legrand WNRLX4 Radiant Wireless Dimmer Switch Instruction Manual

legrand WNRLX4 Radiant Wireless Dimmer Switch

Product Information

• Specifications
  • Model: WZ3RL64
  • Type: Wireless AC Smart Dimmer with Zigbee

Product Usage Instructions

• Before You Start
  • Turn off the power to the device at the circuit breaker. Ensure power is off to all devices in the electrical box.
  • Remove existing device (if applicable).
• Check for the following wires:
  • HOT or LINE: Receives power from the circuit box. Referred to as hot for this guide. Do not touch or let hot wire contact other wires.
  • NEUTRAL: Creates a path to return current to the power source when the device is off. Required for your dimmer installation.
  • GROUND: Provides a safe path for electricity in the event of a short.
• setup
  • Break off tabs for multi-gang installation.

Getting to Know Your Dimmer

raise the dimming percentage to 100%. Press the bottom of the paddle to
turn the light off.
LED Indicator| Indicates the current state of the device. Refer to LED Locator
Light Explanations for detail.
Dimmer Paddle| Controls and displays the dimming percentage. Press (+/-) to
adjust the light in 2% increments. Hold (+/-) to adjust the light to 20%
increments.
EZ Button| Used to enter setup mode.

Reset To Factory Default

• Deleting a device from the app will reset it to factory defaults.
• To manually reset the device to factory defaults, press and hold the EZ button for 10 seconds until you see the LED blink red, then release.
• The LED will change to solid red when the reset is complete.

LED Light Explanations

FAQS

• Question: How can I contact customer support?
  • You can reach our customer support team through the following channels:
  • Phone: 1-877-833-3303 (8:00 am to 8:00 pm EST, Monday-Friday)
  • Email: [email protected].
  • Chat: https://www.legrand.us/radiant/smart-lighting.aspx. (Click on the chat icon to open a dialogue box)
• Question: What are the warranty terms for this product?
  • Any changes or modifications to this device that are not expressly approved by the manufacturer will void the warranty and the user’s authority to operate the equipment.

BEFORE YOU START

Review this guide in its entirety. Consult an electrician with any questions or if you are unsure of your abilities.
Warning: Incorrect installation could result in death, serious injury, and/or damage to your home or devices.
CAUTION: To reduce the risk of injury and/or overheating and damage to other equipment:

• Do not install to control a receptacle or a motor-controlled appliance.
• For dry, indoor use only.
• Do not use it to power medical equipment.
• Connect the smart dimmer to a 120 VAC, 60 Hz power source ONLY.
• Always use copper wire to install the smart dimmer & follow all applicable local & national electrical codes.

WHAT YOU NEED

Required:

• Phillips head screwdriver
• Flat blade screwdriver

You May Also Need:

• Voltage tester, pliers, wire cutter, wire stripper, electrical tape, flashlight, wiring leads (included), and wire nuts (included).

INSTALLATION

1. Turn Off Power To Device At Circuit Breaker
   • NOTE: Ensure power is off to all devices in the electrical box.
2. Remove Existing Device (if applicable)
   • Check for the following wires:
   • a. HOT or LINE: Receives power from the circuit box. Referred to as “hot” for this guide. Do not touch or let “hot” wire contact other wires.
   • b. NEUTRAL: Creates a path to return current to the power source when the device is off. Required for your dimmer installation.
   • c. GROUND: Provides a safe path for electricity in the event of a short circuit.
3. Wire Smart Dimmer
   • a. Connect the WHITE neutral wire in the box to the Neutral terminal marked “WHITE” using #12 or #14 AWG wire stranded or solid copper conductors. Strip the wire to the length shown on the back of the product. Torque to 14 16 lbf in.
   • b. Connect the BLACK Hotwire in the box to the Hot terminal marked “HOT” using #12 or #14 AWG wire stranded or solid copper conductors. Strip the wire to the length shown on the back of the product. Torque to 14 16 lbf in.
   • c. Connect the GREEN ground wire on the dimmer to the ground wire(s) in the box with the wire nut provided.
4. Secure Smart Dimmer
   • a. Fold wires into the electrical box, taking care not to pinch a wire.
   • b. Use included screws to secure the smart dimmer to the electrical box.
   • c. Snap on the radiant wall plate.
   • d. If installing in the multi-gang application, break off the tab at the top and bottom of the strap.
   • SETUP
   • This device is designed to work with a Zigbee Gateway. Follow the instructions from your app to finish setting up your dimmer.
5. Set UP Your System
   • a. Download and launch the Legrand Home + Control app. The app is available on the App Store or Google Play.
   • b. Connect your smart device to your home network by following the step-by-step instructions in the app.
   • c. Use the app to control your smart device.
   • For the most recent instruction sheets or more information on this product, please see this link or scan the QR code: https://www.legrand.us/p/WZ3RL64wh.

GETTING TO KNOW YOUR DIMMER

to raise the dimming percentage to 100%. Press the bottom of the paddle to turn the light off.
2| LED Indicator| Indicates the current state of the device. Refer to “LED Locator Light Explanations” for details.
3| Dimmer Paddle| Controls and displays the dimming percentage. Press (+/-) to adjust the light in 2% increments. Hold (+/-) to adjust the light in 20% increments.
4| EZ Button| Used to enter setup mode

• Reset To Factory Default Deleting a device from the app will reset it to factory defaults.
• To manually reset the device to factory defaults press and hold the EZ button for 10 seconds until you see the LED blink red then release.
• The LED will change to solid red when the reset is complete.

LED Light Explanations

Legrand reserves the right to change specifications without notice.

FCC

REGULATORY INFORMATION FCC NOTICE:

• This device complies with Part 15 of the FCC rules.

Operation is subject to the following two conditions:

1. this device may not cause harmful interference, and
2. this device must accept any interference received, including interference that may cause undesirable operation.

This equipment has been tested and found to comply with the limits for a Class B digital device, under Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used by the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna
• Increase the separation between the equipment and the receiver
• Connect the equipment to an outlet on a circuit different from that to which the receiver is connected
• Consult the dealer or an experienced radio/TV technician for help This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment.

This equipment should be installed and operated with a minimum distance of 90 mm between the transmitter’s radiating structure(s) and the body of the user or nearby persons.
NOTE: Any changes or modifications to this device that are not expressly approved by the manufacturer will void the warranty and the user’s authority to operate the equipment.

• Contains FCC ID: 2AU5D WNZED
• IC NOTICE: This device complies with Industry Canada license-exempt RSS standards.

Operation is subject to the following two conditions:

1. this device may not cause interference; and
2. this device must accept any interference, including interference that may cause undesired operation of the device.

RF EXPOSURE STATEMENT:
This equipment meets the SAR evaluation limits given in RSS 102 Issue 5 requirements at the minimum separation distance of 90 mm from the human body. Note: Any changes or modifications to this device that are not expressly approved by the manufacturer, will void the warranty and the user’s authority to operate the equipment.

• IC: 25764 WNZED
• HVIN: WZ3RL64

Catalog Number(s)

• Country of Origin: Made in China
• No: 341415 1/23
• WZ3RL64 Wireless AC Smart Dimmer with Zigbee

References

• Patents | Legrand
• Legrand CA | Delivering and Managing Power, Light, and Data
• Legrand US | Delivering and Managing Power, Light, and Data
• Patents | Legrand
• Server Error Page
• Server Error Page
• Smart Lighting from the radiant Collection ⎸Legrand

Read User Manual Online (PDF format)

Download This Manual (PDF format)

Download this manual  >>