Hotpoint H2F HL626 X UK Dishwasher User Guide

Hotpoint H2F HL626 X UK Dishwasher

Product Information

Specifications

• Upper rack with foldable flaps
• Upper rack height adjuster
• Upper spray arm
• Lower rack
• Cutlery basket
• Lower spray arm
• Filter Assembly
• Salt reservoir
• Detergent and Rinse Aid dispensers
• Rating plate
• Control panel with On-Off/Reset button, Program selection button, Half Load button, Rinse Aid refill indicator light, Salt refill indicator light, Program indicator lights, Delay indicator light, Delay button, Tablet (Tab) button, Start/Pause button, Drain out button

Product Usage Instructions

First-Time Use – Salt, Rinse Aid, and Detergent

Advice regarding the first time use:
After installation, remove the stoppers from the racks and the retaining elastic elements from the upper rack.

Filling the Salt Reservoir:
The salt reservoir is located in the lower part of the dishwasher. Follow the steps below:

1. Remove the lower rack and unscrew the reservoir cap (anticlockwise).
2. If it is the first time, fill the salt reservoir with water.
3. Position the funnel and fill the salt reservoir right up to its edge (approximately 1 kg). Some water leakage is normal.
4. Remove the funnel and wipe any salt residue away from the opening.
5. Ensure the cap is screwed on tightly to prevent detergent from entering the container during the wash program.
6. It is mandatory to complete this procedure before the beginning of the washing cycle whenever you need to add salt to avoid corrosion.

Setting the Water Hardness:
To allow the water softener to work properly, set the water hardness based on the actual water hardness in your house. Follow the table below:

After completing the water hardness setting, run a program without loading. Use only salt specifically designed for dishwashers. The SALT REFILL indicator light will switch off after pouring salt into the machine. Failure to fill the salt container may result in damage to the water softener and heating element due to limescale accumulation. It is recommended to use salt with any type of dishwasher detergent.

FAQ

• Q: How can I register my appliance?
  A: To receive complete assistance, please register your appliance on our website www.hotpoint.eu/register.

• Q: Where can I find the Safety Instructions and User Manual?
  A: You can download the Safety Instructions and User Manual from our website docs.hotpoint.eu. Follow the instructions provided on the back of this booklet.

• Q: How do I turn on/off the appliance?
  A: Use the On-Off/Reset button with the indicator light on the control panel to turn the appliance on or off.

• Q: How do I select a program?
  A: Use the Program selection button with the indicator light on the control panel to choose a program.

• Q: What does the Half Load button do?
  A: The Half Load button with the indicator light on the control panel allows you to wash a smaller load, saving water and energy.

• Q: How do I refill Rinse Aid?
  A: Refill the Rinse Aid by following the instructions in the User Manual and monitor the Rinse Aid refill indicator light on the control panel.

• Q: How do I refill Salt?
  A: Refill Salt by following the instructions in the User Manual and monitor the Salt refill indicator light on the control panel.

• Q: How do I start or pause a program?
  A: Use the Start/Pause button with the indicator light on the control panel to start or pause a program.

• Q: How do I drain out the water?
  A: Use the Drain out button on the control panel to drain out the water.

THANK YOU FOR BUYING A HOTPOINT PRODUCT.

• In order to receive a more complete assistance, please register your appliance on: www.hotpoint.eu/register.
• You can download the Safety Instructions and the User Manual, by visiting our website docs.hotpoint.eu and following the Instructions on the back of this booklet.

Before using the appliance carefully read Safety Instructions guide.

PRODUCT DESCRIPTION

APPLIANCE

1. Upper rack
2. Foldable flaps
3. Upper rack height adjuster
4. Upper spray arm
5. Lower rack
6. Cutlery basket
7. Lower spray arm
8. Filter Assembly
9. Salt reservoir
10. Detergent and Rinse Aid dispensers
11. Rating plate
12. Control panel

CONTROL PANEL

1. On-Off/Reset button with indicator light
2. Program selection button with indicator light
3. Half Load button with indicator light
4. Rinse Aid refill indicator light
5. Salt refill indicator light
6. Program indicator lights
7. Delay indicator light
8. Delay button with indicator light
9. Tablet (Tab) button with indicator light
10. Start/Pause button with indicator light/Drain out

FIRST TIME USE

SALT, RINSE AID AND DETERGENT

ADVICE REGARDING THE FIRST-TIME USE
After installation, remove the stoppers from the racks and the retaining elastic elements from the upper rack.

FILLING THE SALT RESERVOIR
The use of salt prevents the formation of LIMESCALE on the dishes and on the machine’s functional components.

• THE SALT RESERVOIR must NEVER BE EMPTY.
• It is important to set the water hardness.

The salt reservoir is located in the lower part of the dishwasher (see PRODUCT DESCRIPTION) and must be filled when the SALT REFILL indicator light in the control panel is lit.

1. Remove the lower rack and unscrew the reservoir cap (anticlockwise).
2. Only the first time you do this: fill the salt reservoir with water.
3. Position the funnel (see figure) and fill the salt reservoir right up to its edge (approximately 1 kg); it is not unusual for a little water to leak out.
4. Remove the funnel and wipe any salt residue away from the opening.

Make sure the cap is screwed on tightly so that no detergent can get into the container during the wash program (this could damage the water softener beyond repair). Whenever you need to add salt, it is mandatory to complete the procedure before the beginning of the washing cycle to avoid corrosion.

SETTING THE WATER HARDNESS
To allow the water softener to work in a perfect way, it is essential that the water hardness setting is based on the actual water hardness in your house. This information can be obtained from your local water supplier.

The factory sets the default value for the water hardness.

• Switch on the appliance by pressing the ON/OFF button.
• Switch off the appliance by pressing the ON/OFF button.
• Hold down the button START/Pause for 5 seconds, until you hear a beep.
• Switch on the appliance by pressing the ON/OFF button.
• The program indicator light of the current set level flashes.
• Press button P to select the desired hardness level (see WATER HARDNESS TABLE).

Water Hardness Table

Level| °dH

German degrees

| °fH

French degrees

| °Clark

English degrees

1| Soft| 0 – 6| 0 – 10| 0 – 7
2| Medium| 7 – 11| 11 – 20| 8 – 14
3| Average| 12 – 16| 21 – 29| 15 – 20
4| Hard| 17 – 34| 30 – 60| 21 – 42
5| Very hard| 35 – 50| 61 – 90| 43 – 62

• Switch off the appliance by pressing the ON/OFF button.

The setting is complete!

• As soon as this procedure is complete, run a program without loading.
• Only use salt that has been specifically designed for dishwashers. After the salt has been poured into the machine, the SALT REFILL indicator light switches off.
• If the salt container is not filled, the water softener and the heating element may be damaged as a result of limescale accumulation.
• Using Salt is recommended with any type of dishwasher detergent.

FILLING THE RINSE AID DISPENSER
Rinse aid makes dish DRYING easier. The rinse aid dispenser A should be filled when the RINSE AID REFILL indicator light in the control panel is lit.

1. Open the dispenser B by pressing and pulling up the tab on the lid.
2. Pour in the rinse aid (max.110 ml), making sure it does not overflow from the dispenser. If this happens, clean the spill immediately with a dry cloth.
3. Press the lid down until you hear a click to close it.

NEVER pour the rinse aid directly into the appliance tub.

ADJUSTING THE DOSAGE OF RINSE AID
If you are not completely satisfied with the drying results, you can adjust the quantity of rinse aid used.

• Switch the dishwasher on using the ON/OFF button.
• Switch it off using the ON/OFF button.
• Press the button START/Pause three times – a beep will be heard.
• Switch it on using the ON/OFF button.
• The program indicator light of the current set level flashes.
• Press button P to select the level of rinse aid quantity to be supplied.
• Switch it off using the ON/OFF button

The setting is complete!
If the rinse aid level is set to 1 (ECO), no rinse aid will be supplied. The LOW RINSE AID indicator light will not be lit if you run out of rinse aid. A maximum of 5 levels can be set according to the dishwasher model. The factory setting is specific to the model, please follow the instructions above to check this for your machine.

• If you see bluish streaks on the dishes, set a low number (2-3).
• If there are drops of water or limescale marks on the dishes, set a mid-range number (4-5).

FILLING THE DETERGENT DISPENSER
To open the detergent dispenser use the opening device C. Introduce the detergent into the dry dispenser D only. Place the amount of detergent for pre-washing directly inside the tub.

1. When measuring out the detergent refer to the mentioned earlier information to add the proper quantity. Inside the dispenser D, there are indications to help the detergent dosing.
2. Remove detergent residues from the edges of the dispenser and close the cover until it clicks.
3. Close the lid of the detergent dispenser by pulling it up until the closing device is secured in place.

The detergent dispenser automatically opens up at the right time according to the program. If all-in-one detergents are used, we recommend using the TABLET button, because it adjusts the program so that the best washing and drying results are always achieved. Usage of detergent not designed for dishwashers may cause malfunction or damage to the appliance.

PROGRAMS TABLE

ECO program data is measured under laboratory conditions according to European Standard EN 60436:2020.

Note for Test Laboratories:

• For information on comparative EN testing conditions, please send an email to the following address: dw_test_support@whirlpool.com
• Pre-treatment of the dishes is not needed before any of the programs.
• Not all options can be used simultaneously.
• Values given for programs other than the program Eco are indicative only. The actual time may vary depending on many factors such as temperature and pressure of the incoming water, room temperature, amount of detergent, quantity and type of load, load balancing, additional selected options and sensor calibration. The sensor calibration can increase program duration up to 20 min.

PROGRAMS DESCRIPTION

Instructions on wash cycle selection.

1. ECO
   Eco programme is suitable for cleaning normally soiled tableware, for this use, it is the most efficient programme in terms of its combined energy and water consumption, and it is used to assess compliance with the EU Ecodesign legislation.

2. INTENSIVE
   Program recommended for heavily soiled crockery, especially suitable for pans and saucepans (not to be used for delicate items).

3. MIXED
   Mixed soil. For normally soiled dishes with dried food residues.

4. RAPID 30’
   Program to be used for a half load of lightly soiled dishes with no dried food residues. Does not include the drying phase.

5. SOAK
   Use to refresh crockery planned to be washed later. No detergent is to be used with this program.

Notes:
Please note that cycle Rapid 30’ is dedicated to lightly soiled dishes.

OPTIONS AND FUNCTIONS

OPTIONS can be selected directly by pressing the corresponding button (see CONTROL PANEL).

If an option is not compatible with the selected program see PROGRAMS TABLE, the corresponding LED flashes rapidly 3 times and beeps will sound. The option will not be enabled.

• HALF LOAD
  If there are not many dishes to be washed, a half-load cycle may be used to save water, electricity and detergent. Select the program and press the HALF LOAD button: the indicator light will light up. Press the HALF LOAD button to deselect this option.
  Remember to halve the amount of detergent.

• DELAY
  It is possible to delay the start time of the program by 2, 4 or 8 hours:

1. After selecting the desired program and any other options, press the DELAY button. The indicator light will go on.
2. Select the desired delay time by pressing the DELAY button repeatedly. The 2 hours, 4 hours and 8 hours indicator lights will go on in succession. If the DELAY button is pressed again, the option is deselected and the indicator light goes off.
3. After the selection process, the countdown will begin if the START/PAUSE button is pressed. The selected delay-period indicator light is on and the Start/Pause button lights up (fixed light).
4. Once this time has elapsed, the DELAY indicator light goes off and the program begins.  

The DELAY function cannot be set once a program has started.

• TABLET (Tab)
  • This setting allows you to optimize the performance of the program according to the type of detergent used.
  • Press the TABLET button (the indicator light will light up) if you use combined detergents in tablet form (rinse aid, salt and detergent in 1 dose).
  • If you use powder or liquid detergent, this option should be off.
• DRAIN OUT
  • To stop and cancel the active cycle, the DRAIN OUT function can be used.
  • A long press of the START/PAUSE button will activate the DRAIN OUT function. The active program will be stopped and the water in the dishwasher will be drained out.

LOADING THE RACKS

UPPER RACK
Load delicate and light dishes: glasses, cups, saucers, and low salad bowls.

ADJUSTING THE HEIGHT OF THE UPPER RACK
The height of the upper basket can be adjusted: a high position to place bulky crockery in the lower basket and a low position to make the most of the tip-up compartments by creating more space upwards. The upper rack is equipped with an Upper Rack height adjuster (see figure), without pressing the levers, lift it up by simply holding the rack sides, as soon as the rack is stable in its upper position. To restore to the lower position, press the levers (A) at the sides of the rack and move the basket downwards. We strongly recommend that you do not adjust the height of the rack when it is loaded. NEVER raise or lower the basket on one side only.

FOLDABLE FLAPS WITH ADJUSTABLE POSITION
The side foldable flaps can be folded or folded to optimize the arrangement of crockery inside the rack. Wine glasses can be placed safely in the foldable flaps by inserting the stem of each glass into the corresponding slots.

Depending on the model:

• to unfold the flaps there is needed to slide it up and rotate or release it from the snaps and pull it down.
• to fold the flaps there is needed to rotate it and slide flaps down or pull it up and attach flaps to the snaps.

LOWER RACK
For pots, lids, plates, salad bowls, cutlery etc. Large plates and lids should ideally be placed at the sides to avoid interferences with the spray arm.

CUTLERY BASKET
The basket is equipped with top grilles for improved cutlery arrangement. The cutlery basket should be positioned only at the front of the lower rack.

Knives and other utensils with sharp edges must be placed in the cutlery basket with the points facing downwards or they must be positioned horizontally in the tip-up compartments on the upper rack.

DAILY USE

1. CHECK WATER CONNECTION
   Check that the dishwasher is connected to the water supply and that the tap is open.

2. SWITCH ON THE DISHWASHER
   Press the ON/OFF button.

3. LOAD THE RACKS (see LOADING THE RACKS)

4. FILLING THE DETERGENT DISPENSER

5. CHOOSE THE PROGRAM AND CUSTOMISE THE CYCLE

   • Select the most appropriate program by the type of crockery and its soiling level (see PROGRAMS DESCRIPTION) by pressing the P button.
   • Select the desired options (see OPTIONS AND FUNCTIONS).

6. START
   Start the wash cycle by pressing the START/PAUSE button. When the program starts you hear a beep.

7. END OF WASH CYCLE

   • The end of the wash cycle is indicated by beeps and by the flashing of the wash cycle indicator on the panel. Open the door and switch off the appliance by pressing the ON/OFF button.
   • Wait for a few minutes before removing the crockery – to avoid burns. Unload the racks, beginning with the lower one.

The machine will switch off automatically during certain extended periods of inactivity, to minimise electricity consumption. If the crockery is only lightly soiled or if it has been rinsed with water before being placed in the dishwasher, reduce the amount of detergent used accordingly.

• MODIFYING A RUNNING PROGRAM
  If a wrong program was selected, it is possible to change it, provided that it has only just begun: press and hold the ON/OFF button, and the machine will switch off. Switch the machine back on using the ON/OFF button and select the new wash cycle and any desired options; start the cycle by pressing the START/PAUSE button.

• ADDING EXTRA CROCKERY
  Without switching off the machine, open the door (beware of HOT steam!) and place the crockery inside the dishwasher. Close the door and press the START/PAUSE button the cycle will begin from the point at which it was interrupted.

• ACCIDENTAL INTERRUPTIONS
  If the door is opened during the wash cycle, or if there is a power cut, the cycle stops. Once the door has been closed or the electricity supply is restored, to start again the cycle from where it was interrupted, press the START/PAUSE button.

ADVICE AND TIPS

TIPS

• Before loading the baskets, remove all food residues from the crockery and empty the glasses. You do not need to rinse beforehand under running water.
• Arrange the crockery so that it is held in place firmly and does not tip over; and arrange the containers with the openings facing downwards and the concave/convex parts placed obliquely, thus allowing the water to reach every surface and flow freely.
• Warning: lids, handles, trays and frying pans do not prevent the sprayer arms from rotating.
• Place any small items in the cutlery basket.
• Very soiled dishes and pans should be placed in the lower basket because in this sector the water sprays are stronger and allow a higher washing performance.
• After loading the appliance, make sure that the sprayer arms can rotate freely.

UNSUITABLE CROCKERY

• Wooden crockery and cutlery.
• Delicate decorated glasses, artistic handicrafts and antique crockery. Their decorations are not resistant.
• Parts in synthetic material that do not withstand high temperatures.
• Copper and tin crockery.
• Crockery soiled with ash, wax, lubricating grease or ink.

The colours of glass decorations and aluminium/silver pieces can change and fade during the washing process. Some types of glass (e.g. crystal objects) can become opaque after some wash cycles too.

DAMAGE TO GLASS AND CROCKERY

• Only use glasses and porcelain guaranteed by the manufacturer as dishwasher safe.
• Use a delicate detergent suitable for crockery
• Collect glasses and cutlery from the dishwasher as soon as the wash cycle is over.

TIPS ON ENERGY SAVING

• When the household dishwasher is used according to the manufacturer’s instructions, washing tableware in a dishwasher usually consumes less energy and water than hand dishwashing.
• To maximize dishwasher efficiency it is recommended to initiate the wash cycle once the dishwasher is fully loaded. Loading the household dishwasher up to the capacity indicated by the man-ufacturer will contribute to energy and water savings. Information on the correct loading of tableware can be found in the Loading chapter. In case of partial loading, it is recommended to use dedicated wash options if available (Half load/ Zone Wash, Multi-Zone), filling up only selected racks. Incorrect loading or overloading the dishwasher may increase resource usage (such as water, energy and time, as well as increase noise level), reducing cleaning and drying performance.
• Manual pre-rinsing of tableware items leads to increased water and energy consumption and is not recommended.

HYGIENE
To avoid odour and sediment which can be accumulated in the dishwasher please run a high-temperature program at least once a month. Use a teaspoon of detergent and run it without loading to clean your appliance.

CARE AND MAINTENANCE

CLEANING THE FILTER ASSEMBLY

• Regularly clean the filter assembly so that the filters do not clog and that the waste water flows away correctly.
• Using a dishwasher with clogged filters or foreign objects inside the filtration system or sprayarms may cause unit malfunction resulting in loss of performance, noisy work or higher resource usage.
• The filter assembly consists of three filters which remove food residues from the washing water and then recirculate the water.

The dishwasher must not be used without filters or if the filter is loose.
At least once per month or after every 30 cycles, check the filter assembly and if necessary clean it thoroughly under running water, using a non–metallic brush and following the instructions below:

1. Turn the cylindrical filter A in an anti-clockwise direction and pull it out (Fig 1).
2. Remove the cup filter B by exerting a slight pressure on the side flaps (Fig 2).
3. Slide out the stainless-steel plate filter C (Fig 3).
4. In case you find foreign objects (such as broken glass, porcelain, bones, fruit seeds etc.) please remove them carefully.
5. Inspect the trap and remove any food residues. NEVER REMOVE the wash-cycle pump protection (black detail) (Fig 4).

After cleaning the filters, replace the filter assembly and fix it in position correctly; this is essential for maintaining the efficient operation of the dishwasher.

CLEANING THE WATER INLET HOSE
If the water hoses are new or have not been used for an extended period of time, let the water run to make sure it is clear and free of impurities before performing the necessary connections. If this precaution is not taken, the water inlet could become blocked and da-mage the dishwasher.

CLEANING THE SPRAY ARMS
On occasions, food residue may become encrusted onto the spray arms and block the holes used to spray the water. It is therefore recommended that you check the arms from time to time and clean them with a small non-metallic brush.

To remove the upper spray arm, turn the plastic locking ring in a clockwise direction. The upper spray arm should be replaced so that the side with the greater number of holes is facing upwards.

The lower spray arm may be removed by pulling it upwards.

WATER SOFTENING SYSTEM

• Water softener automatically reduces water hardness, consequently preventing scale buildup on the heater, contributing also to better cleaning efficiency.
• This system regenerates itself with salt, therefore it is required to refill salt containers when empty.
• The frequency of regeneration depends on the water hardness level setting – regeneration takes place once per 5 Eco cycles with the water hardness level set to 3.
• The regeneration process starts in the final rinse and finishes in the drying phase before the cycle ends.
  • Single regeneration consumes: ~3.5L of water;
  • Takes up to 5 additional minutes for the cycle;
  • Consumes below 0.005kWh of energy.

TROUBLESHOOTING

In case your dishwasher doesn’t work properly, check if the problem can be solved by going through the following list. For other errors or issues please contact authorized After-sales Service whose contact details can be found in the warranty booklet. Spare parts will be available for a period of either up to 7 or up to 10 years, according to the specific Regulation requirements.

salt (for more information – see page 2). Adjust water hardness.
The rinse aid indicator is lit| The rinse aid dispenser is empty (after refill the rinse aid indicator may remain lit for several wash cycles).| Refill dispenser with rinse aid (for more information – see page 2).
The dishwasher won’t start or does not respond to commands.| The appliance has not been plugged in properly.| Insert the plug into the socket.
Power outage.| For safety reasons, the dishwasher will not restart automatically when power returns. Press the START/Pause button to resume the cycle.
The dishwasher door is not closed.| Vigorously push the door until you hear the “click”.
The cycle is interrupted by the door opening for > 4 sec.| Close the door and press the START/Pause button.
It does not respond to commands.| Switch off the appliance by pressing the ON/OFF button, switch it back on after approximately one minute and restart the program. If the problem persists, unplug the appliance for 1 minute, then plug it back in.
The dishwasher won’t drain.| The wash cycle has not finished yet.| Wait until the wash cycle finishes.
The drain hose is bent.| Check that the drain hose is not bent (see INSTALATION INSTRUCTION).
The sink drain pipe is blocked.| Clean the sink drain pipe.
The filter is clogged up with food residues.| Clean the filter (see CLEANING THE FILTER ASSEMBLY).
The dishwasher makes excessive noise.| The dishes are rattling against each other.| Position the crockery correctly (see LOADING THE RACKS).

An excessive amount of foam has been produced.

| The detergent has not been measured out correctly or it is not suitable for use in dishwashers (see FILLING THE DETERGENT DISPENSER). Restart the dishwasher by pressing the DRAIN button (see OPTIONS AND FUNCTIONS) and run the new program without detergent.
The dishes are not clean.| The crockery has not been arranged properly.| Arrange the crockery correctly (see LOADING THE RACKS).
The spray arms cannot rotate freely, being hindered by the dishes.| Arrange the crockery correctly (see LOADING THE RACKS).
The wash cycle is too gentle.| Select an appropriate wash cycle (see PROGRAMS TABLE).
An excessive amount of foam has been produced.| The detergent has not been measured out correctly or it is not suitable for use in dishwashers (see FILLING THE DETERGENT DISPENSER).
The cap on the rinse aid compartment has not been shut correctly.| Make sure the cap of the rinse aid dispenser is closed.
The filter is soiled or clogged.| Clean the filter assembly (see CARE AND MAINTENANCE).
There is no salt.| Fill the salt reservoir (see FILLING THE SALT RESERVOIR).
The dishwasher does not fill the water.

All LEDs are blinking rapidly

| No water in the water supply or the tap is closed.| Make sure there is water in the water supply or the tap running.
The inlet hose is bent.| Make sure the inlet hose is not bent (see INSTALLATION) reprogram the dishwasher and reboot.
The sieve in the water inlet hose is clogged; it is necessary to clean it.| After having carried out the verification and cleaning, turn off and turn on the dishwasher and restart a new program.
The dishwasher finishes the cycle prematurely.| Drain hose positioned too low or siphoning into the home sewage system.| Check if the end of the drain hose is placed at the correct height (see INSTALLATION). Check for siphoning into the home sewage system, and install an air admittance valve if necessary.
Air in water supply.| Check the water supply for leaks or other issues letting air inside.

Policies, standard documentation, ordering of spare parts and additional product information can be found by:

• Using the QR code and visiting our website: docs.hotpoint.eu
• Visiting our website: parts-selfservice.whirlpool.com
• Alternatively, contact our After-sales Service (See phone number in the warranty booklet). When contacting our After-sales Service, please state the codes provided on your product’s identification plate.

The model information can be retrieved using the QR code reported in the energy label. The label also includes the model identifier that can be used to consult the portal of the registry at https://eprel.ec.europa.eu.

References

• Whirlpool Docs
• Hotpoint: Purchase Quality Home & Kitchen Appliances Online | HotPoint EU

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>