BILT HARD HFB-0406 24 Inch High Velocity Industrial Wall Fan Owner’s Manual

BILT HARD HFB-0406 24 Inch High Velocity Industrial Wall Fan

READ & SAVE THESE INSTRUCTIONS

SAFETY INFORMATION

WARNING

1. Read and save these instructions. Do not operate fan unless you have read these instructions.
2. Unplug the fan before moving it or performing maintenance. Do not touch the fan when your hands are wet.
3. Those who are not qualified electricians should not disassemble, repair or rebuild the fan.
4. Unplug the fan when it is not in use.
5. DO NOT unplug the fan by pulling the cable cord. Unplug by holding the plug and pulling.
6. DO NOT use the fan when there is damage to the cable cord or plug. If the supply cord is damaged, it has to be replaced by the Manufacturer, its service agent or similarly quailed persons.
7. DO NOT use the fan with mansion cord.
8. DO NOT use the fan close to fires.
9. DO NOT insert your hand or other objects into the grille or the movable pans.
10. To reduce the risk of fire or electric shock, do not use this fan with any solid state speed control device.
11. DO NOT use this fan outdoors, this fan is designed for indoor use only.

CAUTION

1. Unplug the fan from the socket and clean it with a soft cloth.
2. DO NOT immerse the fan.
3. Fit the guard onto fan before starting up the fan.
4. This fan is not intended for use by people (including children) with reduced physical, sensory or mental capabilities or lack of experience and knowledge unless they have been given supervision or instruction concerning use of the fan by a person responsible for their safety. Supervise children to ensure they do not play with the fan.

PACKAGE CONTENTS

FAN PARTS

1. Front Guard, 1PCS
2. Rear Guard, 1PCS
3. Fan Blade, 1PCS
4. Motor, 1PCS
5. Wall Bracket, 1PCS
6. Screw list of connection between Motor and Wall Bracket
7. Screw M12X120, 1PCS
8. Screw M12X30, 1PCS
9. Screw M8X25, 1PCS
10. Flat washer Ø12, 2PCS
11. Spring washer Ø12, 2PCS
12. Hexangular Nu t M12, 2PCS
13. Hexangular Nu t M8, 1PCS
14. Screw ST6X50 bolt, 3PCS
15. Wall Anchor, 3PCS
16. Joint Kit, 1PCS
    

ASSEMBLY INSTRUCTION

Step 1:

1. Mark the hole locations by using the bracket, and then drill the hole s.
2. For concrete wall installation, after drilling, you would insert the wall wall, position the bracket and then screw the two bolts into the anchors, securely attaching the wall anchors and tap them flush with me wall, position the bracket and then screw the two bolts into the anchors, securely attaching the wall.
3. For wall stud installation, after drilling the smaller diameter pilot hole, position the bracket and screw the two bolts into the wall until they are secured.

CAUTION: The fan is only suitable for concrete wall. Do not use for dry wall mounting. Use the mounting accessories shipped with products for wall mounting.

• a. concrete wall
  

• b. wall stud
  

Step 2:

Remove four sets of Hexagonal Nuts, Spring Washers and Big Washers from Motor. Save them for Step 3.

Step 3:

Set Rear Guard in the proper position, and fix It to Motor by securing back the Hexagonal Nuts, Spring Washers and Big Washers from Sept 2.

Step 4:

Assemble Fan Blade onto Motor Shaft by tightening two screws which located on Fan Blade. Make sure the screw is tightly secured.

Step 5:

Assemble Front Guard to Rear Guard by fixing both Guards together with clips.

Step6:

Secure the assembly of Front guard and rear guard by tightening a screw and nut on the bottom position of them.

Step 7:

Connect No.3 Joint Kit with Fan Head by No.1 Screw M12X30, No.7 Spring Washer φ12, No.6 Flat Washer φ12 and No.5 Hexangular Nut M12. Then, fasten No.2 Screw M8X25 with Hexangular Nut M8 through the Joint Kit for holding the vertical degree between Fan Head and Wall Bracket.

Step 8:

Assemble the Fan Head with Wall Bracket by inserting No.1 Screw M12X120 through the Joint Kit, and fastening them by No.2 Spring Washer φ12, No.4 Flat Washer φ12 and No.3 Hexangular Nut M12.

Step 9:

Loose Hexangular Nut M8 for adjusting the desired tilt angle of fan head, and fix it again.

OSCILLATION INSTRUCTIONS

To make the fan head oscillate: loosen the screw and move the position A. Tighten it back.
Note: the screw is preset at position A at the factory.

To stop the fan head oscillate : loosen the screw and move to position B. Tighten it back.
Caution: Switch off the fan before adjusting fa n head oscillation.

• Position A-To make the fan head oscillate
  

• Position B -To stop the fan head oscillate
  

INSTALLATION SECONDARY SAFETY SUPPORT CABLE

Warning :
Use of secondary safety support cable does not guarantee protection against injury of persons. Mounting of both the circulator and cable could fail if subject to abuse, neglect or if improperly installed. To avoid personal injury, circulators must be supported anytime angle is adjusted.

CAUTION: The fan is only suitable for concrete wall. Do not use for dry wall mounting. Use the mounting accessories shipped with products for wall mounting.

1. Loop one end of the cable around the large diameter wires of both the front and rear guard as shown below. Attach a cable retainer with the ”U” on the tail side of the loop leaving a tail of approximately 1 to 2 inches. Tighten clamp nuts forming a tight loop, 32in. lbs of torque. Make sure the cable does not interfere with the propeller.
   

2. Drill a hole in concrete wall, insert the wall anchor and tap it flush with the wall.
   

3. Fasten a blot and a washer through the terminal of secondary safety support cable into the anchor for security.
   

4. Check the assembly to assure the propeller is free of all obstructions and turns freely.

5. Connect the circulator to the proper power supply ensuring that it conforms to the electrical rating listed on the circulator’s motor nameplate.

OPERATION INSTRUCTION

1. Place the fan on a safe, at surface where it cannot fall or be pulled by the cord.
2. To adjust air flow upward or downward: Tilt the fan head to the desired angle.
3. Turn the rotary switch for desired speed. 0=Off,1=Low, 2=Med, 3=High
4. Always turn off and unplug the fan after using.

CARE AND MAINTENANCE

Unplug the appliance before cleaning. Don’t use any water for cleaning metal surfaces. Slightly moisten a cloth and then wipe off the surfaces of the fan. In order to remove dust from 1he grill, use a vacuum cleaner or remove the front grill by removing 111e securing screws on the edge of the grill. After cleaning, remount the grill. After doing this, fasten the screws on the edge of the grill.

Customer Support

Questions, problems, missing parts?
Before returning to the store please call customer service at 888-680-2849
EMAIL: inquiry@bilthardusa.com
Monday through Friday 8:00 AM to 5:00 PM CST

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>