EKE SYSTEM AL900-0100 Ethernet Switches User Manual
- June 4, 2024
- EKE SYSTEM
Table of Contents
AL900-0100 Ethernet Switches
User Manual
AL900-0100 Ethernet Switches
Document #: 10019
Edition: 2022-06-30
| Edition-History
---|---
Ed.0| 2022-02-02, mja| Initial Version
Ed.1| 2022-05-06, mja| SFP+ content extended
Ed.2| 2022-05-16, mja| Shield connection added (photo)
Ed.3| 2022-06-30, mja| Block diagram removed and FCC Statements added
Introduction
- The AL900-0100 is a self-managed network switch. It has 8 Ports (port 1- port 8) with AVB capability). No user configuration is needed.
- 1000BASE-T Ethernet switch, 9 + 1 ports.
- PoE+ support up to 120W in total (ports 5 – port 8). 4x PoE+ (802.3at PoE+). Up to 25W/port.
- SFP rear connector (25000BASE-X) for cascading two switches (over SGMII).
- Nominal 48VDC / 54 VDC power input
I/O ports and connectors
-
Ethernet VLAN Port (not AVB applicable)
-
Port 1 – Port 4 are 1000 BASE-X Ethernet ports which are AVB applicable
-
Port 5 – Port 8 are 1000 BASE-X Ethernet ports that are AVB applicable.
4x PoE+ (802.3at PoE+). Up to 25W / port. 120W in total. -
System LED. The normal State at booting is on.
-
Reset function. A reset will reboot the system. The power will be on.
-
DC LED: This LED is a tricolor LED. The normal state is :
– Green on
– Blue on
This signals that the power is OK.
- Power input connector. DC Input Range 48 VDC, 54 VDC, 3A max.
- Management Ethernet Port without AVB applicable. This 1000 BASE-X Ethernet port is for service only. Not usable for customers.
- SFP 2500 BASE-X port for cascading two AL900-0100 switches. It is an SGMII connection and not hipot-resistant!
*: Shield – connection to PE
Prerequisites
- AL900-0100 switch
- AVB talker and AVB sender, if AVB is needed
- PoE+ powered device if needed
- 48 / 54 VDC power supply
- RJ45 ethernet cables to connect network interfaces with the AL900-0100 switch.
Starting
-
Powering up:
Plug the 48/54VDC power adapter into the DC Jack. Make sure that the power adapter is not turned on. -
Ethernet:
Connect your network devices (PCs or other devices) to the front ethernet ports.
The front ethernet ports 1-8 must be connected to a DHCP server!
Port 0 belongs to VLAN ID 1. -
AVB:
By using the AVB functionality, connect your AVB talker or sender to the front ethernet ports 1-8. -
POE+:
By using powered POE+ devices, connect your PD to ports 5-8. -
Interconnection between 2 AL900-0100 switches:
For interconnection between two AL900-0100 switches, connect an SFP+ cable to the 2.5G Link backport. The port is not hotplugged compatible. It is necessary to finish the interconnection before powering on the boards!
Notice: The 2.5G Link backport is not hipot resistant, because it is an SGMII connection between switch ICs!
FCC Statements
§ 15.21 Information to the user.
Changes or modifications not expressly approved by the party responsible for
compliance could void the user’s authority to operate the equipment.
§ 15.105 Information to the User
Note: This equipment has been tested and found to comply with the limits for a
Class B digital device, pursuant to part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses, and can radiate
radio frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and
on, the user is encouraged to try to correct the interference by one or more
of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and the receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
EKF Elektronik GmbH
E-Mail [email protected]
Internet www.ekf.com