milwaukee 2879-20 Force Logic Cordless 15t Crimper Installation Guide

milwaukee 2879-20 Force Logic Cordless 15t Crimper

Product Information

• Product Name: M18 ONE-KEY 15T CRIMPER
• Catalog No.: 2879-20
• Serial No.: K41A
• Bulletin No.: 54-47-2880
• Revised Bulletin Date: June 2023

Best Practices
Follow these best practices for service:

• Use the specified service tools and fixtures.
• Adhere to the torque specifications.

Product Usage Instructions

Service Parts List
To order parts, provide the catalog number and serial number.

Service Tools / Fixtures
The following service tools and fixtures are available:

• Indicator
• Fill Bottle
• Seal Pick Tool
• Filling Syringe (Quantity of 5)
• Filling Needle (Quantity of 10)
• Dump Valve Tool
• BD Install Tool
• Sequence Valve
• One KeyTM Adaptor
• Crimping Service Tool Load Cell
• Load Cell Fixture
• Service Wrap Fixture
• Pressure Sensor Crowfoot Wrench
• Large Die Pin Torque Adapter
• Small Die Pin Torque Adapter

Service Videos, Repair Guides, and Verification Procedures
Service videos and repair guides are available to assist with repair and maintenance of the ABB Smart Tool +. They provide instructions on special assembly, settings, and procedures. Verification procedures are also covered in the service videos and repair guides.

Specifications

SERVICE PARTS LIST

BEST PRACTICES when Servicing FORCELOGIC™ Tools

• Caution: Always assume Hydraulic tool is under pressure, before starting any repair procedures, manually engage the relief valve. Confirm no hydraulic pressure remains.
• Important! The pressure sensor is a monitoring device that is calibrated with the electronics assembly. Always replace pressure sensor and electronics assembly as a set!
• Always wear P.P.E. (Personal Protective Equipment) when working with hydraulic fluid.
• Do not use Hammers or Impact tools.
• Do not use sharp metal objects on seals or sealing surfaces.
• Always use recommended service tools and fixtures.
• Always ensure new hydraulic parts are free of burrs or defects.
• Always establish a clean work area free of dirt and debris.
• Always insure that clean parts are used prior to assembly.
• Always follow proper torque specifications.
• Always confirm repair by testing on verification fixtures.
• Always use appropriate hydraulic oil, see operator’s manual.
• Always remove battery pack before changing or removing accessories. Only use accessories specifically recomended for this tool. Others may be hazordous. For a complete listing of accessories, go online to www.milwaukeetool.com or contact a local MILWAUKEE distributor.

SERVICE TOOLS / FIXTURES

• Service Videos are available to aid in repair and maintenance of ABB Smart Tool +.
• Repair Guides are available that illustrate/explain any special assembly, settings or procedures.
• Verification Procedures are covered in service videos as well as repair guides.

MILWAUKEE TOOL www.milwaukeetool.com 13135 W. LISBON RD., BROOKFIELD, WI 53005

SERVICE PARTS EXPLODED VIEW

*Back off 1-5/8 to 1-7/8 turn after tightened by fixture.

Accessories:

SERVICE WIRING DIAGRAM

AS AN AID TO REASSEMBLY, TAKE NOTICE OF WIRE ROUTING AND POSITION IN WIRE GUIDES AND TRAPS WHILE DISMANTLING TOOL. BE CAREFUL AND AVOID PINCHING WIRES BETWEEN HANDLE HALVES WHEN ASSEMBLING.

NOTE:
Cylinder is removed for a better visual representation to wire traps and channels.

LUBRICATION INSTRUCTIONS

ASSEMBLY DETAIL 3 LOCTITE AND GREASE APPLICATION

• = 243 BLUE LOCTITE, TTI P/N: 900239017, MET: TBD
• = TYPE ST-80 WHITE LITHIUM GREASE, TTI P/N: 903473001, MET: TBD
• = 263 RED LOCTITE®, TTI P/N: 900239048, MET: TBD
• = GREASE, TYPE “S2”, TTI P/N: 902123001, MET: TBD

NOTE
Regarding parts to receive thread locking sealant: Place one to two drops of the recommended Loctite® thread locking sealent (or the equivelant) to the threads of parts shown prior to installation.

NOTE
Regarding parts to be lubricated: Apply a light coating of grease to all highlighted parts shown prior to installation. Reference the key below for grease types.

• P/N: 697171001
  APPLY S2 GREASE 0.3G REF COATING GREASE EVENLY ON ENTIRE OD

• P/N: 697170001
  APPLY S2 GREASE 0.IG REF COATING GREASE EVENLY ON THE CONE

• P/N: 643488001
  APPLY S2 GREASE 0.IG REF AT THE HOLE OF 697170/697171001

WARNING:

1. NEED TO PRESS THE RELEASE BUTTON 1697171001/5 TIMES AFTER FINISHED THE ASSEMBLY TO CHE CK WHETHER HAVE BINDING ISSUE.
2. NEED TO CLEAN THE EXTRA GREASE WHICH COME OUT TO OUTSIDE.

FAQ

Where can I find a complete listing of accessories?
For a complete listing of accessories, visit the Milwaukee Tool website or contact a local Milwaukee distributor.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>