SYVIO SA3300296 Cool Mist Humidifier Instruction Manual

June 15, 2024
SYVIO

SYVIO SA3300296 Cool Mist Humidifier Instruction Manual
SYVIO SA3300296 Cool Mist Humidifier

NAMES OF PARTS

Product Overview

FUNCTION CHARACTERISTICS

  • Power Button:
    On the stand-by state:
    1st Press: Turn on the medium mist with two mist icon indicators light on, blue LED light on.
    2nd Press: Turn off the humidifier.
    Note: When waterless, the display will shows “E2” error code and the waterless icon light will flash with buzzer warning 3 times (around
    7S), and then will power off; If you press again, it will repeat the flash and the warning again.

  • Mist Button:
    On medium mist state:
    1st Press: Turn on the high mist with three mist icon indicators light on.
    2nd Press: Turn on the low mist with one mist icon indicators light on.
    3rd Press: Turn on the medium mist with two mist icon indicators light on.
    Cycle control.

  • Sleeping mode:
    Long press the mist button for 3 seconds to enter the sleeping mode with sleeping mode icon light on, the lighting of the water tank and other icon of the display will turn off, mist volume will turns to low mist mode; When waterless, unit will auto turn off without buzzer beeps. Short press any button to exit the sleeping mode, will keep the mist volume and light mode that setting before.

  • Timer Button:
    On working state:
    1st Press: Display will shows the current setting timer, if no timer setting will shows “–”H.
    2nd Press: Reset the timer, display shows “02” with timer icon “H” light on, and the unit will power off after 2H
    3rd Press: Display shows “04” with timer icon “H” light on, and the unit will power off after 4H.
    4th Press: Display shows “08” with timer icon “H” light on, and the unit will power off after 8H.
    5th Press: Display shows “–” with timer icon “H” light on, and no timer setting.
    Cycle control.

  • Humidity Button:
    On working state:
    1st Press: Display will shows the current setting humidity, if no humidity setting will shows “–”%.
    2nd Press: Setting the 40% humidity, display shows “40” with humidity icon “%” light on.
    3rd Press: Setting the 50% humidity, display shows “50” with humidity icon “%” light on.
    4th Press: Setting the 60% humidity, display shows “60” with humidity icon “%” light on.
    5th Press: Setting the 70% humidity, display shows “70” with humidity icon “%” light on.
    6th Press: Setting the 80% humidity, display shows “80” with humidity icon “%” light on.
    7th Press: No humidity setting, display shows “–” with humidity icon “%” light on.
    Cycle control.

Note:

  1. After finishing the humidity setting, the display will show thermal-time humidity after finishing the setting.
  2. When the real-time humidity lower than the setting humidity, humidifier will work with the current setting mist mode; When the real-timer humidity higher than the setting humidity, humidifier will stop misting.
  • Waterless protection function: When lacking water, the display will shows “E2” and the waterless icon light will flash with buzzer warning 3 times (around 7S), and then will power off; If you press again, it will repeat the flash and the warning again.
  • Touch button sound: Each press will comes with one buzzer beep.
  • Stand-by stage: The buzzer beeps when power on.
  • Humidity display: Humidity display: Displays the humidity and the humidity icon. (When the humidity ≥85%RH, the display shows H%RH; When the humidity ≤30%RH, the display shows L%RH), if any poor contact of the humidity detector, the display will shows“E3” error code.
  • Intelligent constant humidity mode: Automatically adjust the mist spray state according to the humidity setting value.
  • Sleeping Mode: Turn off the lighting of the water tank, all the icon of the display will turn off, mist volume will turns to low mist mode; When waterless, unit will auto turn off without buzzer beeps.

Power: 25W
Voltage: 110V~
Mist Volume: 200±40 ml/h
Working Time: 24H(low mist),12H(high mist)
Capacity: 2.8L
Timer: 2H/4H/8H
Size: 195×182×263mm

INSTRUCTIONS FOR USE

Place unit on a flat, water-resistant surface as moisture may cause damage to carpet, finished floors, furniture, or walls.

  1. Remove the Top Cover from the Water Tank.
  2. Fill the Water Tank with tap water up to the Max Water Level Line. Do not overfill. Add approximately 10 drops of essential oil per 1 liter of water into the Water Tank.
  3. Replace Top Cover onto the Water Tank.
  4. Plug the Power Cord into an electrical wall outlet. It will take a few minutes for the essential oil to blend with the water before fragrance begins diffusing.

CARE & MAINTENANCE

Do not add hot water, only suitable for cold water Please use the original power cord Always unplug the power cord from electrical outlet before filling. Essential oil should not come in contact with the exterior surface of unit. Do not submerge unit into water to avoid risk of exterior surface of unit. Do not submerge unit into water to avoid risk of electric shock. Do not put fingers, hands, or any object into the unit while operating. Do not attempt to adjust or repair the unit. Do not touch the water while unit is operating. Do not fill water through the Mist Outlet or the Air Outlet. Do not place the unit near heat sources or direct sunlight. Use two hands when moving your humidifier Please follow the instruction manual to operate the unit.

Easy to Clean:

Pour the water out of the tank, be careful do not pour water out from the air outlet side. The ceramic disc should not come in contact with any hard or sharp objects. To remove possible buildup, rinse with a white vinegar and water solution. Dry thoroughly with a soft cloth. Do not use strong cleaning agents.

Note: Recommend to clean the humidifier once a week

TROUBLE SHOOTING

Problem Possible Factors Solution
Will not turn on or turn off? Not enough water in the tank Please add enough

water to the tank, not exceeding the 2.8L MAX water line.
The power cord connects not properly| Please disconnect the cord, check the cables and reconnect carefully.
Will not put out mist?| Not enough water or too much in the tank| Please add enough water to the tank, not exceeding the 2.8L MAX water line.
The “Mist Outlet” has dirt| Just clean the “mist outlet” put it in a cool place and wait for it to dry naturally, then it can be used normally.
The “Air Intake” port under the base has dirt| Clean the “air intake” with a dry brush

Get Help Fast
“Thanks for purchasing the SYVIO product!
If there is any problem, please contact us for a replacement or refund.
Also, register your order id for an EXTRA 12-months warranty!
Support Email: support@mysyvio.com”

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals