HS DC 5V Colorful LED Electronic Clock Kit User Manual
- June 16, 2024
- HS
Table of Contents
HU-058 RGB Colorful LED Digital Electronic Clock
DIY Kit
Introduction:
HU-058 is a RGB Colorful LED Digital Electronic Clock DIY Kit. It will display current date, time, temperature in the real time, Alarm clock music.User can set alarm as your needs.lt is easy to operate, beautiful design, very suitable for home or office environment.
Feature:
- RGB Colorful LED display: Each digital tube can be randomly displayed or assigned a display color. Each parameter can also specify a display color.
- Four Display Mode: Time, Time/Temperature, Time/Date/Week, Time/Temperature/Date/Week.
- Automatic Brightness Adjustment: Built-in photosensitive sensor which can automatically adjust the brightness of the display screen. Users can also set Low/Middle/High levels of fixed brightness.
- Three Alarm Clock: Built-in 3 sets of alarm clocks. Users can ON/OFF Alarm1/Alarm2/Alarm3 according needs. It can be turn on at the same time or only one alarm clock can be turn on.
- Four Alarm Ring: Built in 4 different alarm ringtones, users can freely switch.
- C/F Temperature: It can display temperature in Celsius Degree or Fahrenheit Degree as your need.
- Temperature value can be calibrated.
- Display time can be calibrated.
- Voice Hourly Report: Buzzer alarm prompt once on hour.
- 12H/24H Display: It will display AM or PM if select display time in 12H system.
- Power-down memory. The time and set parameters will run automatically after installing the built-in battery CR1220 without re-calibrate and setup.
- DIY Hand Soldering. It’s a DIY kit which comes with various components. User need to install each component by hand. It not only can exercise and improve soldering skills, but also increase the interest in electronic technology. Great for electronics hobbyists, beginners, school and home education.
3.Parameter:
- Work voltage:DC 5V
- Display Color:RGB
- Power Interface: Micro USB
- Work Temperature:-20C~85″C
- Work Humidity:0%~95%RH
- Size(Installed):1652021mm
Function:
- Display time: Hour, Minute, Second.
- Display date: Year, Month, Day.
- Display week.
- Display current temperature in Celsius or Fahrenheit .
- Adjustable alarm clock music: 4 music.
- Voice Hourly Report.
- Automatic brightness adjustment.
- Set display mode.
- Adjustable alarm clock: 3.
- Set 12H/24H display mode.
- Calibration time display value.
- Calibration temperature display value.
Set Method:
- It displays the current time by default in hour-minute. Note: display mode can be modified in the next set methods.
- Switch Display Brightness: Short press SW2/Down button can modify display Brightness: Automatic brightness adjustment mode, Low brightness mode, Medium brightness mode, High brightness mode.
- Turn OFF Alarm Ring: Press any one button can turn OFF alarm ring. The alarm clock ring can also automatically stop after 60 seconds.
- Factory Default: Press SW1/UP and SW2/Down simultaneously to restore factory settings.
- Set Color Display Mode:
5.1>.Short press SW1/UP button enter into Set Color Display Mode.
5.2>.SW1/UP Button: Save parameter and enter into next function at set mode.
5.3>.8W2/Down Button: Increase the parameter value by +1 for each press at set mode. Hold down to continuously and quickly modify parameter values. Note: It will automatically increase from the minimum value after the parameter value reaches the maximum value.
Set Mode | Display | Setting Steps | Descriptions |
---|---|---|---|
Color Display | dC-3 | 1.Press SW2/Down Button can switch display mode dC-0, |
dC-1, dC-2, dC-3.
2.Press SW1/UP button can save and enter into next step.| dC-0: 4 digital
tubes randomly displays different colors.
dC-1:4 digital tubes randomly displays the same colors.
dC-2:Time/Date/Temperature/Week can each select the a specified display color.
dC-3:4 digital tubes can each choose a specified color.
Time Color| 8:00| 1.Press SW2/Down Button can change current display color.
2.Press SW1/UP button can save and enter into next step.| It is available just
only for dC-2 Color Display Mode. Other modes do not have this option.
Date Color| 01-01| 1.Press SW2/Down Button can change current display color.
2.Press SW1/UP button can save and enter into next step.
TemperatureDisplay Color| 251 .’| 1.Press SW2/Down Button can change current
display color. 2.Press SW1/UP button can save and enter into next step.
Week Color| – 1-| 1.Press SW2/Down Button can change current display color.
2.Press SW1/UP button can save and enter into next step.
Each Bit Color| 1234
1 Flicker| 1.Press SW2/Down can set #1 digital tube display color. 2.Press
SW1/UP button can save and enter into next step.| It is available just only
for dC-3 Color Display Mode. Other modes do not have this option.
2 Flicker| 1.Press SW2/Down can set #2 digital tube display color. 2.Press
SW1/UP button can save and enter into next step.
3 Flicker| 1.Press SW2/Down can set #3 digital tube display color. 2.Press
SW1/UP button can save and enter into next step.
4 Flicker| 1.Press SW2/Down can set #4 digital tube display color. 2.Press
SW1/UP button can save and exit set mode.
Set Time Mode:
6.1>.Keep press SW1/UP button more than 2second enter into Set Time Mode.
6.2>.SW1/UP Button: Save parameter and enter into next function at set mode.
6.3>.SW2/Down Button: Increase the parameter value by +1 for each press at set
mode. Hold down to continuously and quickly modify parameter values. Note: It
will automatically increase from the minimum value after the parameter value
reaches the maximum value.
Set Mode | Display | Setting Steps | Descriptions |
---|---|---|---|
Year | 2023 | ||
23 Flicker | 1.Press SW2/Down Button switch Year value. | ||
2.Press SW1/UP button can save and enter into next step. | Set range is |
2000-2099.
Date| 01-02
01 Flicker| 1.Press SW2/Down Button switch Month value.
2.Press SW1/UP button can save and enter into next step.| Week value will be
automatically adjusted based on the date.
02 Flicker| 1.Press SW2/Down Button switch Day value.
2.Press SW1/UP button can save and enter into next step.
Time| 07:59
07 Flicker| 1.Press SW2/Down Button switch Hour value.
2.Press SW1/UP button can save and enter into next step.| Second is
automatically set to 0
59 Flicker| 1.Press SW2/Down Button switch Minute value.
2.Press SW1/UP button can save and enter into next step.
12H/24H| 24H| 1.Press SW2/Down Button switch 12H or 241-I.
2.Press SW1/UP button can save and enter into next step.| 12H: 12 hour display
system with AM and PM. 24H: 24 hour display system without AM and PM.
1.Its set range is -58s – +58s.
2.This error value is for 24 hours a day.
---|---|---|---
Error Value| H00 00 Flicker| 1.Press SW2/Down Button change error value.
2.Press SW1/UP button can save and exit set mode.| 3.1t can be set to -1 –
-58s if clock’s time is faster than the actual time. Automatically reduce by
1-58s per day.
4.1t can be set to 1-58s if clock’s time is slower than the actual time.
Automatically increase by 1-58s per day.
5.There is no error compensation value, if set to 00.
Component listing:
NO. | Component Name | PCB Marker | Parameter | QTY |
---|---|---|---|---|
1 | Metal Film Resistor | R1,R2,R5 | 10Kohm | 3 |
2 | GL5539 Photoresistor | R3 | 1 | |
3 | Thermistor | R4 | 1 | |
4 | 0805 SMD Capacitor (Installed) | C1,C2 | 1uF | 2 |
5 | Ceramic Capacitor | C3,C4 | 0.1uF | 2 |
6 | Ceramic Capacitor | C5,C6 | 22pF | 2 |
7 | 0603 SMD RGB LED (Installed) | LED1-LED36 | Common Anode | 36 |
8 | S8550 Transistor | Q1 | TO-92 | 1 |
9 | Passive Buzzer | LS1 | 1 | |
10 | AiP33628 Driver IC (Installed) | U1,U2 | SSOP-28 | 2 |
11 | DS1302 Clock IC | U3 | DIP-8 | 1 |
12 | IC Socket | U3 | DIP-8 | 1 |
13 | STC8G1K17-38I Controller | U4 | DIP-16 | 1 |
14 | IC Socket | U4 | DIP-16 | 1 |
15 | Black Button | SW1,SW2 | 2 | |
16 | Black Button Cap | SW1,SW2 | 2 | |
17 | Micro USB Socket | USB1 | 2Pin | 1 |
18 | Crystal Oscillator | Y1 | 32.768KHz | 1 |
19 | CR1220 Battery | BT1 | 1 | |
20 | CR1220 Battery Socket | BT1 | 1 | |
21 | ‘ + ‘ Screwdriver | 1 | ||
22 | Micro USB Power Wire | 1 | ||
23 | Clock Case | 1655021mm | 1 | |
24 | Screw | 4 | ||
25 | PCB Circuit Board | 146*45mm | 1 |
Note: Users can complete the installation according to the PCB silk screen and component list.
Application:
- Practical at home
- Indoor display
- Simple appearance, easy office
- Wall decoration
Installation Tips:
- User needs to prepare the soldering tool at first.
- Please be patient until the installation is complete.
- The package is DIY kit.It need finish install by user.
- The soldering iron can’t touch the components for a long time(1.0 second), otherwise it will damage the components.
- Pay attention to the positive and negative of the components.
- trictly prohibit short circuit.
- Install complex components preferentially.
- Make sure all components are in right direction and right place.
- Please wear anti-static gloves or anti-static wristbands when installing electronic components.
- Itis strongly recommended to read the installation manual before starting installation!!!
Schematic:
Install shown steps:
Functional Characteristics
-
RGB Adjust Display Color
27 colors and randomly displayed -
12124H System
12H means 12 hour system
24H means 24 hour system -
Automatic Brightness Adjust
1.Adaptive Brightness Mode
2.Low Brightness Mode
3.Medium Brightness Mode -
Main Display Interface
Time, Temperature, Date, Week|
1.0nly display Time
2.Display Time/Temperature
3.Display Time/Date/Week
4.Display Time/Temp…/Date/Week -
3 Alarm for every day or
Monday to Friday or
Monday to Saturday.
4 Alarm Ring Music
AU 0: Jasmine flower
AU 1: A Thousand Year Love.
AU 2: Ode to Joy.
AU 3: Happy Birthday to You. -
Time Error Compensation Value Set range is -58s ~ +58s for each day.
-
Hourly Report 07+21 means Hourly Report from 7 to 21 o’clock.
Turn OFF Hourly Report function if xx is more than yy such as 08+07. -
Display Current Temperature The clock itself will generate heat, which will affect the display value. The higher the brightness, the greater the error.
Step 9: Install 1pcs DIP-8 IC Socket at
U3.There is a gap mark on one end of the IC Socket and there is a gap mark on
PCB silk screen where the IC Socket can place on. These two marks are
corresponding to each other and are used to specify the installation direction
of the IC Socket. Step 14: Install 1pcs DIP-8 IC DS1302 Clock at
U3. There is a gap mark on one end of the IC and there is a gap mark on DIP-8
IC Socket where the IC can place on These two marks are corresponding to each
other and are used to specify the installation direction of the IC.Step 16: Install 1pcs CR1220 battery as shown.
Note: The positive electrode of the battery contacts the metal spring of
the battery holder. Step 17: Place PCB on Clock Case. Pay
attention to the installation positions of the two sensors and two buttons.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>