as not to damage the cable.
• The equipment will automatically tune to Ortho working pattern without any action of machine in 5 minutes of power on. For avoid damage to the welding object with wrong operating.
• The tungsten electrode should keep sharp status, angle LE 25° . After use for a period, you need polishing until the tungsten electrode can not meet use length, please change in time.
• The two electrodes can never be short-circuit

1. Confirming the panel working pattem according to welding material, this equipment have set up 5 working pattern which almost meet operating demand. If you need change pattem, adjusting the 5 buttons on the panel to achieve the working condition you needed. Welding power and welding time nixie tube will indicate corespondent values.

2. If the 5 working pattern can not satisfied your need, you can adjust the quantity of welding power and the length of welding time so as to change the welding performance parameter.

3. Adjusting power, pushing the button ▼ means decrease and ▲ means increase. Adjust value of 1 to 10 integer and display of value X 10 means the percentage of actual power. Adjusting time, pushing the button ▼ means decrease and ▲ means increase. And the value according to the multiple of 3, the units is second.

4. Setting the deflate time according the proficiency of worker, which means the time of workpiece touching tungsten electrode . Pushing the select button, you can choose 0.5,1,1.5 second as deflate time.

5. The Installation of Welding Handle and Tungsten ElectrodeThe order of installation is as shown.Unplug welding handle cover in real practice and unscrew locking head, inserting tungsten electrode. Using the cover measure the tungsten electrode exposes 10-15mm after installation. Than screw locking head and cover.

6. Setting of Instruments
   Turn on the power switch, make sure the gas supply pressure of argon is 0.1Mpa.
   Attention: Argon cylinders are handled by the user

7. Welding Put welding circuit clamp clip in workpiece and grasp the welding workpiece, looking into the eyepiece and let welding place touch tungsten electrode tip. Don push too hard for left space of automatic retraction, and the machine will welding naturally.

8. Operation Tips
   Pressure Hint: The indicator light below the Select button of panel will flash, when the gas pressure of argon can not reach the welding pressure demand.(According to current setting)
   Waiting for welding: The button of wait is on means charging and the light turn to Ready means charge complete
   Ready: Everything is right after boot and the Ready indicator lit, you can start welding.

9. Operation Panel and Button Manual
   

Main Performance Parameters

In order to avoid electric shock, fire and dangerous accident when using electrical equipment, be sure to pay attention to following basic safety measures.

1. Before using the instrument, please read this manual and precautions. Placing this manual near the instrument for convenient view.
2. Please keep the electrical equipment away from children and absolutely forbid children to play this electrical equipment, spare parts and other cables.
3. The operating of the equipment should maintain good ventilation and lighting, do not work in a humid and dusty environment thus to avoid accidents by abnormal environment.
4. Never let any liquid enter the instrument.
5. There will be a strong arc light when operating, irrelevant personnel should away from the work site for avoiding damage the eyes.
6. You must completely cut off the power before clean the equipment and open the case.
7. This machine with compact and reasonable structure does not need special and tedious maintenance. Paying attention to the cleaning of the instrument. Not clean the attachments will seriously affect the observation of objects.
8. The instrument should be covered with a dust cover in non-working status.
9. For your security, please use the correct fittings.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>