CARKIDS 4310036 I Size Darcy Car Seat 360 Degree Rotatable Instruction Manual
- June 16, 2024
- CARKIDS
Table of Contents
AUTOSTOEL 360°
4310036
4310037
INSTRUCTIONS MANUAL
I-SIZE ISO-FIX
40-150CM R129
0313992
UN Regulation No. 129/03
lnstalling in rearward facing with 5 point harness :40-105cm
Notice
NOT TO USE REARWARD FACING ECRS (ECRS = Enhanced Child Restraint System) IN
SEATING POSITIONS WHERE THERE IS AN ACTIVE FRONTAL AIRBAG INSTALLED. IMPORTANT
– DO NOT USE FORWARD FACING BEFORE THE CHILD’S AGE EXCEEDS 15 MONTHS (Refer to
instructions).
Notice regarding i-Size category Enhanced Child Restraint Systems(40-105cm).
This is an i-Size Enhanced Child Restraint System.
Il is approved according to UN Regulation No.129/03, for use in, i-Size
compatible vehicle sealing positions as indicated by vehicle manufacturers in
the vehicle user’s manual.
lf in doubt, consult either the Enhanced Child Restraint System manufacturer
or the retailer.
Notice regarding i-Size booster seat category Enhanced Child Restraint Systems
(100-150cm).
This is i-Size booster seat Enhanced Child Restraint System.
Il is approved according to UN Regulation No.129, for use primarily in “i-Size
sealing positions” as indicated by vehicle manufacturers in the vehicle user’s
manual.
lf in doubt, consult either the Enhanced ChiId Restraint System manufacturer
or the retailer.
Questions
Contact your supplier if you wish to make a warranty claim or have any other
questions.
Your car seat can be fixed safely on almost seats of the cars. However, on
some seats the belts are fixed so that proper installation is not possible, in
that case, try another seat.
Use in the vehicle
You can use your child car seat as follows:
Do not Use with 2-point belt.
Please install with the 3-point belt.
Please observe the regulations applicable to your
particular country.
The safety belt must be approved to ECE R 16 or a comparable standard.
Do not use with 2-point belt.
Can be used if the vehicle seat is equipped with a 3-point belt.
Use in the vehicle
| In the direction of travel. | Yes |
|---|---|
| Against the direction of travel. | Yes |
| With 2-point belt | **** No |
The use of a 2-point belt substantially increases the risk of injury to your
child in the event of an accident.|
With 3-point belt| Yes
The safety belt must be approved to ECE R 16 or a comparable standard (see
test label on belt with an “E” or “e” in a circle).|
with the ISOFIX and Top Tether anchoring systems
If there is a front airbag: Slide the passenger seat along way back and refer
to any instructions in vehicle owner’s manual.|
On front passenger seat| Yes
Do not use on passenger seats with a front airbag! The front passenger seat
may be used with or without ISOFIX, with the same notes as currently given for
the ISOFIX(slide the seat back and refer to vehicle instructions).|
On outer rear seat| Yes
On center rear seat| **** Yes
Can be used if the vehicle seat is equipped with a 3-point belt
(Please observe the regulations applicable to your particular country)
The seat has two installation methods, the following table shows the
installation types for each group:
Tested and approved according to ECE R129/03
I-size| Body size| lnstallation method| lnstallation direction
40-105cm<18kg| lsofix+top-tether| rearward facing
76-105cm<18kg| lsofix+top-tether| forward facing
I-size Booster Seat| 100-150cm| lsofix attachments+ adult safety-belt| forward
facing
Car Seat Components
Car Seat Components
- Headrest
- Red Belt Guide Hook
- Fabric Cover
- Shoulder Pad
- Cushion
- Buckle
- Crotch Pad
- Adjusting Device
- Harness Adjustment Strap
- Headrest Handle
- Harness
- Backrest Reclining Handle
- Backrest Rotating Handle
- Base
- Backrest Hanger
- L-Backrest locker
- L-Backrest
- Top Tether
- Backrest
- ISOFIX Button
- ISOFIX Connector
Care and Maintenance
4.1 How to use the harness buckle
4.1.1 Guide the two buckle latches together.
4.1.2 Make sure right side up.
4.1.3 Engage them before putting them into the harness buckle, this should
make a CLICK noise.
4.1.4 Pull shoulder belts to remove all slack from the lap section ensuring
the harness lies flat and harness buckle locked. Open the harness buckle by
pressing the red button.
4.2 Care for the harness buckle
It is vital for the safety of your child that the harness buckle works
correctly.
Malfunctions of the harness buckle are usually caused by accumulations of dirt
or foreign bodies.
Malfunctions are as follows:
- The buckle latches are ejected only slowly when the red release button is pressed.
- The buckle latches will no longer lock home (i.e. they are ejected again if you try to push them in).
- The buckle latches engage without an audible CLICK
- The buckle latches are difficult to insert (you feel resistance).
- The buckle only opens if extreme force is applied.
4.3 Remedy
Wash out the harness buckle so that it functions properly once again.
4.4 Removing 5-point harness
4.4.1 Loosen the 5-point harness of the child seat as much as possible by
press the button of the crotch belt.
4.4.2 Turn the baby safety car seat to back, unzip the seat cover.
4.4.3 Loosening the shoulder belt in order to access the metal link and
connector at the back of the child seat, remove the belt from connector, then
remove the shoulder belt from metal link.
4.4.4 Then from the front of the child seat, pull out shoulder belt through
the slots.
4.4.5 Pull below both, the shoulder pads and the belts to the front through
the slots. (front side of the child seat).
4.4.6 Remove the shoulder pads from the shoulder belts and put them in the
storage bag.
4.4.7 Roll the shoulder belts separately on both side and place them into the
fabric cover from the slot of fabric.
4.4.8 Grasp the metal plate from underneath and turn it into a vertical
position. Push upwards and slide the metal plate through the slot.
4.4.9 Remove the harness buckle with the crotch pad and store it in the
storage bag.
4.5 Cleaning the harness buckle
4.5.1 Open the harness buckle (press the red button).
4.5.2 Grasp the metal plate from underneath and turn it into a vertical
position.
4.5.3 Slide the metal plate through the slot.
4.5.4 Remove the harness buckle.
4.5.5 Soak the harness buckle in warm water with washing-up liquid for at
least an hour. Then rinse and dry it thoroughly.
4.6 Adjust the angle of child safety car seat
There are 3 levels adjustment in the child safety car seat. Before fixing a
child in the child restraint system, the seat must be set on the recline
position for rear-facing use,see picture ③ or in the sitting position for
forward-facing use, see picture①②
To achieve that, use the recline handle located in front of the child
restraint system between the sitting part and the base to adjust the desired
position.
Total has two level positions:
- first level
- second level
Use backrest reclining handle to adjust the postion 1,2 when forward facing installation.
Adjust the reclining angle to position 2 first, then release the L-Backrest
locker, use backrest rotating handle to swivel the seat 180º for rearward
facing installation.
4.7 Adjust the length of harness
In order to protect your child much better,after fix him/her in the child
restraint system and lock the buckle, you should tighten the harness so they
are snug and flat against the child’s body,they should never be twisted or
loose.
4.7.1 To tighter the harness,pull the shoulder belt upwards to remove the
slack from the lap sections of the harness,at the same time to pull the
adjuster crotch belt coming from the lock by your another hand.
4.7.2 To lengthen the harness, press the button on lock between the child’s
two leg,then pull the two shoulder belt simultaneously in yourdirection,
please note while you are doing this hold the harness, not the harness cover.
CAUTION! Check that the harness straps are not twisted and that they have
been correctly inserted in the belt slots on the cover.
4.8 Adjusting the headrest in an installation with a 5 point
harness.40-105cm
4.8.1 A correctly adjusted harness ensures that the diagonal seat belt section
is positioned, and gives your child the optimal protection.
4.8.2 The harness must be adjusted to that there is a space two fingers wide
between the harness and your child’s body.
4.8.3 A Correctly adjusted headrest ensures optimal protection for your child
in the safety seat: shoulder belts are at the same level as your child’s
shoulders.
4.8.4 Pull the headrest handle, the shoulder straps will be moved together, select correct height and fix them in the correct position for the child by releasing the headrest handle.
4.9 Adjusting the headrest in an installation that uses the vehicle safety
belt. 40-105cm
4.9.1 A correctly adjusted headrest ensures that the diagonal seat belt
section is opti- mally positioned, and gives your child the optimal
protection.
4.9.2 The headrest must be adjusted so that a space equivalent to two fingers
remains between the headrest and the child’s shoulders.
4.9.3 Pull the headrest handle to adjust headrest to the correct height, then
release the headrest handle.Place the safety seat on the car seat,put the
child in the seat and check the height.
4.9.4 Repeat the process until the correct height is achieved.
Installation
5.1 40-105cm Install Rearward Facing
5.1.1 Check the safety seat is ready to be installed rearward facing pull the
backrest reclining handle to recline the seat fully, adjust the angle of
recline to position 2, then release the handle.
5.1.2 It is necessary swivel the seat 180º to place the seat in the opposite
direction of travel. Release the backrest rotating handle when the seat is in
the desired position.
5.1.3 Locate the ISOFIX arms in the base of the seat.
5.1.4 Place the seat in the back seat of the vehicle in the opposite direction
of travel.
5.1.5 Hold the safety seat with both hands and insert the two ISOFIX arms
firmly into the vehicle’s ISOFIX anchoring points until they fasten with a
click on both sides.
The red button will change to green on both sides.
5.1.6 Shake the seat to check that it is correctly anchored to the vehicle’s
ISOFIX points.
5.1.7 Pull out the Top Tether and press the tether strap release button to
extend the strap until it is long enough to connect it to the Top Tether
anchorage point in the vehicle. If the Top Tether is tightened favorably and
correctly, the button will change to green.
5.1.8 Make sure the 5-point harness of safety seat has been correctly
installed (see section 4.1)
5.1.9 Open the buckle, put the shoulder harness to the sides, then put the
child into the safety seat. Please check if shoulder harness height is equal
to your child’s shoulder height, press the adjusting device and pull the
shoulder harness to be loose, then press the headrest handle to adjust the
shoulder harness to the suitable position.
5.1.10 Slide the two tongues together into the buckle. The buckle will not
work well till you hear “click”. Adjust the child restraint belt to make sure
the lap belt is well restrained the child’s pelvis. Then tighten the shoulder
straps by pulling the adjustable strap at the front of the bottom cushion.
5.1.11 If you want to release your child from the safety seat, press the
adjusting device at the front of the bottom, at the same time pull the
shoulder straps. Then press the red button on the buckle, place the shoulder
straps at the side and let your child out.
5.1.12 The insertion guides facilitate the installation of the safety seat
with the aid of the ISOFIX securing points and prevents damage to the
upholstery. When not in use they should be removed and stored in a safe place.
In vehicles with a reclining back the insertion guides should be removed
before the seat is reclined. Problems that may arise are generally the result
of accumulation of dirt or foreign bodies in the insertion guides and the
clasps. To solve this type of problem simply clean the part in question.
Uninstalling the ISOFIX system
- To free the Top Tether, press the button and pull the tether strap in the opposite direction(the indicator will change from green to red color), in order to take off the top tether.
- To free the lSOFIX anchoring, press backwards the ISOFIX System unlock buttons (the indicator will change from green to red color), in order to free the seat from the vehicle ISOFIX anchoring system.
5.2 76-105cm Install Forward Facing
5.2.1 Ensure L-Backrest locker is locked with Backrest Hanger, the seat is
ready to install in forward facing, pull the backrest reclining handle to
adjust to angle to any position 1 or 2, then release the handle.
5.2.2 It is necessary swivel the seat 180º to place the seat in the direction
of travel. Release the backrest rotating handle when the seat is in the
desired position.
5.2.3 Locate the lSOFIX arms in the base of the seat.
5.2.4 Place the child safety seat in the back seat of the vehicle facing in
the direction of travel.
5.2.5 Hold the child seat with both hands and insert the two ISOFIX arms
firmly into the vehicle’s ISOFIX anchoring points until they fasten with a
click on both sides.
The red button will change to green on both sides .
5.2.6 Shake the seat to check that it is correctly anchored to the vehicle’s
ISOFIX points.
5.2.7 Pull out the Top Tether and press the tether strap release button to
extend the strap until it is long enough to connect it to the Top Tether
anchorage point in the vehicle. If the Top Tether is tightened favorably and
correctly, the button will change to green.
5.2.8 Make sure the 5-point harness of safety seat has been correctly
installed (see section 4.1)
5.2.9 Open the buckle, put the shoulder harness to the sides, then put the
child into the safety seat. Please check if shoulder harness height is equal
to your child’s shoulder height, press the adjusting device and pull the
shoulder harness to be loose, then press the headrest handle to adjust the
shoulder harness to the suitable position.
5.2.10 Slide the two tongues together into the buckle. The buckle will not
work well till you hear “click”. Adjust the child restraint belt to make sure
the lap belt is well restrained the child’s pelvis. Then tighten the shoulder
straps by pulling the adjustable strap at the front of the bottom cushion.
5.2.11 If you want to release your child from the safety seat, press the
adjusting device at the front of the bottom, at the same time pull the
shoulder straps. Then press the red button on the buckle, place the shoulder
straps at the side and let your child out.
5.2.12 The insertion guides facilitate the installation of the safety seat
with the aid of the ISOFIX securing points and prevents damage to the
upholstery. When not in use they should be removed and stored in a safe place.
In vehicles with a reclining back the insertion guides should be removed
before the seat is reclined. Problems that may arise are generally the result
of accumulation of dirt or foreign bodies in the insertion guides and the
clasps. To solve this type of problem simply clean the part in question.
Note: Use backrest rotating handle to swivel the seat 180º for forward facing installation, backrest hanger and L-backrest hanger are hooked each other.
Uninstalling the ISOFIX system
- To free the Top Tether, press the button and pull the tether strap in the opposite direction(the indicator will change from green to red color), in order to take off the top tether.
- To free the lSOFIX anchoring, press backwards the ISOFIX System unlock buttons (the indicator will change f rom green to red color), in order to free the seat from the vehi- cle ISOFIX anchoring system.
5.3 100-150cm Install Forward Facing
5.3.1 Ensure that the child seat’s 5-point harness and buckle is removed
correctly (see 4.4)
5.3.2 Ensure the seat is ready to install in forward facing, pull the backrest
reclining handle to adjust to angle to any position 1or 2, then release the
handle.
5.3.3 It is necessary swivel the seat 180º to place the seat in the direction
of travel.
Release the backrest rotating handle when the seat is in the desired position.
5.3.4 Before installing the safety seat, place your child in the seat and
adjust the headrest to the correct height(see 4.9)
5.3.5 Place the child safety seat in the back seat of the vehicle facing in
the direction of travel
5.3.6 Hold the child seat with both hands and insert the two ISOFIX arms
firmly into the vehicle’s ISOFIX anchoring points until they fasten with a
click on both sides.
The red button will change to green on both sides .
5.3.7 Shake the seat to check that it is correctly anchored to the vehicle’s
ISOFIX points.
5.3.8 Place your child in the safety seat.
5.3.9 Pass the vehicle seat belt through the bottom of the armrest, ensure the
lap belt is stretched as low as possible over the child’s hips, buckle the
vehicle seat belt until hear a click. Place the diagonal belt through red belt
guide hook and must pass the middle between child’s shoulder and neck.
5.3.10 The insertion guides facilitate the installation of the safety seat
with the aid of the ISOFIX securing points and prevents damage to the
upholstery. When not in use they should be removed and stored in a safe place.
In vehicles with a reclining back the insertion guides should be removed
before the seat is reclined. Problems that may arise are generally the result
of accumulation of dirt or foreign bodies in the insertion guides and the
clasps. To solve this type of problem simply clean the part in question.
Note: Use backrest rotating handle to swivel the seat 180º for forward facing installation, backrest hanger and L-backrest hanger are hooked each other.
Uninstalling the ISOFIX system
To free the lSOFIX anchoring, press backwards the ISOFIX System unlock buttons
(the indicator will change from green to red color), in order to free the seat
from the vehicle ISOFIX anchoring system.
Removal fabric cover and assembly
6.1 Removal
Cleaning
Please be sure to use only original seat covers, as the seat cover is
important to the proper functioning of the system.
**** The child seat must not be used without the seat cover.
7.1 The cover can be removed and washed with a mild detergent using the
washing machine’s cycle for delicate items (30C). Please observe the
instructions on the washing label of the cover. The colours of the cover may
fade if washed at more than 30C. Do not spin, and never tumble dry in an
electric clothes dryer (the fabric may separate from the padding).
7.2 The plastic parts can be cleaned using soapy water. Do not use harsh
cleaning agents (such as solvents).
7.3 The harness can be removed and washed in lukewarm soapy water Caution!
Never remove the buckle tongues from the straps.
Checklist
For safety’s sake read through this checklist before you set off. Check that
the harness belt system fits properly and tightly around your child and that
the shoulder belts are at the correct height. Check regularly that the belt in
the baby car seat is not damaged. If it is damaged do not use your product in
any circumstances and contact your supplier or importer (see address list in
the service card).Check that you have secured your baby car seat with the seat
belt. If you have any questions, please contact your supplier.
8.1 Make sure that you have the following details to hand:
8.2 Serial number underneath on the service card.
8.3 Mark and type of vehicle and seat on which the baby car seat used.
Age and length of your child.
HANDLEIDING
NEDERLANDS
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>