JASCO 76721 Plug In Outdoor Smart Switch Instruction Manual

JASCO 76721 Plug In Outdoor Smart Switch

Thank you for your purchase!

FEATURES

Must not exceed 1250W (10A) incandescent, 1875W (15A) resistive or 1/2HP motor

• One Z-Wave controlled AC outlet for outdoor devices and lighting
• Remote ON/OFF operation via the Z-Wave controller
• Manual ON/OFF control with the front-mounted push button
• Space-efficient design
• Grounded three-wire power connection for safety
• This Z-Wave device has advanced features that allow you to customize your experience. These features can only be adjusted by a Z-Wave enabled controller that supports the Z-Wave configuration command class. For a complete list of adjustable configurations, visit www.ezzwave.com/config
• Supports Z-Wave Long Range — requires Z-Wave hub that supports 2-Wave Long Range
• Can be added as a Z-Wave Long Range or standard Z-Wave device

A. Z-Wave controlled outlet

• This outlet can remotely turn the connected light or appliance ON/OFF

B. Manual/program button

• Single press – turn ON/OFF
• Single press – add or remove in Z-Wave network

ADDING YOUR DEVICE

ADDING YOUR DEVICE TO A Z-WAVE NETWORK

1. Follow the instructions for your Z-Wave certified controller to add a device to the Z-Wave network.
2. Once the controller is ready to add your device, press the program button of the smart switch.

You have complete control to turn your device ON/OFF according to groups, scenes, schedules and interactive automations programmed by your controller. If your Z-Wave certified controller features remote access, you can control your lamp from your mobile devices. If prompted by the controller to enter the S2 security code, refer to the QR code/security number on the side of the box or the QR code label on the product (see Example 1). Enter the 5-digit code.

Example 1

TO REMOVE AND RESET THE DEVICE

1. Follow the instructions for your Z-Wave certified controller to remove a device from the Z-Wave network.
2. Once the controller is ready to remove your device, press the program button of the smart switch.

TO RETURN YOUR SWITCH TO FACTORY DEFAULTS

1. If plugged in, unplug the switch from the receptacle.
2. Press and hold the program button for at least three seconds while you plug the switch into a receptacle.

NOTE: This should only be used if your network’s primary controller is missing or otherwise inoperable.

NOTE: SmartStart enabled products can be added into a Z-Wave network by scanning the QR code on the product with a controller providing SmartStart inclusion. No further action is required and the SmartStart product will be added automatically within 10 minutes of being switched on in the network vicinity.

SPECIFICATIONS

IMPORTANT: ZWN4204

• Power: 125VAC, 60Hz
• Signal (frequency): 908.4/916MHz
• Maximum load: 1250W (10A) tungsten, 1/2HP motor or 1875W (15A) resistive
• Wireless range (Classic): Up to 150ft. line of sight between the wireless controller and the closest Z-Wave receiver module
• Wireless range (Long Range): Up to 1300ft. line of sight to the wireless controller
• Operating temperature range: 14-104 F (-10-40 C)
• For outdoor use

Specifications subject to change without notice due to continuing product improvement

NOT FOR USE WITH MEDICAL OR LIFE-SUPPORT EQUIPMENT

Z-WAVE ENABLED DEVICES SHOULD NEVER BE USED TO SUPPLY POWER TO OR CONTROL THE ON/OFF STATUS OF MEDICAL OR LIFE-SUPPORT EQUIPMENT.

PLUGGING IN YOUR Z-WAVE DEVICE

IMPORTANT

• This unit is suitable for outdoor use in damp locations.
• Do not expose to rain or immerse in water. Install at least 1ft. above ground level with the receptacle pointed down. When used outdoors, plug the unit into a GFCI outlet with a receptacle cover rated for outdoor use.

• Install the included screw in the desired location leaving 3/16in. of the screw exposed. Align the mounting loop with the screw head, slide the loop over the screw and allow the unit to hang with the outlet facing downward.

The manual/program button on the smart switch allows the user to:

1. Manually turn ON/OFF the connected device.
2. Add/remove the smart switch from the network.

NOTE: Plug directly into GFCI-protected receptacle outlet. Do not use with extension cords.

WARRANTY

Jasco Products Company warrants this product to be free from manufacturing defects for five years from the original state of consumer purchase. This warranty is Imited to the repair or replacement of this product only and does not extend to consequential or incidental camage to other products that may be used with this product. This warranty is instead of all other warranties, expressed or implied, Some states do not allow Imitations on how long an implied warranty lasts or permit the exclusion or limitation of incidental or consequential damage, so the above Imitations may not apply to you.

This warranty gives you specific rights and you may also have other rights which vary from state to state, Please contact our US.-based Consumer Care at 1-800-654-8483 (option 1), M-F, 7AM-8PM Central Time or www.byjasco.com if the unit should prove defective within the warranty period.

WARNING

RISK OF FIRE
RISK OF ELECTRICAL SHOCK
RISK OF BURNS

TO REDUCE THE RISK OF ELECTRIC SHOCK, THIS PRODUCT HAS A GROUNDING PLUG THAT HAS A THIRD (GROUNDING) PIN. THIS PLUG WILL ONLY FIT INTO A GROUNDING TYPE POWER OUTLET. IF THE PLE DOES NOT CHANTO OUTLET CONTACT QUALIFIED ELECTRICIAN TO INSTALL THE PROPER CONTROLLING APPLIANCES.

CAUTION: TO REDUCE THE RISK OF OVERHEATING AND POSSIBLE DAMAGE TO OTHER EQUIPMENT

• DO NOT EXE FEDCONTROL ANY DEVICE WHERE UNINTENDED OPERATION COULD CAUSE
• UNSAFE CONDITIONS (HEAT LAMP, SUN LAMP, ETC.)
• PORNOOSE USE TENSION CORDS
• FOR INDOOR USE ONLY

FCC STATEMENT

FCC/IC

Suppliers Declaration of Conformity | Model #: 76722 | Jasco Products Co. 10 E. Memorial Rd. Oklahoma City, OK 73114, www.byjasco.com

This device complies with Part 15 of the FCC rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

FCC NOTE: The manufacturer is not responsible for any radio or TV interference caused by unauthorized modifications to this equipment. Such modifications could void the user’s authority to operate the equipment.

NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning blowing measurf and on, the user is encouraged to try to correct the interference by one or more of the

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

CAN ICES-3(B)/NMB-3(B)

RF WARNING FOR PORTABLE DEVICE

• The device has been evaluated to meet general RF exposure requirement. The device can be usedin portable exposure condition without restriction.
• This equipment should be installed and operated with minimum distance 0cm between the radiator & your body.

Z-WAVE INTEROPERABILITY

This product can be included and operated in any 2-Wave network with other 2-Wave certified devices from other manufacturers and/or other applications. All non-battery-operated nodes within the network will act as repeaters regardless of vendor to increase reliability of the network.

This device supports association command class (3 Groups)

• Association Group 1 supports Lifeline, Binary Switch Report
• Association Group 2 supports Basic Set and is controlled by pressing the ON or OFF button with the local load
• Association Group 3 supports Basic Set and is controlled by double pressing the ON or OfF button
• Each Association Group supports 5 total nodes

More Information

Instructions made easy

• Read instructions or watch easy-to- follow video.
• Scan code or visit byjasco.com/76722i.

Register your product

• Receive exclusive deals and register your product.
• Scan code or visit byjasco.com/deals.

For additional JascoPro Series products, visit our website www.jascopro.com.

Like our product?

• Leave a review on your favorite retailer website or amazon.com.

Having problems?

• Let us know how we can help.
• Call 1-800-654-8483 between 7AM-8PM, M-F, Central Time.

For product patent information, visit www.byjasco.com/patents.
All brand names shown are trademarks of their respective owners.

MADE IN VIETNAM

Distributed by Jasco Products Company LLC, 10 E. Memorial Rd., Oklahoma City, OK 73114.
This Jasco product has a 5-year limited warranty. Visit www.byjasco.com for warranty details.
Questions? Contact our U.S.-based Consumer Care at 1-800-654-8483, M-F, 7AM-8PM Central Time.

©JASCO 2023 | ZWN4204 | 76722 | 08/11/23 v1

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>