SHARP ES-G80G Washing Machine User Manual

ES-G80G Washing Machine

Product Information

Specifications:

• Model: ES-G80G

• Capacity: 8.0kg

• Power Supply: 220-240V~ 50Hz

• Water Consumption: 10/66L, 9/61L, 8/56L, 7/52L, 6/48L, 5/44L,
  4/40L, 3/36L, 2/32L, 1/28L

• Water Pressure: 0.03MPa~0.85MPa

• Wash Power: 480W

• Spin Power: 310W

• Weight: About 34kg

• Dimensions: W560mm x D585mm x H944mm

Product Usage Instructions

Unpacking:

1. Unpack the carton and take out the bottom cover.

2. Open the top lid of the washing machine and take out all of
the accessories.

3. Remove all wrappers, including the polystyrene base.

4. Keep all the packaging for reuse in case the machine needs to
be transported again.

Installing the Bottom Cover:

1. Slightly lean forward the front side of the washing machine,
following the direction of the arrow.

2. Put the bottom cover into the slot of the base.

3. Use two screws to fix the bottom cover on the base.

Positioning:

1. Make sure the washing machine is horizontal.

2. Use a tied thread with plumb to check if it is
horizontal.

3. Adjust the adjustable foot:

a) Lift up the adjustable foot gently
and loosen the adjustable nut.

b) Twist the adjustable foot to adjust
the height.

c) Fasten the nut after adjustment.

FAQ (Frequently Asked Questions)

Q: What should I do if there is an abnormal display on the

washing machine?

A: If you see an E0, E1, E2, E3, E4, or E5 on the display,
follow the instructions below:

– E0: Close the top lid and clear up the alarm.

– E1: Close the top lid and clear up the alarm. If draining is
not reaching the water level setting after 15 minutes, refer to the
manual to settle it.

– E2: Close the top lid and clear up the alarm. If spinning does
not balance after 20 minutes of water filling time, refer to the
manual to settle it.

– E3: Open the top lid and make sure the laundries are placed
equally, then close it and clear up the alarm.

– E4: Open the top lid and refer to the manual to settle it.
Then close the top lid and clear up the alarm.

– E5: Open the top lid and refer to the manual to settle it.
Then close the top lid and clear up the alarm.

ES-G80G
WASHING MACHINE
Operation Manual
If the appliance is sold or transferred to another owner or if you moved house and leaving the appliance, always ensure the manual is supplied with the appliance in order for the new owner can get to know its functions and its relevant warnings. These warnings have been provided for your safety. You MUST read them carefully before installing or using the appliance.

Contents
Before using Parts name…………………………………. 1 Cautions……………………………………. 2 Installation and adjustment…………….. 4 How to use drain pipe……………………. 5 Water inlet installation…………………… 6 Operation Preparation before operation………….. 8 Load laundries…………………………….. 9 Use of detergent………………………….. 9 Control panel instructions……………… 10 Operation steps………………………….. 12 Additional functions…………………….. 15 Others Maintenance………………………………. 16 Common non-fault phenomenon………17 Specification………………………………. 20

ES-G80G
8.0kg
220-240V~ 50Hz 10/66L 9/61L 8/56L 7/52L
6/48L 5/44L 4/40L 3/36L 2/32L 1/28L
0.03MPa~0.85MPa
Wash:480W Spin :310W
About 34kg
W560mm D585mm H944mm

3

Drain hose Drain hose

Screw (2pcs)

Warning symbols Pay attention to the warning symbols.There may be serious risks on personal safety or may damage the washing machine if not followed.
Prohibited symbol The contents of this symbol are prohibited.It may damage the appliance and can lead to injury.

220-240V.

This appliance is not intended for use by persons(including children) with reduced physical, sensory or mental capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction concerning use of the appliance by a person responsible for their safety.Children should be supervised to ensure that they do not play with the appliance.
Notice

Please install and adjust the machine according to the requirements of the manual. Correct operation is very important for your safety.
Unpacking
Unpack the carton and take out the bottom cover. Open the top lid of washing machine and take out all of the accessories. Remove all wrappers, including the polystyrene base. You are advised to keep all the packaging for reuse in case the machine is to be transported again.
Installing the bottom cover
To prevent damage from mouse/rats or other insects, please install the bottom cover as shown.

Bottom Cover

Slightly lean forward the front side of washing machine, following the direction of arrow and put the bottom cover into the slot of base.

Use two screws to fix the bottom cover on the base.

Positioning
The distance between the washing machine and the wall should be more than 50mm, and the maximum allowable angle of the shank base of the machine is 1° The slanting or rough ground may cause operating stopped or unstable, please adjust it with the following methods:
Make it horizontal.
Use a tied thread with plumb to check if it is horizontal.

Adjust the adjustable foot 1) Lift up the adjustable foot gently, loose the adjustable nut
and twist the adjustable foot.
2) Fasten the nut after adjustment.

°
Adjustable nut Adjustable foot

1. Abnormal display

Display E0 E1
E2

Explanation

Settlement

The top lid is opened when preset is started

Close the top lid and clear up the alarm

After 15 minutes of draining Open the top lid and refer to the “before using”

time and still not reaching procedures and “common non fault phenomenon”

the water level setting

on this manual to settle it, then close the top lid and clear up the alarm.

The top lid is open when

spinning

Close the top lid and clear up the alarm

E3

Spin does not balance

After 20 minutes of water

E4

filling time and still not reaching the water level

setting

E5

The top lid is opened

child-lock

after setting child-lock

light flashing

synchronously

Open the top lid ,make the laundries place equally, then close it and clear up the alarm
Open the top lid and refer to the “before using” procedures and “common non fault phenomenon” on this manual to settle it, then close the top lid and clear up the alarm.
Close the top lid and clear up the alarm

Turn the power off and leave it for 1minute.

F1

Water level sensor is wrong

After that,turn the power on again. If the same error is displayed,cut the

power suppy and call a technicians.

2. Imbalance adjustment During spinning, if the laundries are not placed equally in the tub, it would cause violent vibration.This machine has imbalance adjustment function, and the vibration testing system will supervise the running. Once vibration is beyond certain level, the adjustment system will start automatically to adjust the imbalance.
3. Power supply is cut off automatically 1) Press the power supply button and did not start the program in 10 minutes, the power supply will be cut off automatically. 2) After the washing is finished, buzzer will activate. The power supply will be cut off automatically.
4. Child lock function 1) If set child lock function, all the buttons will be locked including POWER. If the top lid is opened during the washing machine working, the washing will be stopped and give an alarm.But if you can close the top lid in 5 seconds, the washing machine will stop alarm and continue working. If can not close the top lid in 5 seconds,the washing machine will begin draining if there is water in the inner tub is 5 cm higher, alarm will be given every 10 minutes (alarm is always given). When the draining is finished, the washing machine will be in the stare of washing, if close the top lid, the washing machine is unlocked and start working as previous setting.
2) Once child lock is set, if open top lid over 5 seconds during washing or rinse ( there is water in the inner tub),washing machine will drain and give an alarm. If you unlock the function during draining, the washing machine will add water to setting water level and continue working.

Clean the lint filter
It is necessary to use lint filter during washing. After washing, please clean the lint filter in time. Clean the lint filter according to the following steps: 1. Pull out the lint filter. 2. Turn the filter net inside out
and wash it. 3. Reverse back the filter net
and remount it.
Groove Magic filter cleaning 1. pull out magic filter 2. open the box and clean it 3. close it and reinstall it 4. check if the lint block part is in good
condition
press this part and pull out to take out the magic filter
lint block part (black rubber)

Set the drainpipe clip into the drainpipe to 2-3cm(from the drainpipe end without hook). Then install the drainpipe into the drainpipe connector and fixed it with the drainpipe clip. After that put up the drainpipe clip to fasten the grip.
1.Take off the drainpipe and drainpipe clip from the drainpipe connector. Put soft mat on the floor and gently put down the washing machine front side on the mat. Unscrew the back cover by screwdriver and gently unmount the back cover. Unscrew the drainpipe connector (on the right of the washing machine), then loosen the drainpipe connector.

(Washing machine’s inside view)

(Washing machine’s right side view)

4.Pull the inner drainpipe to another side,

3.With proper force, take off the drainpipe gate stopper avoid distortion of the inner drainpipe.

on the left side of the washing machine. The drainpipe As per foregoing description, fix the inner

gate stopper is fixed on washing machine base with drainpipe with the drainpipe hoop. Fix the

two clips, look for the fixing orientation at the back the drainpipe connector with the screw

opening.

and install the the drainpipe gate stopper

on the other side of the washing machine.

Gently stand the washing machine, fix the

back cover with screw and install the

drainpipe and drainpipe clip into the

(Washing machine’s left side view)

drainpipe connector.

The drainpipe should drain smoothly 1.The height of the drainpipe should be less
than 10cm, otherwise the drainage will not be smooth and need a long time to drain, the machine may stop during working. 2.Do not step on or press the drainpipe.

4. Purchase a proper hose if you need additional drainpipe. Its diameter should not be less than 30mm and length should not exceed 1.5m.

3.Cut the drainpipe if it is too long. Cut the front end of the drainpipe slantingly to make drainage smoothly.

If the additional drainpipe is too long, cut some at A or B point.
AB

Tap selection
Suitable tap

Not suitable tap

10mm

The front end should be longer than 10mm. The tap exit end face should be flat and smooth, if not file it to avoid leakage.
Connect the inlet hose connector to the tap
1. Press down the slider and remove the inlet hose connector from the inlet hose , like below illustration 1.
2. Loosen the four bolts on the inlet hose connector till the tap can be accessed, then set the inlet hose connector in the tap, see illustration 2.(if the tap caliber is too large and could not set the inlet hose end, unscrew the four bolts and take out the bushing, tap exit end must be flat, otherwise it will leak, see illustration 3)

3. Fasten the four bolts in the inlet hose connector evenly, see illustration 4. 4. Twist the fastening as seen on the illustration Remark: before twisting the nut, the threading is about 4mm above the upper surface of the nut, after twisting,
the threading is less than 2mm above the upper surface of the nut, see illustration 6.

Soak function

Press and hold for 2 seconds

When you choose “Normal” , “Speedy” , “Air Dry” , “Blanket” , “Soft” , “Baby” or “Delicate” program, you can use soak function before wash. After selecting the program, press “WASH” key for 2 seconds to set soak function.

When you set this function, the wash procedure can not be cancelled.

Child lock

Press and hold at the same time for 3 seconds

1 .Before start You can set child lock by pressing and holding “WATER LEVEL” key and “PRESET TIME” key at the same time for 3 seconds. “CHILD LOCK” is displayed on the operation panel. Press “START/PAUSE” and the machine is locked. Press and hold these keys for 3 seconds again to unlock this function.
2 .After start You can set this function with the same way as 1 , the machine is locked directly with the same way as 1 to unlock this function.

Add water

During wash (including rinse), press “WATER LEVEL” key to add water as necessary. Un-press will stop adding.
Or pause the washing machine by pressing “START/PAUSE” key, and press “WATER LEVEL” key to select water level, then press “START/PAUSE” key again.
When you reset higher water level than present:
The washing machine will add water to the setting level automatically and continue working.
When you reset lower water level than present:
The new water level will be valid in next water inlet.

Put the slider down and insert the inlet hose into the inlet hose connector. Insert the hose firmly and the click sound is heard.
If you use the washing machine more than once a week, there is no need to remove the inlet hose connector to avoid damaging the fixing screw.

8
Put the needed washing powder in the detergent box and softener in the softener box evenly

Control panel / Display

Plug the machine in and then press this key, the machine will turn on. Press this key again, it will turn off.
Press this key after turning on, the selected program will start. Press this key again, the operation will pause. Press it once again, the operation will resume.
Press to select the program. You can select the program from below according to the kind of your laundries.
Normal Wash normally soiled everyday clothing.
Speedy Wash speedy for not-so-dirty clothing.

Eco

Wash daily clothing with saving electricity and water.

Jeans Wash sturdy and heavy soiled clothing.

Air Dry

Program for reducing the time to dry. After spinning, blow air to clothing in the tub to reduce the time to dry in the shade greatly.

Blanket Wash strongly for blankets or heavy clothing.

Soft Baby

Wash not-so-dirty clothing or a small amount of clothing. Wash gently and rinse thoroughly for baby clothing.

Delicate Wash clothing with the HAND WASH mark.

Tub

Clean washing / spin drying tub. (See “Tub clean”.)

Control panel / Display
When turning on the machine, the digital timer shows “–” . If select “Air Dry” program, the digital timer displays the air dry time, unit is MIN. When washing, the digital timer shows the remaining operation time, unit is MIN or Hour. When the preset time is set, the digital timer shows the preset time, unit is HOUR. When the trouble occurs, the digital time shows the trouble code.
Press to set the preset time. You can select the time from 2-24 hours. Press to select the water level or add water in the tub during wash. (See “Add water”.)
Displays the water level.

INLET WATER

Blinks during water supply.
Displayed for the remaining operation time.
Displayed while setting the preset time or until the preset time comes. You can see the details of preset program by touching until the preset time comes.
Displayed when child lock is set. (See “Child lock”.)
Press to select the spinning time. (9 min. / 7 min. / blank / 5 min. / 3 min. / Soft spin ) Default setting depends on each program. When selecting “Air Dry” program, you can also change the time to dry by pressing this key. (30 min. / 60 min. / 90 min. Default setting: 30 min.)
Press to select the rinse times. (4 times / 3 times / 2 times / blank / 1 time) Default setting depends on each program.
Press to select the washing time. (20 min. / 15 min. / blank / 12 min. / 9 min. ) Default setting depends on each program. You can turn on/off the soak function by pressing this button for 2 seconds. (See “Soak function”.)

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>