Pewkim B0C6J6P3TG Dog Training Collar User Guide
- June 16, 2024
- Pewkim
Table of Contents
Pewkim B0C6J6P3TG Dog Training Collar
Operation Guide
Please read the entire guide before using”.
Thanks for choosing the Rechargeable and Waterproof Remote Dog Training Collar. Our mission is to provide you with the safe tools and techniques to train your dog.
Features
1. Rechargeable Remote Transmitter
2. Rechargeable and Waterproof Receiving Collar
3. 2600 feet ( 800 meters) remote control range between Remote Transmitter
and Receiving Collar.
4. Beep Mode activates a correcting tone on the Receiving Collar
5. Adjustable vibration intensity level from 1-99 level.
6. Adjustable static shock intensity level from 1-99 level.
7. Adjustable beep loudness level from 1-9 level.
8. Power saving modes:
- The Receiving Collar will go into Standby Mode if is idle for more than 5 mins.
- The Transmitter will go into Standby Mode ( 8 will be light off with 30s, The LED sawn will be light off with 3mins ). Press any button to re-activate it from Standby mode.
9. The Remote Transmitter can be used to control up to 3 Receiving Collars.
10.2 pairs of metal contacts (1 short and 1 long) are included to suit the
length of your dog’s hair.
11. The Transmitter with lock key function.
How does the Rechargeable and Waterproof Dog Training Collar Work
The Rechargeable and Waterproof Training Collar has been proven to be a safe, comfortable, and effective training system for all dogs weighing over 151bs. This system allows you to control your dog within a range up to 2600 feet. At the press of a button, the Remote Transmitter sends signal to the Receiving Collar and activates a Beep, a Vibration or a Static Shack correction output. By using the Training Collar properly, you can correct much of your dog’s undesired behavior and teach basic and advanced obedience commands.
Important: the Training Collar has an effective range up to 2600 feet. Hold the Remote Transmitter horizontally away from your body to achieve the optimum range. Terrain features, weather, vegetation, transmission from other radio devices and other factors may affect the range of the Remote Transmitter.
Precautions
DO NOT use this product for aggressive dogs or vicious animals.
Risk of skin damage.
It’ s important to fit the collar properly. A collar that is fitted too tightly or worn for too long may harm your dog’s skin. This condition, which ranges from redness to pressure ulcers, is commonly known as bed sores.
CAUTION
- Do not let your dog wear the collar for more than 12 hours per 24-hour period.
- if possible, gently reposition the collar on your dog’s neck every 1 or 2 hours.
- Never attach a lead to the Receiver Collar, as this would cause excessive pressure on the contact points.
- When using a separate collar to connect a leash, please ensure that it does not put excessive pressure on the electronic collar.
- Examine your dog’s neck daily for signs of chafing or soreness.
- if a rash or sore is found, stop using the collar fill the injured skin has been healed.
- if the condition persists for more than 48 hours, consult your veterinarian.
- if possible, please use the Beep Mode or Vibration Mode at first, then can try Static shock function.
Please ensure that you charge both the Receiving collar and the Remote Transmitter before using!
To extend the battery life of this product,if you do not intend to use it for a long period of time, please charge them per month.
Components
How to change the contact point to the Receiver Collar
Key Definition
1. ED Screen:
- Beep Mode: When this symbol is displayed, press the button to active a Beep tone on the Receiving Collar. Use the UP/ Down buttons to adjust the loudness of the beep form 1 to 9.
- Vibration Mode: When this symbol is displayed, press the button to activate Vibration. Use the Up/Down buttons to adjust the intensity of the vibration from 1 to 99.
- Static Shock Mode: When this symbol is displayed, press the button to activate Static Shock. Use the Up/Down buttons to adjust the intensity of the vibration from 1 to 99.
- Channel 1/2/3: Select 1/2/3 channel to encode the Receiving Collar 1/2/3.
- Transmitter Battery: When this symbol is on display when charging, means the battery is in full.
- Receiver Battery: When this symbol is on display, means the Transmitter and Receiver encoded successfully.
2. Key Lock: When this symbol is displayed, means the transmitter is under
key lock.
3. Launch Button: Use to send a command to receiver and to confirm when
pairing.
4. Mode button: Press this button to select mode among Beep, Vibration or
Static Shock.
5. Level Up/Down Button: Adjusts the intensity of the sound, vibration or
static shock.
6. Channel button: Press this button to change between the 1-3 Receiving
Collar (if applicable).
7. Charging port: Plug the USB charging cable into the port to charge the
Remote Transmitter.
- Lithium battery: 3.7V 500mAh for the Remote Transmitter 3.7V 500mAh for the Receiving Collar Operating Frequency: RF433 MHZ
- Contact points: 2 pairs of metal contacts to be chosen to suit the length of your dog’s hair.
- Mini Spanner: a tool to screw/unscrew contact points on the electrodes.
Contact Points:
Deliver vibmtion / safe static correction
Operation Guide
Step 1: Preparing the Remote Transmitter:
Charging the Remote Transmitter with USB Charging Cable.
- Plug the USB Charging Cable into the Charging port.
- Plug the Adapter into a standard outlet.
- Three battery bars of the symbol is running circularly when charging.
- The LED screen will show once its full charged with 2.5 hours. Remove the USB charging cable.
Low battery indicator: This symbol will flash 30seconds, then transmitter will be tumed off automatically.
How to use the Remote Transmitter
- Push down the key lock switch, the LED screen light up.
- Use the Mode button to cycle through different modes. The LED screen will display which mode is currently actived ). Press the Y button to launch Beep, Vibration or Static Shock signal.
- Press the Up/ Down buttons to set the intensity of the vibration or shock, or adjust the loudness of beep.
- Select different channels for 1 or 3 Receiving Collars.
Power Saving Mode: the Remote Transmitter will go into Standby Mode if it is idle for 3 mins. The LED screen on the Remote Transmitter will not display anything in this cese(g will be light off with 305, The LED screen will be light off with 3mins), press any button to re-activate it.
Lock Key function: Push up the lock switch, the ( ) will flash for 6 seconds then it goes into key lock mode, and it won’t be activated anymore, the ( ) will flash for 6 seconds again if any button be pressed.Push down the lock switch, the Transmitter will become active again.
Step 2: Paring the Receiving Collar:
Charging the Receiving Collar with USB Charging Cable
- Remove the rubber cover and plug the USB Charging Cable into the charging port.
- Plug the Adapter into a standard outlet.
- The red LED will keep lighting when the Receiving Collar is charging.
- The green LED will be lighting once it’s fully charged with 2.5 hours.
- Remove the Charging Cable, and put back the rubber cover.
Low battery indicator:
The red LED will be flash with 30seconds, then Receiving Collar will be tumed off automatically.
How to use the Receiving Collar:
Press the On/Off button to tum the Receiving Collar on. The green LED will illuminate to confirm that the Receiving Collar is ON. The red LED lighting means the Receiving Collar is off. Press and hold the button, The green and red LED will flash, means that it waits for encoding.
Power Saving Mode:
The Receiving Collar will go into Standby Mode if it is idle for more than 5 mins. Any movements will activate the Receiving Collar. If the Receiving Collar does not be activated when you press the button on Transmitter, and the Green LED on receiving collar is not on, then gently shake the Receiving Collar, the Receiving Collar will be activated and the Green LED light will illuminate.
Step 3: Encoding the Remote Transmitter and the Receiving Collar:
- Push down the lock switch to make sure the Transmitter in on work status.
- Press the to choose either channel 1 or 2 or 3.
- Press and hold the on the Receiving Collar, When the green and red LED flash, then press the on the Transmitter, the LED lights tum from flashing to off and the Receiving Collar beeps. Encode successfully.
- When the green and red LED flash, not press the on the Transmitter within 10 mins, the LED lights tum from flashing to off. Please repeat step 3 to encode.
- Repeat steps 2-3 to encode other Receiving Collar(ff needed)Please wait at least 10 seconds to encode other Receive Collar.
Note: Most of the Rechargeable and Waterproof Training Collars have already been encoded before leaving the factory. If so, just press any button on the transmitter to activate, then press the with 1 sec on receiving collar to turn on it, after that, you can test the function refer to step 4. (Page 10)
Step 4: Testing the Rechargeable and Waterproof Training Collar:
Testing the Static Shock Function
The static impulse generated by the Receiving Collar cannot be seen by naked eyes. Test whether the Static Shock Function works by using the following procedure:
- Remove the Test Light from the package and connect it to the contact points on the receiving collar.
- Press the °Mode” button on Remote Transmitter to select Shock mode. Press the launch ( ) button to launch shock signal. If the Test Light flashes, the Static Shock Function is working correctly.
- Press and hold the button, the Receiving Collar will continuously generate static impulse. Press and hold the button for more than 8 seconds, the number on LED screen will flash, and the Transmitter stops launching signal. At this time, pressing any button is invalid. After 30 seconds, The transmitter will become active again.
- The intensity of the Static Shock can be adjusted by pressing Up/Down button ( ) from level 1 to 99.
Testing the Vibration Function
- Press the “Mode” button on Remote Transmitter to select Vibration mode. Press the launch ( ) button to launch vibration signal. If the Receiving Collar vibrates, the Vibration Function Is working correctly.
- Press and hold the button, the Receiving Collar will continuously vibrate. Press and hold the button for more than 8 seconds, the number on LED screen will flash, and the Transmitter stops launching signal. At this time, pressing any button is invalid. After 30 seconds, The transmitter will become active again.
- The intensity of the Vibration an be adjusted by pressing Up/Down button from level 1 to 99.
Testing the Beep Function
- Press the “Mode” button on Remote Transmitter to select Beep mode. Press the launch ( ) button to launch beep signal. If the Receiving Collar beeps, the Beep Function is working correctly.
- Press and hold the button, the Receiving Collar will continuously beep.
- Press and hold the button for more than 8 seconds, the number on LED screen will flash, and the Transmitter stops launching signal. At this time, pressing any button is invalid. After 30 seconds, The transmitter will become active again. tit
- The loudness of the beep can be adjusted by pressing Up/Down button from level 1 to 9.
Step 5: Fitting the Receiving Collar to your dog:
1. Center the Contact Points under your dog’s neck(A).
2. The Receiving Collar should be positioned snugly around your dog’s neck.
Important: Make sure that you can fit one finger between the strap and your dog’s neck(B).
Note: Choose the correct Contact Points to suit the length of your dog’s hair. If your dog has long hair or a thick coat, use the longer Contact Points.
FAQ – Frequently Asked Questions
Q1: How old does my dog have to be before I start using the Rechargeable and Waterproof Training Collar?
A: Your pet should be able to recognize basic commands such as °Sit!” and °Stay!”. The Rechargeable and Waterproof Training Collar may be too large for dogs weighing less than 151bs. The Receiving collar is adjustable in length from 9.5 to 26 inches. If your dog’s neck is smaller than 26 inches, please cut the redundant part. This product is not suitable for dogs with necks larger than 26 inches.
Q2: Once my dog is trained and has teamed to obey my commands, will he have to continue wearing the Receiving Collar?
A: Probably not, although you may need to reinforce the training with the Receiving Collar from time to time.
Q3: is the Receiving Collar waterproof?
A: Yes. In fact, your dog can swim while wearing the Receiving Collar Must seal well the charing port lightly, and keep it dry after get wet.
Q4: What is the lifespan of the lithium batteries?
A: The Lithium battery in the Remote Transmitter and the Receiving Collar can be charged for 400 times.
Q5: How long should the training session for my dog be?
A: The training sessions should be kept short for maximum effectiveness. It’s advised not to train your dog for more than 10-15 mins at a time.
I have fitted the Rechargeable and Waterproof Training Collar correctly, but my dog is not responding.
- Ensure that the batteries are fully charged. You need to charge both the Remote Transmitter and the Receiving Collar for about 2.5 hours before they can be used for the first lime.
- Check the Remote Transmitter can adjust the intensity level of the vibration or static shock to higher level more than level 1.
- Restart the Receiving collar by pressing the On/ Off button.
- Test the 3 functions (Beep, Vibration and Static Shock) before using the Receiving Collar for the first time. Please refer to “Step 4” (page 10) for instructions on how to do this.
- The Receiving collar will go into Standyby Mode if it is idle for more than 5 minutes. Any movements will re-activate it.
- Make sure that the Contact Points are touching your dog’s skin.
- Trim your dog’s fur where the Contact Points touch the neck. Ensure that you are using the correct set of Contact Points suitable for the length of your dog’s fur.
- if none of the above works, encode the Remote Transmitter and the Receiving Collar again. See “Step 3” (Page 10 ) for instructions on how to do this.
I am trying to test the Receiving Collar manually, but it does not work. If you want to test the Receiving Collar manually on your hand or leg, please touch the 2 Contact Points simultaneously. Touching only one of the Contact Points will not work.
The Receiving Collar is broken. It has not worked since I dropped it.
- The Receiving Collar is not designed to be drop-proof. Please do not drop the Receiving Collar, as this will damage the interior circuits.
The Remote Transmitter does not work
- You must charge the Remote Transmitter before you use it for the first time. Charging time is typically 2.5 hours.
- Ensure that the Remote Transmitter has adequate power.
- Remote Transmitter will automatically go into Standby Mode if it is idle for 3 mins. No LED light will be illuminated at this time. Press any button to re-activate the Remote Transmitter.
General Tips for Training Your Dog
- Eliminate one behavioral problem or teach one command at a time. If you move too fast with the training, your dog may become confused.
- Be consistent. Give your dog a single Beep, Vibration, or Static Shock for each misbehavior.
- Do not over-correct your dog. Use a few stimulations as possible during training.
- Unless you can supervise him/ her, It is recommended that you restrain your dog from environments in which he/ she has a history of misbehaving. However, setting up a training session in this case can dramatically improve your chances of success.
- if your dog reacts to the training by hiding or acting fearfully, redirect his/ her attention to a simple and appropriate behavior, such as Ihe”Sit!” command.
Common Weights of Different Dog Breeds
- Large Dogs(Body height over 61 cm, weight over 881bs)
- Medium Dogs( Height 40.7-61 an, Weight 24-861bs)
- Small Dogs(Height 25.5-40.7cm, Weight 8-221bs) Mini Dogs(Height under 25cm, Weight under Sibs)