syvio OL27002546 Bluetooth Wall Light User Manual
- June 16, 2024
- SYVIO
Table of Contents
syvio OL27002546 Bluetooth Wall Light
Please read these instructions thoroughly prior to installation, then store in a safe place for future reference.
For the APP control instruction, please refer to page 11-12.
Scan the brand code to get the instruction videos of how to use
USING STEPS
Step 1. Set the Sensor
Step 2. Install the Light
Step 3. Add the light to AidotApp
Step 4. Set the Modes
We appreciate the trust and confidence you have placed in OREiN through the
purchase of flood light. We strive to continually create quality products
designed to enhance your home. Visit us online to see our full line of
products available for
your home improvement needs.
Thank you for choosing OREiN. ❤
Note: the flood light belongs to the 2nd-class lamp and has obtained the CE, ROHS, and FCC certifications. It is fully compliant in safety rules and safe to use no needing the extra ground wires.
PACKAGE LIST
| |
---|---|---
A: Wire Nuts/Qty.2| B Gasket/Qty. 7
|
C: Machine Screw/Qty. 3| D: Machine Screw/Qty. 3
SENSOR SETTING
Recommended Sensor Setting
- TIME TIME knob to adjust icon position: 30s (common lighting time)
- SENS SENSOR knob to adjust icon position: 40ft (longest triggering distance)
- LUX LUX knob to adjust icon position: 20 Lux
NOTE: LUX has to be at ” ” for 20 Lux in case of lighting in daytime.
Originally Preset Setting for Test
- TIME TIME knob to adjust icon position: 30s (shortest lighting time)
- SENS SENSOR knob to adjust icon position: 40ft (longest triggering distance)
- LUX LUX knob to adjust icon position: 2000 Lux
NOTE: Only for test, please adjust it to the end of “ ” for 201ux after test
INSTALLATION GUIDE
NOTE: Please set the sensor well before installing
TOOLS REQUIRED (not included)
| |
---|---|---
Flathead Screwdriver| Screwdriver| Silicone Sealant
| |
Step Ladder| Eye Protection| Pliers
Note:
- At an ambient temperature of 77 degrees fahrenheit, Rh 30%-80% the detection distance is at max. (up to 40ft). As the temperature increases or decreases, the detection distance will be affected.
- To reduce possible nuisances, do not mount the fixture near a heat source like an air conditioner, vent or furnace exhaust, or in a direction facing any reflective object or other nearby light source.
- No any reflective object can be allowed within 1.5m radius of the sensor head, otherwise, it will cause flashing lights.
SAFETY INFORMATION
Please read and understand this entire manual before attempting to assemble,
operate or install the product.
PRODUCT MUST BE INSTALLED BY A QUALIFIED ELECTRICIAN !
WARNING
Shut off power at the circuit breaker or fuse panel before removing the old
fixture or installing the new one.
LED electronics can be damaged by electrostatic discharge (ESD) shock. Before
installation, discharge yourself by touching a grounded bare metal surface to
remove this hazard. To avoid damage, do not remove the clear lens over the LED
module.
IMPORTANT SAFETY INSTRUCTIONS
-
Turn power OFF before installing or servicing.
-
Do NOT touch or install fixture while in contact with standing water.
-
Do NOT remove the protective LED lens.
-
Do NOT look directly at lighted LEDs for any length of time.
-
Do NOT leave bare wires exposed outside the wall canopy enclosure.
-
Electrical requirements: 100-240V, 50/60Hz
-
Suitable for wall or eave mounting onto recessed or round surface mounted electrical boxes rated for wet location.
Not suitable for ground mount electrical boxes. -
Do NOT allow the sensor head to touch the LED head housing.
Maintain at least 1 in. spacing between the LED heads and the sensor head. -
For proper operation and protection against water damage, the motion sensor adjustment controls MUST be facing downward.
-
Do NOT mount below 5 ft.
PREPARATION
Before beginning installation of product, make sure all parts are present.
Compare parts with parts list.
If any part is missing or damaged, do not attempt to install the product.
Tools Required for Assembly (not included):
Phillips Screwdriver, Flat-head Screwdriver, Step Ladder, Pliers, Silicone
Sealant, Eye Protection.
ASSEMBLY INSTRUCTIONS
CAUTION: Product must be installed by a qualified electrician!
-
Turn off power to work area at main circuit breaker or fuse box.
CAUTION: Do not rely on wall switch to turn off power. -
Pass the wire through the washer (B). Make sure the holes match each other.
-
Wiring the light and junction box through the mounting bracket.
a. Connect the white wire to the white wire by twisting Wire Nut (A).
b. Connect the black wire to the black wire by twisting Wire Nut (A). -
Make sure the cable connections are secure. Carefully align the cables in the junction box. Mount the light to the junction box and secure with the NUTS (D). DO NOT over tighten compound or silicone glue.
Once all connections are complete and the silicone is dry, you can turn on the power to the light at the main junction box or breaker panel. -
Installation is now complete.
Turn on power at circuit breaker and flip wall switch to ON position.
Wall switch must remain in the ON position for the motion detector to work properly (include daytime).
ADJUST THE LIGHT ARMS
Aim sensor head toward desired detection area and make sure sensor head is positioned with controls facing toward the ground You can adjust the sensor head up and down, left to right for desired coverage area.
Please aim the sensor head toward your desired detecting area.
RECOMMENDED INSTALL HEIGHT
- 5.9-8.2 feet above the ground.
- At such a height, the fixture will provide a detection distance of up to 40 feet at 77 degrees fahrenheit.
The sensor will be more sensitive to motion across than motion towards it
directly.
MODES DESCRIPTION
- Long press the button for more thar 2S to turn on/off the a light, and the light has a memory function.
- Click the button (<0.5S) to switch the color temperature cyclically, the color temperature mode is 2700K/ 4000K/ 6500K-cycle.
- Double-click the button (within 1 S) to cycle through the following three modes.
Double Click the Button to Switch Modes
| |
---|---|---
Motion Mode| Dim Light Mode| Light Mode
The light will turn on at full brightness when motion is detected at night.
Deactivates during the daylight hours.| The light will have a brightness of
20% when no one is around at night, and 100% brightness when motion is
detected.| The light can be manually turned on and off, and will be at 100%
brightness.
Note:
- the motion mode and dim light mode are combined into 1 mode to set in the app.
- The mode can be set according to personal preferences on the AiDot app.
TROUBLES SHOOTING
PROBLEM | PROBLEM CAUSE | CORRECTIVE ACTION |
---|---|---|
Light does not come on at night when motion is detected |
- No power is being delivered to the light.
- Another light source is causing the security light to think it is daylight
- Wiring inside electrical box came Loose.
|
- Check that circuit breaker and/or wall switch power is on.
- Turn off surrounding lights or re-aim the sensor head.
- After turn in a power off to the light reconnect any loose wiring.
Security light comes on during the day.| Sensor is in a shaded area and fooled into thinking it is nighttime.|
- Shine a flashlight onto the light sensor.
- Relocate security light to where allows enough light enter the sensor during daytime.
The Light flashes.| There is lighting, welding. Mobile sources or other such
unstable light.| Avoid to irradiate by such light source.
The light turn on in daytime.|
- Lux knob setting is wrong.
- Surrounding environment is too dark.
|
-
Adjust the Lux knob to “ “.
-
Check the surround environment.
PRODUCT SPECIFICATION
SPECIFICATIONS | SPECIFICATIONS |
---|---|
Wattage: 24W | Ambient illumination: 20-2000Lux |
(adjustable)
Lumens: 2800LM| Distance Lighting: 6.5ft-40ft (adjustable)
Color Temperature: 2700K~6500K| Lighting Time: 30S to 8min (adjustable)
Voltage: AC 100-240V, 50/60HZ| Installation Height 5.9ft-8.2ft
Sensor Adjustable angle: Vertical Max 180° /Horizontal Max 350°| Sensing
Angle: 180°
APP CONNECTION
For the App connection guide, please refer to the last part of page 11-12.
CONNECT THE APP
-
Get the Ai Dot APP from App Store or Google Play.
|
---|---
| -
Create an account and sign in.
-
Press ‘+’ button to add device.
-
Follow the instructions on App.
-
Add the device
-
Choose the device what you find in ‘Nearby’ (PS: You must open the Bluetooth and Location Services. If you still can not fine the device in ‘Nearby’, Try to reset the device: Long press the button for more than 1 OS to enter flash mode.)
-
Waiting to connect
-
Added Successfully
FCC WARNING
This device complies with part 15 of the FCC Rules.
Operation is subject to the following two conditions:
-
this device may not cause harmful interference, and
-
this device must accept any interference received, including interference that may cause undesired operation.
Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment .
NOTE: This equipment has been tested and found to comply with t he limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by tuning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
To maintain compliance with Feck’s RF Exposure guidelines, This equipment should be installed and operated with minimum 20 cm distance between the radiator and your body: Use only the supplied antenna.
CUSTOMER SUPPORT
Scan the brand code to get the instruction videos of how to use
Points de collecte sur www.quefairedemesdechets.fr
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>