RENPHO R-A030 Luggage Scale User Manual
- June 16, 2024
- Renpho
Table of Contents
RENPHO R-A030 Luggage Scale User Manual
Important Safety Instructions
- Keep the scale out of reach of children to prevent any potential injuries.
- To ensure accuracy, do not use the scale in strong-magnetic fields.
- Do not overload the scale (Max. capacity: 110lb/50kg).
- Wipe the scale with a slightly damp cloth. Do not immerse the scale in water or use chemical or abrasive cleaning agents.
What’s Included
- 1 x RENPHO Luggage Scale
- 2 x AAA Batteries (pre-installed)
Product Overview
Note: Remove the isolation strip from the battery compartment before the first use.
-
Power/Tare/Increase Value Button
a. Short press to power on/tare/ increase the value
b. Long press to power off -
Unit/Set Target Value/Decrease Value Button
a. Short press to switch the unit/ decrease the value
b. Long press to enter the target value setting mode -
LCD Display
“Err”: Overloaded (Max. 110lb/50kg).
Remove the luggage from the scale.
“Lo”: Low battery. Replace the batteries.
“H”: Measurement locked.
“ ”: In target value setting mode -
Triangle Ring
-
Weighing Belt
-
Hook
-
Battery Compartment (Cover)
-
Screw
Converting the Unit
When the scale is on, press “ ” to switch the unit between lb and kg.
Setting the Target Value
The display will turn red as a warning if the luggage weight exceeds the set target value.
- When the scale is on, press and hold “ ” until “ ” is displayed, indicating the scale enters the target value setting mode.
- Press “ ” or “ ” to set your target weight value. Once the desired target value is displayed, press and hold “ ” until “F” appears to save the setting.
Using the Tare Function
- After weighing the container and locking the measurement, press “ ” to reset the scale to zero while keeping the container attached.
- Add the items to the container and the scale will display the weight of only the items without the container.
Weighing
-
Remove the hook from the triangle ring, strap the weighing belt through the luggage handle and secure the hook onto the triangle ring.
-
Press “ ” to turn on the scale and ensure it is set to the desired unit. When the display shows “0.0” or “0.00”, lift the scale gently, ensuring it is horizontal and balanced.
-
Wait until the measurement flashes 3 times and “H” is displayed to lock the final measurement. Use the tare function if needed.
-
To weigh again, remove the luggage and press “ ” to reset the display to zero. To turn off the scale, press and hold “ ”.
Note: The scale will automatically shut off if idle for 2mins.
Replacing the Batteries
- Use a screwdriver (not included) to loosen the screw and remove the battery cover.
- Insert 2 AAA batteries, ensuring correct polarity.
- Align the battery cover with the opening and securely tighten the screw.
Specifications
- Product Name: Luggage Scale
- Model: R-A030
- Unit: lb/kg
- Capacity: 110lb/50kg
- Division: 0.1lb/50g
- Powered by: 2 AAA Batteries (pre-installed)
FCC Regulatory Compliance
This device complies with part 15 of the FCC Rules.
Operation is subject to the following two conditions: (1) This device may not
cause harmful interference, and (2) this device must accept any interference
received, including interference that may cause undesired operation.
Warning: changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a
particular installation.
If this equipment does cause harmful interference to radio or television
reception, which can be determined by turning the equipment off and on, the
user is encouraged to try to correct the interference by one or more of the
following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
ISED Regulatory compliance
This device complies with Industry Canada licence-exempt RSS standard(s).
Operation is subject to the following two conditions: (1) This device may not
cause interference, and (2) This device must accept any interference,
including interference that may cause undesired operation of the device.
Warranty Policy
Your RENPHO product purchase is covered by a one-year limited manufacturer warranty from the date of delivery.
For warranty terms and conditions, please visit: https://renpho.com/pages /warranty-terms-and-conditions
Note: Product registration is not required for the warranty.
If you choose not to register your product, it will not void the product
warranty.
Customer Service
Please feel free to contact us if you have any questions or concerns.
RENPHO Customer Service Team guarantees a quick response and hassle-free
solutions to any issue you may have within business hours.
TEL: +1(844) 417 0149 (US)
Monday-Friday 9:00AM-4:30PM
1800 MY RENPHO (1800 69 7367) (AU)
Monday-Friday 9:00AM-6:00PM (AEST)
Email: support@renpho.com (US&CA)
support-au@renpho.com (AU)
For defective products or the return of items, please contact us with your order number within the specified warranty period. DO NOT dispose of any product parts as they may be required for inspection/repair.
US Importer: JOICOM CORPORATION
14129 The Merge Street, Building 3 Unit A, Eastvale, CA 92880
Manufacturer: Shenzhen Ruiyi Business Technology Co., Ltd.
No. 810-C063, 8th Floor, Xiangbin International Financial Centre, No.18, West
Free Trade Street, China Special Economic Zone, Qianhai Bay, Shenzhen,
Guangdong Province, 518000 China