New Holland LM1330-1333 Electric Wiring Diagrams User Manual

June 16, 2024
New Holland

 LM1330-1333 Electric Wiring Diagrams

New Holland LM1330-1333 Electric Wiring Diagrams SECTION 55 — ELECTRICAL CIRCUITS
Chapter 2 – Circuit diagrams

LIST OF CONNECTORS

CON.

|

DESIGNATION

---|---
X1| Connector 3 ways, rh stabiliser sensor
X10| Connector 2 ways, back up alarm
X100| Connector 4 ways, inside air sensor
X102| Connector 2 ways, engine recycling
X106| Connector 4 ways, electric fan
X11| Connector 4 ways, boom work light
X12| Connector 3 ways, low boom sensor
X129| Connector 8 ways, dashboard line conditioner line
X131| Connector 4 ways, inside heating
X132.1| Connector 1 way, inside heating
X132.2| Connector 1 way, inside heating
X132.3| Connector 1 way, heating
X132.4| Connector 1 way, heating
X137| Connector 17 ways, work selection controller
X138| Connector 2 ways, filter thermistor
X139| Connector 2 ways, filter pre heating
X14| Connector 3 ways, boom retracted sensor
X16| Connector 6 ways, engine dashboard
X17| Connector 6 ways, lh front light
X18| Connector 6 ways, rh front light
X1A2| Connector 2 ways, steering sol. valve A2
X1B2| Connector 2 ways, steering sol. valve B2
X301| Connector 2 ways, lh stabiliser lowering sol. valve
X302| Connector 2 ways, lh stabiliser lifting sol val.
X303| Connector 2 ways, rh stab. lowering sol.val.
X304| Connector 2 ways, rh stab. lift sol. valve
X305| Connector 2 ways, lh levelling sol. valve
X306| Connector 2 ways, rh levelling sol. valve
X309| Connector 2 ways, optional sol. valve
X21| Connector 12 ways, rear line dashboard
X2| Connector 3 ways, rh stabiliser sensor
X310| Connector 2 ways, tachometer sensor
X311| Connector 2 ways, pilot contr. sol. valve
X307| Connector 2 ways, telescopic extr. sol. valve
X308| Connector 4 ways, pilot contr. sol. valve
X213| Connector 2 ways, reverse sol. valve
X214| Connector 2 ways, forward speed sol. valve
X215| Connector 2 ways, gearshift selection sol. valve
X216| Connector 2 ways, 1st gear sol. valve
X217| Connector 2 ways, 2nd gear sol. valve
X218| Connector 2 ways, attachments sol. valve
X25| Connector 21 ways, dashboard line engine line
X27| Connector 9 ways, dashboard line cab line
X28a| Connector 2 ways, axle locking sol. valve
X28b| Connector 2 ways, axle locking sol. valve
X29| Connector 2 ways, cold starting sol. valve
X30| Connector 6 ways, pre heating arrangement
CON.| DESIGNATION
---|---
X4| Connector 2 ways, stop lights micro
X31| Connector 17 ways, dashboard line cab line
X32| Connector 1 way, rh front work light
X33| Connector 1 way, lh front work light
X313| Connector 2 ways, opt. sol. valve out
X37| Connector 8 ways, momentum device
X39| Connector 4 ways, rear wiper
X40| Connector 3 ways, ceiling light
X42| Connector 4 ways, parking brake switch
X43| Connector 9 ways, conditioner arrang. line
X68| Connector 1 way, rh rear work light
X48| Connector 8 ways, pilot valve
X5| Connector 2 ways, fuel level
X53| Connector 2 ways, cigarette lighter
X55| Connector 8 ways, radio brown
X56| Connector 8 ways, radio black
X6| Connector 15 ways, dashboard line rear line
X60| Connector 20 ways, instrument
X62| Connector 12 ways, gearshift control
X63| Connector 12 ways, light switch
X65| Connector 4 ways, stop micro
X67| Connector 4 ways, front wiper
X69| Connector 3 ways, load momentum
X7| Connector 18 ways, dashb. line front line
X70| Connector 10 ways, cold starting controller
X8| Connector 3 ways, rear axle sensor
X9| Connector 2 ways, load cell
X91| Connector 2 ways, conditioner press. switch
X92a| Connector 2 ways, electric fan
X92b| Connector 2 ways, electric fan
X94| Connector 8 ways, conditioner controller
X95| Connector 9 ways, conditioner controller
X99| Connector 3 ways, thermostat
XA1.2| Connector 2 ways, alternator
XA1.1| Connector 1 way, alternator
XC1| Connector 18 ways, controller
XC2| Connector 21 ways, axles
XC3| Connector 6 ways, controller
XC4| Connector 21 ways, controller
XC5| Connector 12 ways, controller
XC6| Connector 15 ways, controller
XC7| Connector 21 ways, controller
XC8| Connector 18 ways, controller
X15| Connector 6 ways, deutsch rh rear light
X13| Connector 6 ways, deutsch lh rear light
Xi3| Connector 3 ways, thermostats

LIST OF COMPONENTS

COMP.| DESIGNATION| DIA.| COMP.| DESIGNATION| DIA.
---|---|---|---|---|---
B| Button, rexroth pilot valve| 4| M4| Pump, front windshield washer| 8
BS1| Rh loud speaker| 9| M5| Motor, rear wiper| 8
BS2| Lh loud speaker| 9| M7| Fan| 9
EVA2| Sol. valve, steering A2| 3| M8| Electric fan| 10
EVB2| Sol. valve, steering B2| 3| M9| Compressor| 10
FG1.1| Fuse, general 80 Amp| 3| S131| Switch, heating| 9
FG1.2| Fuse, general 80 Amp| 3| S15| Switch, rear axle release| 4
FG2| Fuse, conditioner 30 Amp| 1| R3| Filter thermistor| 1
FG3| Fuse, filter pre heater 20 Amp| 10| R2| Cold starter| 1
FV1| Fuse, variator 40 Amp| 10| K300| Relay, climate| 10
G| Button, rexroth pilot valve| 4| K301| Relay, thermostat| 10
G1| Battery| 1| S1| Micro, parking brake| 5
G2| Alternator| 1| S11| Switch, lh stabiliser| 5
H| Button, rexroth pilot valve| 4| S12| Switch, levelling| 5
H1| Light, front lh| 6| S13| Switch, rh stabiliser| 5
H11| Light, work rear rh| 7| S14| Switch, attachments| 7
H12| Rotary beacon| 7| S15a| Dashboard, starting| 1
H13| Light, cigarette lighter| 9| S2| Switch, rotary beacon| 7
H14| Ceiling light| 9| S3| Switch, warning| 6
H15| Lighting| 9| S30| Battery cut off, keyed| 1
H2| Light, front rh| 6| S31| Fuel level| 1
H3| Light, rear lh| 6| S61| Switch, steering selector| 3
H4| Light, rear rh| 6| S33| Sensor, rear axle| 3
H19| Light, licence plate| 6| S35| Sensor, lh stabiliser| 5
H6| Light, work boom| 7| S36| Sensor, rh stabiliser| 5
H7| Light, work boom| 7| S15| Switch, rear axle release| 4
H8| Light, work front rh| 7| S38| Sensor, low boom| 3
H9| Light, work front lh| 7| S39| Sensor, boom retracted| 3
HA1| Back up alarm| 2| S4| Switch, lights| 6
HX| Lighting, climate| 10| S64| Level, brake oil| 6
I1| Pressure switch, transmission oil| 1| S5| Switch, front work lights| 7
I10| Pressure switch, conditioner| 10| S50| Switch, climate| 10
I13| Thermostat| 10| S51| Switch, 4 gearshift + horn| 2
I2| Thermostat, transm. oil high pressure| 1| S52| Switch, lights direction wiper| 6
I3a| Thermistor, glow plugs| 1| S6| Switch, rear work lights| 7
I3b| Transducer, engine coolant temperat.| 1| S7| Switch, boom work lights| 7
I4| Pressure switch, engine oil low| 1| S8| Switch, upper/front wiper| 8
I7| pressure
Filter thermistore|
1| S9 S310| Switch, rear wiper
Sensor, tachometer| 8
5
I8| Pressure switch, parking brake| 5| SCX| Switch, climate| 10
K103| Relay, electric fan 1st speed| 10| XA4| Horn| 2
K105| Relay, electric fan 2nd speed| 10| X53| Cigarette lighter| 9
K107| Relay, electric fan 3rd speed| 10| X54| Refrigerator socket| 9
KA| Relay, starting| 1| S65| Micro, stop lights| 6
KB| Relay, conditioner| 10| Y1| Sol. valve, lh stabiliser lowering| 5
KC| Relay, filter preheating| 1| Y10| Sol. valve, optional (out)| 4
KD| Relay, under key| 1| Y11| Sol. valve, pilot controls| 4
KT| Relay, cold starting| 1| Y13| Sol. valve, reverse| 2
M1| Starter motor| 1| Y14| Sol. valve, forward| 2
M11| Recycling| 10| Y15| Sol. valve, gearshifting| 2
M12| Valve| 10| Y16| Sol. valve, 1st speed| 2
M13| Cooling fan| 10| Y17| Sol. valve, 2nd speed| 2
M14| Solenoid valve| 10| Y18| Sol. valve, engine cut off| 1
M2| Motor, front wiper| 6| Y19| Sol. valve, attachments| 7
| | | Y2| Sol. valve, lh stabiliser lifting| 5
COMP.| DESIGNATION| DIA.
---|---|---
Y3| Solenoid valve, rh stabiliser lowering| 5
Y4| Solenoid valve, rh stabiliser lifting| 5
Y5| Solenoid valve, lh levelling| 5
Y6| Solenoid valve, rh levelling| 5
Y8a| Solenoid valve, rh levelling| 5
Y8b| Solenoid valve, rh levelling| 5
Y9| Solenoid valve, optional (in)| 4

WIRE COLOUR KEYS

A………………………Azure
B…………………….. White
C…………………….. Orange
G ……………………..Yellow
H……………………..Grey
L……………………..Blue
M……………………..Brown
N……………………..Black
R……………………..Red
S……………………..Pink
V…………………….. Green
Z ……………………..Purple

NOTE: wires with two colours have compound acronyms, e.g.:
G/V – – Yellow/green (cross colouring)
G–V – – Yellow–Green (longitudinal colouring)

HOW TO USE THE CIRCUIT DIAGRAMS
The circuit diagrams have been drawn in a linear format, meaning that the complete vehicle system is drawn over a number of pages, with references to link the pages, where applicable. The flow of power is generally speaking, from top, positive, to bottom, negative.
Here are a number of explanations to the layout and references contained within the diagrams:

  1. All diagrams are located on the right hand pages.
    Within the diagram there are a number of references.

  2. Diagram number and electric function

  3. Line reference

  4. Component identification reference

  5. Connector x70, connector code, 3, references (pin)

  6. Wire colour code

  7. Fuse code. G1, fuse number, 10A, capacity

  8. Line continues on another diagram. In this instance: diagram 3 at line reference 1

  9. Alphabetical wire colour key

  10. Diode

  11. Component pin code

  12. Each component and connector appears only once in a set of circuit diagrams.

  13. The circuit diagrams are broken up into sections.
    However, where single component is used in a number of circuits, such as a processor or multi-function switch, it is drawn either on its own or in the circuit which it influences the most.

DIAGRAM 1 – STARTING/RECHARGE/WARNING LAMPS/INDICATORS  New Holland
LM1330-1333 Electric Wiring Diagrams - Diagram 1 DIAGRAM 1 – STARTING/RECHARGE/WARNING /INDICATORS LIGHTS

COMPONENTS AND FUSES DESCRIPTION
F1 Fuse, relay KC power 5 Amp
F28 Engine cut off 10 Amp
FG2 Fuse, conditioner 30 Amp
G1 Battery
G2 Alternator
I1 Pressure switch, transmission oil
I2 Thermostat, transmission oil high temperature
I3a Thermistor, glow plugs
I3b Transducer, engine coolant temperature
I4 Pressure switch, engine oil low pressure
I7 Filter thermistor
K19 Relay, engine cut off
KA Relay, starting
KC Relay, filter preheating
KD Relay, under key
KT Relay, cold starting
M1 Starter motor
R2 Cold starting
R3 Filter thermistor
S15a Starting dashboard
S30 Keyed battery cut off
S31 Fuel level
Y18 Solenoid valve, engine cut off

DIAGRAM 1 – STARTING/RECHARGE/WARNING LAMPS/INDICATORS New Holland
LM1330-1333 Electric Wiring Diagrams - Diagram 2DIAGRAM 2 – TRANSMISSION

COMPONENTS AND FUSES DESCRIPTION
F18 Fuse, horn 15 Amp
F33 Fuse, safety gears + parking brake 10 Amp
F34 Fuse, back up alarm 5 Amp
F37 Fuse, high beam lights 15 Amp
HA1 Back up alarm
HA4 Horn
K13 Relay, 2nd speed
K15 Relay, telescopic retraction
K20 Relay, horn
K22 Relay, 1st speed
K23 Relay, forward speed
K24 Relay, 4th speed
K5 Relay, gearshifting safety
K6 Relay, back up alarm
K7 Relay, telescopic motion
S51 Switch, 4 speed gearshift + horn Hobbs
Y13 Solenoid valve, reverse speeds
Y14 Solenoid valve, forward speeds
Y15 Solenoid valve, gearshifting
Y16 Solenoid valve, 1st speed
Y17 Solenoid valve, 2nd speed

DIAGRAM 2 – TRANSMISSION New Holland LM1330-1333 Electric Wiring
Diagrams - Diagram 3DIAGRAM 3 – WHEEL ALIGNMENT/HYDRAULIC SOLENOIDS/BRAKE SYSTE M

COMPONENTS AND FUSES DESCRIPTION
EVA2 Solenoid valve, steering A2
EVB2 Solenoid valve, steering B2
F10 Fuse, rear axle release 10 Amp
F17 Fuse, low boom sensor 10 Amp
F5 Fuse, stabilisers lowering 7.5 Amp
F6 Fuse, rear axle sensor 7.5 Amp
FG1.1 Fuse, general 80 Amp
FG1.2 Fuse, general 80 Amp
K10 Relay, levelling
K2 Relay, stabilisers safety
K3 Relay, stabilisers
K9 Relay, low boom sensor
S33 Sensor, rear axle
S38 Sensor, low boom
S39 Sensor, boom retracted
S61 Switch, steering selector

DIAGRAM 3 – WHEEL ALIGNMENT/HYDRAULIC SOLENOIDS/BRAKE SYSTEM New
Holland LM1330-1333 Electric Wiring Diagrams - Diagram 4DIAGRAM 4 – BOOM CONTROL

COMPONENTS AND FUSES DESCRIPTION
B Button, Rexroth pilot valve
F12 Fuse, extension/retraction 15 Amp
F21 Fuse, option in/out 10 Amp
G Button, Rexroth pilot valve
H Button, Rexroth pilot valve
K14 Relay, reverse
K21 Relay, option “n”
K4 Relay, option “out”
S15 Switch, rear axle release
Y10 Solenoid valve, optional (out)
Y11 Solenoid valve, pilot controls
Y9 Solenoid valve, optional (in)

**DIAGRAM 4 – BOOM CONTROL![New Holland LM1330-1333 Electric Wiring Diagrams

COMPONENTS AND FUSES DESCRIPTION
F32 Fuse, lights 3 Amp
I8 Pressure switch, parking brake
K12 Relay, parking brake
S1 Micro, parking brake
S11 Switch, lh stabiliser
S12 Switch, levelling
S13 Switch, rh stabiliser
S310 Sensor, tachometer
S35 Sensor, lh stabiliser
S36 Sensor, rh stabiliser
Y1 Solenoid valve, lh stabiliser lowering
Y2 Solenoid valve, lh stabiliser lifting
Y3 Solenoid valve, rh stabiliser lowering
Y4 Solenoid valve, rh stabiliser lifting
Y5 Solenoid valve, lh levelling
Y6 Solenoid valve, rh levelling
Y8a Solenoid valve, rh levelling
Y8b Solenoid valve, rh levelling
Y9 Solenoid valve, optional (IN)

DIAGRAM 5 – STABILISER ![New Holland LM1330-1333 Electric Wiring Diagrams

COMPONENTS AND FUSES DESCRIPTION
F11 Fuse, stop micro 5 amp
F14 Fuse, warning 10 Amp
F23 Fuse, rear wiper 10 Amp
F24 Fuse, tail lights + licence plate 5 Amp
F36 Fuse, head lights 5 Amp
F38 Fuse, low beam 15 Amp
H1 Light, front lh
H19 Light, licence plate
H2 Light, rh front
H3 Light, lh rear
H4 Light, rh rear
K16 Relay, high beam
K18 Flasher
M2 Motor, front wiper
S3 Switch, warning
S4 Switch, lights
S52 Switch, lights direction wiper
S64 Level, brake oil
S65 Micro, stop lights

DIAGRAM 6 – LIGHTS/FRONT WIPERNew Holland LM1330-1333 Electric Wiring
Diagrams - Diagram 7 DIAGRAM 7 – WORK LAMPS/ROOF BEACON LIGHT

COMPONENTS AND FUSES DESCRIPTION
F15 Fuse, rotary beacon 10 Amp
F22 Fuse, boom work lights
F31 Fuse, attachments
F35 Fuse, rear work lights 15 Amp
F9 Fuse, front work lights 15 Amp
H11 Light, work rear rh
H12 Rotary beacon
H6 Light, work boom
H7 Light, work boom
H8 Light, work front rh
H9 Light, work front lh
S14 Switch, attachments
S2 Switch, rotary beacon
S5 Switch, front work lights
S6 Switch, rear work lights
S7 Switch, boom work lights
Y19 Sol. valve, attachments

DIAGRAM 7 – WORK LAMPS/ROOF BEACON LIGHT New Holland LM1330-1333
Electric Wiring Diagrams - Diagram 8DIAGRAM 8 – LOAD MOMENTUM DEVICE / UPPER WIPER

COMPONENTS AND FUSES DESCRIPTION
F19 Fuse, rear wiper 10 Amp
F29 Fuse, platform ON 15 Amp
F30 Fuse, load momentum instrument 5 Amp
F7 Fuse, upper wiper 10 Amp
K1 Relay, 100% motion cut
K17 Controller
K8 Relay, low beam lights
M4 Pump, front window washer
M5 Motor, rear wiper
S8 Switch, upper/front wiper
S9 Switch, rear wiper

DIAGRAM 8 – LOAD MOMENTUM DEVICE / UPPER WIPER New Holland LM1330-1333
Electric Wiring Diagrams - Diagram 9DIAGRAM 9 – HEATING / RADIO / POWER SOCKET / CEILING LIGHT

COMPONENTS AND FUSES DESCRIPTION
BS1 Rh loudspeaker
BS2 Lh loudspeaker
F26 Fuse, ceiling light 5Amp
F3 Fuse, radio 3 Amp
F39 Fuse, cigarette lighter 20 Amp
F8 Fuse, heating 15 Amp
H13 Light, cigarette lighter
H14 Ceiling light
H15 Lighting
M7 Fan
S131 Switch, heating
X53 Cigarette lighter
X54 Socket, refrigerator

DIAGRAM 9 – HEATING / RADIO / POWER SOCKET / CEILING LIGHTNew Holland
LM1330-1333 Electric Wiring Diagrams - Diagram 10 DIAGRAM 10 – CONDITIONER

COMPONENTS AND FUSES DESCRIPTION
F13 Fuse, optional 5 Amp
F16 Fuse, optional 10 Amp
F2 Fuse, conditioner 3 Amp
F20 Fuse, optional 10 Amp
F25 Fuse, optional 7.5 Amp
F27 Relay, compressor 10 Amp
F4 Fuse, optional 3 Amp
FG3 Fuse, filter preheating 20 Amp
FV1 Fuse, variator 40 Amp
HX Lighting, climate
I10 Pressure switch, conditioner
I13 Thermostat
K103 Relay, electric fan 1st speed
K105 Relay, electric fan 2nd speed
K107 Relay, electric fan 3rd speed
K11 Relay, steering selector
K300 Relay, climate
K301 Relay, thermostat
KB Relay, conditioner
M11 Recycling
M12 Valve
M13 Fan, cooling
M14 Electric fan
M8 Electric fan
M9 Compressor
S50 Switch, climate
SCX Switch, climate

**DIAGRAM 10 – CONDITIONER![New Holland LM1330-1333 Electric Wiring Diagrams

Documents / Resources

| New Holland LM1330-1333 Electric Wiring Diagrams [pdf] User Manual
LM1330-1333 Electric Wiring Diagrams, LM1330-1333, Electric Wiring Diagrams, Wiring Diagrams, Diagrams
---|---

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals