INTASTING HB-A8 Nut Milk Maker User Manual

HB-A8 Nut Milk Maker
User Manual

PRODUCT DIAGRAM

PACKAGE CONTENTS

1x Power cord
1x Brush
1x Measuring cup

DESCRIPTION OF EACH PART

Lid: Sealing ring inside.
Steam hole: Used to dissipate heat and allow food to simmer fully.
Cup: Food-grade high boron glass with heating device at the bottom is used for boiling soup.
Handle: For the grip position when removing the cup.
Blade: Made of stainless steel, it is used to cut and crush all kinds of food.

SPECIFICATION

Warm,Water Boil,Self Clean

OPERATION PANEL

OPERATION GUIDE

1. Pour the cut ingredients no longer than 0.4 inch into the cup, add an appropriate amount of water into the cup, the amount should be kept between the upper and lower water levels, and do not exceed or be too low.
2. Align the end of the lid with the top of the handle (as shown in the picture).
3. Connect the power cord, press the “Start/Cancel” key after turning on the power, then press the required function key, and then press the “Start/Cancel” key to start working.
4. When the work is completed, the machine will emit a “beep” soundfor 10 seconds, at this time, the power cord can be unplugged from the power socket.
5. When pouring out, hoia tne nanale tigntly with one hand and hold the bottom of the machine with the other hand to pour out the food. Beware of steam when lifting the lid to prevent burns.

Notice:

1. The function button corresponding to the Menu must be pressed, otherwise the produced drink will have a bad taste and cannot be cooked through. In severe cases, it may cause overflow or sticky bottom.
2. Since there is a detection signal in the cup, please do not lift the cup cover while the machine is working, causing the machine to prompt and alarm not to work.
3. Please do not lift the cup cover during the working process of the machine, which may cause burns or mechanical injuries.

CLEANING

1. Before cleaning, the power must be unplugged.
2. When cleaning the cup body, please pay attention to the sharp blade and be careful not to scratch it.
3. Do not use chemicals, such as alcohol, to wipe.
4. Do not rinse the cup directly with water to avoid water entering the interior.
5. If there are residues inside the cup that are difficult to clean, soak it in warm water first, then wipe it with a sponge in the same direction, and then rinse it with clean water.
6. Do not store the product in an excessively high place or under pressure, and keep away from heat and fire sources.
7. Please wait for the cup body to cool down and clean it to prevent burns due to residual heat.
8. After cleaning the product, please use a dry cloth to wipe the remaining water stains on the main unit and the lid, and put the lid upside down in a cool place to dry.

IMPORTANT SAFETY INSTRUCTIONS

1. Please keep the power cord plug and the body dry.
2. Do not perform operations not described in this manual, and do not disassemble or modify the product without authorization, otherwise it will affect the life of the product.
3. The blade is sharp, please do not touch it.
4. The power cord used must be reliably grounded, and the power supply must be cut off before moving the machine.
5. If you do not use this product, please turn off the switch and unplug it. 6. Do not let children approach or touch the body during use, nor allow children to use it alone, and do not put it in a place where children can touch it during normal storage, so as to avoid unexpected accidents.
6. Pay attention to the storage and protection of the power cord: when taking and storing, be careful not to process, break, pull, twist or lengthenthe power cord arbitrarily, and do not let heavy objects press it, so as not to damage the power cord And cause unexpected failures and accidents.
7. If the power cord is damaged, it must be repaired by a technician at themanufacturer or service or distribution office.
8. This machine adopts a high-speed motor, and it is normal that there will be intermittent fast and slow sounds when crushing.
9. Before the machine works, please cut off the prepared food, about 0.4 inch long.

PRODUCT FUNCTION DESCRIPTION

Function keys
“means”Start/Cancel”key ,” “means”Menu”key, “ “means”Delay”key;
“Room Temp”,”Hot 212F”,”Warm 140F”,”Keep Warm”,”Water Boil”,”Self Clean”

Standby mode
After turning on the power, the screen will display ” 88 “, Simultaneously ” beep ” , enter standby mode
“Start/Cancel”
After power on, press the “Start/Cancel” function key, then press the “Menu”key to select the corresponding program, and then press the “Start/Cancel”function key to start running” button, it will stop working and return to the power-on standby state.
“Menu” &”Start/Cancel”indicator light
First press the “Start/Cancel” button to enter the standby mode, and then each time you press the “Menu” button, you will enter the menu Room Temp, Hot 212F, Warm 140F, Keep Warm, Water Boil, SelfClean 6 program cycle, and then press the “Star Cancel “,starting program

“Delay”
First press the “Start/Cancel” key to enter the standby mode, then press the delay button, and then press the menu to realize the delay function. Each time Delay is pressed, the delay will be 1 hour, and the delay time will cycle from 1 to 18 hours. Note that the delay time already includes the running time of the program. For example, if the “Hot 212F” program is 28 minutes,if you choose a delay of 1 hour, the program will be completed in 1 hour (The “Hot 212F” program will start at 32 minutes after the delay is set)
End of work status
After all functions are finished, the function indicator light goes out, the digital screen displays “–“, and at the same time, 3 beeps indicate the end.
“Room Temp”
First press the “Start/Cancel” key to enter the standby mode, then press the”Menu” key to selectthe “Room Temp” function, at this time the functionindicator light flashes, and the screen displays “06” (indicating the total program duration is about 6 minutes), then press “Start/Cancel” functionkey,the “Room Temp” program starts to run, the indicator light is always on duringthe proqrorn.ond the screen displays a countdown. After the program ends, the function indicator light goes out, the digital screen displays”–“, and atthe same time, 3 beeps indicate the end.(The indicator light does not recover automatically, press the “Start/Cancel” button to return to the normal standby state).
“Hot 212F”
First press the “Start/Cancel” key to enter the standby mode, then press the “Menu” key to select the “Hot 212F” function. “Start/Cancel” function key, the “Hot 212F” program starts to run, the indicator light is always on during the program, the screen displays a marquee when stirring, and the screen displays a countdown when not stirring. After the program ends, the function indicator light goes out, the digital screen displays”–“, and at the same time, 3 beeps indicate the end.(The indicator light does not recover automatically, press the “Start/Cancel” button to return to the normal standby state).
“Warm 140F”
First press the “Start/Cancel” key to enter the standby mode, then press the “Menu” key to select the “Warm 140F” function, , at this time the function indicator light flashes, and the screen displays “9” (indicating that the total program duration is about 9 minutes), and then Press the “Start/Cancel” function key, the “Warm 140F” program starts to run, the indicator light is always on during the program operation, the screen displays a marquee when stirring, and the screen displays a countdown when not stirring. After the program ends, the function indicator light goes out, the digital screen displays”–“, and at the same time, 3 beeps indicate the end. (The indicator light does not recover automatically, press the “Start/Cancel” button to return to the normal standby state).
“Keep Warm”
First press the “Start/Cancel” key to enter the standby mode, then press the “Menu” key to selectthe “Keep Warm” function. “Start/Cancel” function key, the “Keep Warm” program starts to run, the indicator ight is always on during the program work, and the screen displays a marquee. After the temperature reaches 60°C, the screen displays “bb” and the countdown jumps back and forth at the same time. After the program ends, the function indicator light goes out, the digital screen displays”–“, and at the same time, 3 beeps indicate the end. (The indicator light does not recover automatically, press the “Start/Cancel” button to return to the normal standby state).
“Water Boil”
First press the “Start/Cancel” key to enter the standby mode, then press the “Menu” key to select the “Water Boil” function, , and the corresponding function indicator is flashing, then press the “Start/Cancel” function key, “Water Boil” The program starts to run, the indicator light is always on during the program work, and the screen displays a marquee. After the program ends, the machine will give 5 beeps, automatically enter the 60°C heat preservation for 4 hours, and at the same time, the screen will display “bb”. The indicator light bb and the countdown jump back and forth. After 4 hours, the digital screen of the machine will display “–“, and at the same time, 3 beeps will prompt the end.(The indicator light does not recover automatically, press the “Start/Cancel” button to return to the normal standby state).
“Self Clean”
First press the “Start/Cancel” button to enter the standby mode, then press the “Menu” button to select the “Self Clean” function. “Start/Cancel” function key, the “cleaning” program starts to run, the indicator light is always on during the program, and the screen displays a countdown. After the program ends, the function indicator light goes out, the digital screen displays “–“, and at the same time, 3 beeps indicate the end. (The indicator light does not recover automatically, press the “Start/Cancel” button to return to the normal standby state).

RECIPES

“Room Temp” Recipes

Almond Milk

• 2 tablespoons raw almonds
• 1 date, pitted
• 1/4 teaspoon vanilla extract pinch of salt
• 1 cup of water
  *Add ingredients to machine.
  Run a loop by “Room Temp”

Pistachio Milk

• 2 tablespoons raw pistachios
• 1 date, pitted
• 1/4 teaspoon vanilla extract
• 1 cup of water
  *Add ingredients to machine. Run a loop by “Room Temp”

Smoothie

• 1 tablespoon walnuts
• 112 frozen banana
• ½ cup pineapple
• ¼ cup spinach
• 1 tablespoon ground flaxseed
• ½ cup orange juice
• ¾ cup water
  *Add ingredients to machine.
  Run a loop by “Room Temp”

Creamy Blueberry Oatmeal Smoothie

• 1/3 cup blueberries
• ½ banana
• 2 tbsp oats
• 1 tablespoon walnuts
• ¼ cup orange juice
• 1 cup of water
• 1 teaspoon agave nectar or maple syrup
  *Add ingredients to machine. Run a loop by “Room Temp”

“Hot 212F” Repices
Rice Milk

• 2 tablespoons raw/raw white rice, rinsed1-2 dates, depending on sweetness preferred pinch of salt
  *Add ingredients to machine.
  Run a loop by “Room Temp”

soy milk

• 1 tablespoon dried soybeans, rinsed
• 1-2 dates pinch of salt
  *Add ingredients to machine. Run a loop by “Room Temp”

“Warm 140F” Recipes
Peanut Milk

• 2 tablespoons raw unsalted peanuts
• 1 tablespoon maple syrup or 1 pitted date
• ¼ teaspoon vanilla extract (optional) pinch of salt
• ½ cup water
  *Add ingredients to machine.
  Run a loop by “Room Temp”

Hot chocolate

• 4 tbsp cashews
• 1 cup of water
• 1.5 teaspoons cocoa powder
• 1 tablespoon coconut sugar I monk fruit sugar
• ¼ teaspoon vanilla extract
• 5 marshmallows (optional)
• Hershey syrup (optional)
  *Add ingredients to machine.
  Run a loop by “Room Temp”

Dairy Free Cookies and Cream Latte

• 4 Oreos without cream
• 4 tbsp cashews
• 2 tsp sugar
• 1 teaspoon instant coffee
• 1 cup of water
  *Add ingredients to machine. Run a loop by “Room Temp”

TROUBLESHOOTING

2. Send for repair
E3| NTC temperature is too high|
ES| The heating plate keeps heating, and the circuit board does not work| 1. Clean the machine, then let the machine cool down for half an hour before working;
2. Send for repair
E7| Program zero-crossing detection exception| Unplug the plug, power off for 5 minutes, and then power on again.
EB| NTC short circuit| Send for repair
Overflow| Too much water or food| Add water and ingredients as required
Burnt bottom| Too much water or too little food| Add water and ingredients as required

CAUTIONS

When the machine is working, please do not touch the cup shell.
During the working process of the machine, the temperature of the cup body and the cover body will rise, please do not touch it directly with your hands, and do not let children approach or use it.
Do not disassemble, repair or refit by yourself
Self-disassembly or modification can easily lead to poor assembly and unexpected failures and accidents, which will seriously affect consumer rights.

1. Do not put the main unit directly nto the refrigerator or freezer, because the rapid cooling and low temperature will cause “condensation” inside the cup holder.It is easy to damage the parts of the electrical body and cause the body to malfunction.
2. During the production process, please do not open the lid at will to prevent being scalded by the water vapor gushing from the high-temperature surface and the machine will stop working.
3. When cleaning the cup body, it is forbidden to wash it directly with water, so as to avoid water entering the body and causing malfunction or unexpected accidents.
4. Please pay attention to the location of the machine, do not place it on the table or in an unstable position. And it needs to keep a certain distance from the wall or other objects to keep the periphery of the machine well ventilated and ensure the service life of the machine.

POWER CABLE USE

Do not use a power supply with a voltage other than 120V-: a power supply lower than 120V- will not allow the body to operate normally, which will affect the quality of use and indirectly affect the life of the body. Do not touch the power cord and electrical appliances with wet hands to avoid electric shock.
Do not bend the power cord: When in use, do not bend, bundle, or process the power cord yourself.Do not share the same socket with other electrical appliances: sharing the socket can easily cause the socket to overheat, causing the power supply to catch fire and causing unexpected accidents. If there is any abnormal phenomenon during operation, please unplug immediately; after use, please turn off the power and unplug the power socket.When unplugging, do not pull the power supply directly to avoid electric shock.If the supply cord is damaged, it must be replaced by the manufacturer or a professional similar to its service department in order to avoid a hazard.

Special statement
All the contents of this document have been carefully reviewed, if there areany typographical errors or contentlf there is any misunderstanding on the above, please consult our company.
In addition: If the product has technical improvements or parameter changes, it will be compiled into the new version of the manual without prior notice.Notice, if there is any change in the appearance and color of the product, please refer to the actual product!

NEED HELP? TALK TO US!
CUSTOMER SUPPORT
Phone: +1 833 721 2799 (US) Mon-Fri 9 am – 5 pm (PST)
****support@intasting.com
24-Months Warranty
Shenzhen Intasting Technology Co., LTD 518100
Guangcong Shenzhen
Xinghe World Tower C, 33rd Floor
Longhua District
Desicned by INTASTING in California, Made in China

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>