SHARP SMO1759JS Over the Range Microwave Oven Instruction Manual

Over-the-Range Microwave Oven:
INSTALLATION MANUAL
SMO1759JS Installation Instructions

IMPORTANT SAFETY INSTRUCTIONS

This product requires a three-prong grounded outlet. The installer must perform a ground continuity check on the power outlet box before beginning the installation to ensure that the outlet box is properly grounded. If not properly grounded, or if the outlet
box does not meet electrical requirements noted (under ELECTRICAL REQUIREMENTS), a qualified electrician should be employed to correct any deficiencies. CAUTION: For personal safety, remove house fuse or open circuit breaker before beginning installation to avoid severe or fatal shock injury.
CAUTION: For personal safety, the mounting surface must be capable of supporting the cabinet load, in addition to the added weight of this 63–85 pound (28.5–38.5 kg) product, plus additional oven loads of up to 50 pounds (22.7 kg) or a total weight of 113–135 pounds (51.3–61.2 kg).
CAUTION: For personal safety, this product cannot be installed in cabinet arrangements such as an island or a peninsula. It must be mounted to BOTH a top cabinet AND a wall.
NOTE: For easier installation and personal safety, it is recommended that two people install this product.
IMPORTANT – PLEASE READ CAREFULLY. FOR PERSONAL SAFETY, THIS APPLIANCE MUST BE PROPERLY GROUNDED TO AVOID SEVERE OR FATAL SHOCK.You should have the wall receptacle and circuit checked by a qualified electrician to make sure the receptacle is properly grounded.
Where a standard two-prong wall receptacle is encountered, it is very important to have it replaced with a properly grounded three-prong wall receptacle, installed by a qualified electrician.
DO NOT, UNDER ANY CIRCUMSTANCES, CUT, DEFORM OR REMOVE ANY OF THE PRONGS FROM THE POWER CORD. DO NOT USE WITH AN EXTENSION CORD.

ELECTRICAL REQUIREMENTS

Product rating is 120 volts AC, 60 Hertz, 15 amps and 1.6 kilowatts. This product must be connected to a The power supply cord and plug should be brought to a the prevailing local code for this kilowatt rating.
the requirements of the National Electrical Code or voltage and frequency. Wire size must conform to seperate and dedicated supply circuit of the proper seperate and dedicated 20 ampere branch be located in the cabinet above the microwave oven.
circuit single grounded outlet. The outlet box should The outlet box and supply circuit should be installed by a qualifed electrician and conform to the National Electrical Code or the prevailing local code.

DAMAGE—SHIPMENT INSTALLATION

• If the unit is damaged in shipment, return the unit to the store in which it was bought for repair or replacement.
• If the unit is damaged by the customer, repair or replacement is the responsibility of the customer.
• If the unit is damaged by the installer (if other than the customer), repair or replacement must be made by arrangement between customer and installer.

PARTS INCLUDED

HARDWARE PACKET (9KL12970000000429)

PART|

QUANTITY

---|---
| Wood Screws (1⁄4“ x2“)| 2
| Toggle Bolts (and wingnuts) (3⁄16“ x3“)| 2
| Self-Aligning Machine Screws (1⁄4“-28×31⁄4“)| 3
| NylonGrommet (formetal cabinets)| 1

You will find the installation hardware contained in a packet with the unit. Check to make sure you have all these parts.
NOTE: Some extra parts are included.

PART|

QUANTITY

---|---
| TopCabinet Template| 1
| Rear Wall Template| 1
| Installation Instructions| 1
Use & Care Manual| 1
| Separately Packed Grease Filters| 2
| Exhaust Adapter| 1
| Glass Tray| ****

1

| Turuntable Ring| 1
| CHARCOAL FILTER| 1

TOOLS YOU WILL NEED

MOUNTING SPACE

PLACEMENT OF THE MOUNTING PLATE

A. REMOVING THE MICROWAVE OVEN FROM THE CARTON/ REMOVING THE MOUNTING PLATE

1. Remove the top cover board, installation instructions, use and care, exhaust adapter, turntable ring, shelf, filters, glass tray and the Do not remove the Styrofoam protecting the front of the oven. bag. small hardware
2. Fold back all 4 carton flaps fully against carton sides. Then carefully roll the oven and carton over onto the top side. The oven should be resting in the Styrofoam.
3. Pull the carton up and off the oven.
4. Cut the middle of the outer protective plastic bag to remove the ounting latem
5. Remove the screws from each end of the mountingplate. This plate will be used as the rear wall templateand for mounting. Reinstall the screws into the holeswhere they were removed.

FINDING THE WALL STUDS

1. Find the studs, using one of the following methods:
   A. Stud finder – a magnetic device which locates nails.
   B. Use a hammer to tap lightly across the mounting surface to find a solid sound.
   This will indicate a stud location.

2. After locating the stud(s), find the center by probing the wall with a small nail to find the edges of the stud. Then place a mark halfway between the edges. The center of any adjacent studs should be 16 (40.6 cm) or 24 (61 cm) from this mark.

3. Draw a line down the center of the studs.

THE MICROWAVE MUST BE CONNECTED TO AT LEAST ONE WALL STUD.

C. DETERMINING WALL PLATE LOCATION UNDER YOUR CABINET

Plate position bottom with front overhang -beneath recessed cabinet

Your cabinets may have decorative trim that interferes with the microwave installation. Remove the decorative trim to install the microwave properly and to make it level.
THE MICROWAVE MUST BE LEVEL.
Use a level to make sure the cabinet bottom is level.
If the cabinets have a front overhang only, with no back or side frame, install the mounting plate down the same distance as the front overhang depth. This will keep the microwave level.

1. Measure the inside depth of the front overhang.
2. Draw a horizontal line on the back wall an equal distance below the cabinet bottom as the inside depth of the front overhang.
3. For this type of installation with front overhang only, align the rear template with this horizontal line, not touching the cabinet bottom as described in Step D.

D. ALIGNING THE WALL PLATE![SHARP SMO1759JS Over the Range Microwave Oven

• DETERMINING WALL 2](https://manuals.plus/wp-content/uploads/2024/01/SHARP- SMO1759JS-Over-the-Range-Microwave-Oven-DETERMINING-WALL-2.jpg)

CAUTION: Wear gloves to avoid cutting fingers on sharp edges.

1. Draw a vertical line on the wall at the center of the 30″ wide space.
2. Draw a horizontal line on the wall at the bottom of “Rear Wall Template”.
3. Find a wall stud in area “D” of mounting plate Refer to section 1B. Finding the wall studs.
4. For attaching the mounting plate into stud drill a 3/16″ hole into wood stud. Drill a 5/8″ hole for toggle bolt in 2 other locations at or as close to both hole A and B as possible.
   NOTE: DO NOT MOUNT THE PLATE AT THIS TIME.
   NOTE: If Holes A and B are not in a stud, find a stud somewhere For proper installation, holes A and B should be used. important to have at least one wood screw mounted firmly in a stud to support the weight of the microwave. Set the mounting plate aside.

INSTALLATION TYPES

(Choose A, B or C)

This microwave oven is designed for adaptation to the following three types of ventilation:
A. Outside Top Exhaust (Vertical Duct)
B. Outside Back Exhaust (Horizontal Duct)
C. Recirculating (Non-Vented Ductless)|
NOTE: This microwave is shipped assembled for Recirculating. Select the type of ventilation required for your installation and proceed to that section.

A. OUTSIDE TOP EXHAUST (VERTICAL DUCT)

B. OUTSIDE BACK EXHAUST (HORIZONTAL DUCT)

C . RECIRCULATING (NON-VENTED DUCTLESS)Models are shipped for recirculating exhaust.
These models have a disposable charcoal filter installed to help remove smoke and odors.
NOTE: Read the next two pages only if you plan to vent your exhaust to the outside. If you plan to recirculate the air back into the room, proceed to page 20.

INSTALLATION INSTRUCTIONS FOR EXTERNAL EXHAUST DUCTING

NOTE: If you need to install ducts, note that the total duct length of 31 ⁄4” x 10” (8.2 x 25.4 cm) rectangular or ” (15.2 cm) diameter round duct Outside ventilation requires an EXTERNAL EXHAUST
NOTE: It is important that venting be installed using the most direct route and with as few elbows as possible.
This ensures clear venting of exhaust and helps prevent blockages. Also, make sure dampers swing freely and nothing is blocking the ducts.
Exhaust connection:
The exhaust adaptor has been designed to mate with a standard 3 ⁄4” x 10” (8.2 x 25.4 cm) rectangular duct.
If a round duct is required, a rectangular-to-round 1(12.5” should not exceed 120 equivalent feet (36.5 m).7 cm)
DUCT.Read the following carefully. diameter/ 6 transition adaptor must be used. diameter duct is acceptable to use.” A 5 (12.7cm)/ 6″ (15.2cm) ”
Maximum duct length:
For satisfactory air movement, the total duct length of 3 (12.5” 1 ⁄4” x 10” (8.2 x 25.4 cm) rectangular or 6 ”(15.2 cm) diameter/ 7 cm) diameter round duct should not exceed 120 equivalent feet (36.5 m).
Elbows, transitions, wall and roof caps, etc., present additional resistance to airflow and are equivalent to a section of straight duct which is longer than their actual physical size. When calculating the total duct length, add the equivalent lengths of all transitions and adaptors plus the length of all straight duct sections.  The chart below shows you how to calculate total equivalent ductwork length using the approximate feet of equivalent length of some typical ducts.

DUCT PIECES| EQUIVALENT LENGTH| x| NUMBER USED| =| EQUIVALENT LENGTH
---|---|---|---|---|---
*| Rectangular-to-Round TransitionAdaptor| 5Ft. (1.5m)| x| ( )| =| Ft. orm
**| Wall Cap| 40Ft. (12.2m)| x| ( )| =| Ft. orm
| 90° Elbow| 10Ft. (3m)| x| ( )| =| Ft. orm
| 45° Elbow| 5Ft. (1.5m)| x| ( )| =| Ft. orm
| 90° Elbow| 25Ft. (7.6m)| x| ( )| =| Ft. orm
| 45° Elbow| 5Ft. (1.5m)| x| ( )| =| Ft. orm

| RoofCap| 24Ft. (7.3m)| x| ( )| =| Ft. orm
| StraightDuct6“ (15.2cm) Roundor31⁄4“ x10“ (8.2×25.4cmRectangular)| 1Ft. (0.3m)| x| ( )| =| Ft. orm
| | | Total Ductwork| =| Ft. or m

• IMPORTANT: If a rectangular-to-round transition adaptor is used, the bottom corners of the damper will have to be cut to fit, using the tin snips, in order to allow free movement of the damper.
  Equivalent lengths of duct pieces are based on actual tests and reflect requirements for good venting performance with any vent hood.

EXTERNAL EXHAUST DUCTING
OUTSIDE TOP EXHAUST (EXAMPLE ONLY)
The following chart describes an example of one possible ductwork installation.

12 Ft. (3.6 m)
| Rectangular-to-Round Transition Adaptor*| 5 Ft. (1.5 m) x| (1)| =| 5 Ft. (1.5 m)
Equivalent lengths of duct pieces are based on actual tests and reflect requirements for good venting performance with any vent hood.| =| 41 Ft. (12.4 m)

• IMPORTANT: If a rectangular-to-round transition adaptor is used, the bottom corners of the damper will have to be cut to fit, using the tin snips, in order to allow free movement of the damper.

OUTSIDE BACK EXHAUST (EXAMPLE ONLY)
The following chart describes an example of one possible ductwork installation.

DUCT PIECES| EQUIVALENT **LENGTH*| x| NUMBER USED| =| EQUIVALENT LENGTH
---|---|---|---|---|---
| Wall Cap| 40Ft. (12.2m)| x| (1)| =| 40Ft. (12.2m)
**| 3Ft. StraightDuct (31⁄4” x10”/8.2×25.4cm
Rectangular)| 3Ft. (0.9m)| x| (1)| =| 3Ft. (0.9m)
****| 90° Elbow| 10Ft. (3m)| x| (2)| =| 20Ft. (6 m)
Equivalent lengths of duct pieces are based on actual tests and reflect requirements for good venting performance with any vent hood.| Total Length| =| 63 Ft. (19.1 m)

NOTE: For back exhaust, care should be taken to align exhaust with space between studs, or wall should be prepared at the time it is constructed by leaving enough space between the wall studs to accommodate exhaust.

A. OUTSIDE TOP EXHAUST (Vertical Duct)

INSTALLATION OVERVIEW
A1. Attach Mounting Plate to Wall
A2. Prepare Top Cabinet
A3. Adapting Microwave Blower for Outside Top Exhaust
A4. Check Damper Operation
A5. Mount Microwave Oven
A6. Adjust Exhaust Adaptor
A7. Connect Ductwork

IMPORTANT NOTES:

• Make sure the screws for the blower motor and blower plate are securely tightened when they are reinstalled. This will help to prevent excessive vibration.
• Make sure the motor wiring has been properly routed and secured, and that the wires are not pinched.

A1. ATTACH THE MOUNTING PLATE TO THE WALL

Attach the plate to the wall using toggle bolts.
At least one wood screw must be used to attach the plate to a wall stud.

1. Remove the toggle wings from the bolts.

2. Insert the bolts into the mounting plate through the holes designated to go into drywall and reattach the toggle wings to each bolt. 3⁄4″ (19 mm) ontoTo use toggle bolts:
   To use toggle bolts:
   

3. Place the mounting plate against the wall and insert the toggle wings into the holes in the wall to mount the plate.
   NOTE: Before tightening toggle bolts and wood screw, make sure the bottom of the mounting plate centered under the cabinet. touch the bottom of the Rear wall template when pushed flush against the wall and that the plate is properly
   CAUTION: Be careful to avoid pinching fingers between the back of the mounting plate and the wall.

4. Tighten all bolts. Pull the plate away from the wall to help tighten the bolts.

A2. USE TOP CABINET TEMPLATE FOR PREPARATION OF TOP CABINET
You need to drill holes for the top support screws, a hole large enough for the power cord to fit through, and a cutout large enough for the exhaust adaptor.

• Read the instructions on the TOP CABINET TEMPLATE.
• Tape it underneath the top cabinet.
• Drill the holes, following the instructions on the TOP CABINET TEMPLATE.
  CAUTION: Wear safety goggles when drilling holes in the cabinet bottom.

A3. ADAPTING MICROWAVE BLOWER FOR OUTSIDE TOP EXHAUST

1. Place the microwave in its upright position,with the top of the unit facing up.Remove the screw that holds the blower plateto the microwave. Remove and save the screw holding the blower motor to the microwave.

2. Carefully pull out the blower unit. The wires will extend far enough to allow you to adjust the blower unit.

3. Roll the blower unit 90° so that fan blade openings are facing out the top of the microwave.

4. Place the blower unit back into the opening. CAUTION: Do not pull or stretch the blower unit wiring. Make sure the wires are not pinched, and that they are properly secured.
   A3. ADAPTING MICROWAVE BLOWER FOR OUTSIDE TOP EXHAUST

5. Secure blower unit to microwave with the screw removed in Step 1. Make sure the screw is tight.

6. Replace blower plate with the screws removed in Step 1. Make sure the screws are tight.Attach the exhaust adaptor to the top of theblower plate by sliding it into the guides of the blower plate.Push in securely until it is in the locking tabs.
   Take care to assure that the damper hinge is installed so that the damper swings freely.

A4. CHECK FOR PROPER DAMPER OPERATION

• Make sure tape securing damper is removed and damper pivots easily before mounting microwave.
• You will need to make adjustments to assure proper alignment with your house exhaust duct after the microwave is installed.

A5. MOUNT THE MICROWAVE OVEN

FOR EASIER INSTALLATION AND PERSONAL SAFETY, WE RECOMMEND THAT TWO PEOPLE INSTALL THIS MICROWAVE OVEN.
IMPORTANT: Do not grip or use the handle or heat shield during installation. Do not remove the cardboard spacers between the heat shield and door.
NOTE: If your cabinet is metal, use the nylon grommet around the power cord hole to prevent cutting of the cord.
NOTE: We recommend using filler blocks if the cabinet front hangs below the cabinet bottom shelf.
IMPORTANT: If filler blocks are not used, case damage may occur from overtightening screws.
NOTE: When mounting the microwave oven, thread power cord through hole in bottom of top cabinet. Keep it tight throughout Steps 1–3. Do not pinch cord or lift oven by pulling cord.

1. Lift microwave, tilt it forward, and hook slots at back bottom edge onto four lower tabs of mounting plate.

2. Rotate front of ovenup against cabinet bottom.

3. Insert a self-aligning screw through one of the top cabinet holes.
   Temporarily secure the oven by turning the screw at least two full turns after the threads have engaged. (It will be completely tightened later.) Be sure to keep power cord tight. Be careful not to pinch the cord, especially when mounting flush to bottom of cabinet.
   A5. MOUNT THE MICROWAVE OVEN (cont.)

4. Attach the microwave oven to the top cabinet.

5. Insert 2nd self aligning screw through remaining top cabinet hole.
   Turn two full turns on screw.

6. Tighten the outer two screws to the top of themicrowave oven. (While tightening screws, hold the microwave oven in place against the wall and the top cabinet.)

7. Install grease filters. See the Use &and Care packed with the microwave.

A6.ADJUST THE EXHAUST ADAPTOR
Open the top cabinet and adjust the exhaust adaptor to connect to the house duct.

A7. CONNECTING DUCTWORK

1. Extend the house duct down to connect to the exhaust adaptor.
2. Seal exhaust duct joints using duct tape for high temperature applications.

B OUTSIDE BACK EXHAUST (Horizontal Duct)

INSTALLATION OVERVIEW

B1. Prepare Rear Wall
B2. Remove Blower Plate
B3. Attach Mounting Plate to Wall
B4. Prepare Top Cabinet
B5. Adjust Blower
B6. Mount the Microwave Oven

IMPORTANT NOTES:

• Make sure the screws for the blower motor and blower plate  are securely tightened whenthey are reinstalled. This will help to prevent excessive vibration.
• Make sure the motor wiring has been properly routed and secured, and that the wires are not pinched.  

B1. PREPARING THE REAR WALL  FOR OUTSIDE BACK EXHAUST
You need to cut an opening in the rear wall for outside exhaust.

• Read the instructions on the REAR WALL TEMPLATE.
• Tape it to the rear wall.
• Cut the opening, following the instructions of the REAR WALL TEMPLATE.

B2. REMOVE BLOWER PLATE
Remove and save the screw that holds the blower plate to the microwave. Lift off the blower plate.

B3. ATTACH THE MOUNTING PLATE TO THE WALL

Attach the plate to the wall using toggle bolts.
At least one wood screw must be used to attach the plate to a wall stud.

1. Remove the toggle wings from the bolts.

2. Insert the bolts into the mounting plate through the holes designated to go into drywall and reattach the toggle wings to 3⁄4″ (19 mm) onto each bolt.
   To use toggle bolts:

3. Place the mounting plate against the wall andinsert the toggle wings into the holes in the wall to mount the plate.
   NOTE: Before tightening toggle bolts and wood screw, make sure the bottom of the mounting plate touch the bottom of the when pushed flush rear wall template against the wall and that the plate is properly centered under the cabinet.
   CAUTION: Be careful to avoid pinching fingers between the back of the mounting plate and the wall.

4. Tighten all bolts. Pull the plate away from the wall to help tighten the bolts.

B4. USE TOP CABINET TEMPLATE FOR PREPARATION OF TOP CABINET
You need to drill holes for the top support screws and a hole large enough for the power cord to fit through.![SHARP SMO1759JS Over the Range Microwave Oven

• Installation Instructions 15](https://manuals.plus/wp- content/uploads/2024/01/SHARP-SMO1759JS-Over-the-Range-Microwave-Oven- Installation-Instructions-15.jpg)

  • Read the instructions on the TOP CABINET TEMPLATE.
  • Tape it underneath the top cabinet.
  • Drill the holes, following the instructions on the TOP CABINET TEMPLATE.

CAUTION: Wear safety goggles when drilling holes in the cabinet bottom.

B5. ADAPTING MICROWAVE BLOWER FOR OUTSIDE BACK EXHAUST

1. Remove and save screw that holds blower motor to microwave.

2. Carefully pull out the blower unit. The wires will extend far enough to allow you to adjustthe blower unit.

3. Roll the blower unit 90°B5 .ADAPTING MICROWAVE BLOWER FOR OUTSIDE BACK EXHAUST (cont.)

4. Rotate blower unit counterclockwise 180°

5. Gently remove the wires from the grooves. Reroute the wires through grooves on other side of the blower unit.

6. Roll the blower unit 90° so that fan blade openings are facing out the back of the microwave.

7. Remove the knockout plates in the back of the unit with snips. (For some models) Knockout Plates: each knockout panel  Snip all 4 tabs on and remove the metal knockouts for rear airflow. Please take care to remove any sharp edges created from removing
   the knockout plates.

8. Place the blower unit back into the opening. CAUTION: Do not pull or stretch the blowerunit wiring. Make sure the wires are not pinched, and that they are properly secured.
   NOTE: The blower unit exhaust openings should match exhaust openings on rear of microwave oven.

9. Secure the blower unit to the microwave with the original screws.

10. Replace the blower plate in the same positionis tight. as before with the screws

11. Attach the exhaust adaptor to the rear of the oven by sliding it into the guides at the top center of the back of the oven.Push in securely until it is in the lower locking abs. Take care to assure that the damper hinge is installed so that it is at the top and that the damper swings freely.

B6. MOUNT THE MICROWAVE OVEN FOR EASIER INSTALLATION AND PERSONALSAFETY, WE RECOMMEND THAT TWO PEOPLE NSTALL THIS MICROWAVE OVEN.
IMPORTANT: Do not grip or use the handle or heat shield during installation. Do not remove the cardboard spacers between the heat shield and door.
NOTE: If your cabinet is metal, use the nylon grommet around the power cord hole to prevent cutting of the cord.
NOTE: We recommend using filler blocks if the cabinet front hangs below the cabinet bottom shelf.
IMPORTANT: If filler blocks are not used, case damage may occur from overtightening screws.
NOTE: When mounting the microwave oven, thread power cord through hole in bottom of top cabinet. Keep it tight throughout Steps 1–3. Do not pinch cord or lift oven by pulling cord.

1. Lift microwave, tilt it forward, and hook slots at back bottom edge onto four lower tabs of mounting plate.      

2. Rotate front of oven up against cabinet bottom.

3. Insert a self-aligning screw through one of the top cabinet holes.
   Temporarily secure the oven by turning the screw at least two full turns after the threads have engaged. (It will be completely tightened later.) Be sure to keep power cord tight. Be careful not to pinch the cord, especially when mounting flush to bottom of cabinet.

4. Attach the microwave oven to the top cabinet.

5. Insert 2nd self aligning screw through remaining top cabinet hole.
   Turn two full turns on screw.

6. Tighten the two screws to the top of the microwave oven. (While tightening screws, hold the microwave oven in place against the wall and the top cabinet.)

7. Install grease filters. See the Use &and Care packed with the microwave.

C . RECIRCULATING (Non-Vented Ductless)
C1. Attach Mounting Plate to Wall
C2. Prepare Top Cabinet
C3. Check Blower Plate
C4. Mount the Microwave Oven
C5. Install or change Charcoal Filter

C1. ATTACH THE MOUNTING PLATE TO THE WALL Attach the plate to the wall using toggle bolts.At least one wood screw must be used to attach the plate to a wall stud.
NOTE: If the cabinet depth including the cabinet doors is more than 13” then the unit must be spaced out from wall using adequate materials supporting 150 Ibs to allow proper top vent air exhaust/intake.

1. Remove the toggle wings from the bolts.

2.  Insert the bolts into the mounting plate through the holes designated to go into drywall and reattach the toggle wings to  3⁄4″ (19 mm) onto each bolt.
   To use toggle bolts:

3. Place the mounting plate against the wall and insert the toggle wings into the holes in the wall to mount the plate.
   NOTE: Before tightening toggle bolts and wood screw, make sure the bott m of the mounting plate centered under the cabinet.
   CAUTION: Be careful to avoid pinching fingers between the back of the mounting plate and the wall. touch the bottom of the Rear wall template when pushed flush against the wall and that the plate is properly

4. Tighten all bolts. Pull the plate away from the wall to help tighten the bolts.

C2. USE TOP CABINET TEMPLATE FOR PREPARATION OF TOP CABINET
You need to drill holes for the top support screws and a hole large enough for the power cord to fit through.![SHARP SMO1759JS Over the Range Microwave Oven

• CABINET](https://manuals.plus/wp-content/uploads/2024/01/SHARP-SMO1759JS- Over-the-Range-Microwave-Oven-CABINET.jpg)

  • Read the instructions on the TOP CABINET TEMPLATE.

  • Tape it underneath the top cabinet.
    NOTE: Adjust top template accordingly if the microwave is being spaced out from the wall due to cabinet depth (including cabinet doors) of more th n 13”. a

  • Drill the holes, following the instructions on the TOP CABINET TEMPLATE.
    CAUTION: Wear safety goggles when drilling holes in the cabinet bottom.
    C3.

C4. MOUNT THE MICROWAVE OVEN

FOR EASIER INSTALLATION AND PERSONAL SAFETY, WE RECOMMEND THAT TWO PEOPLE INSTALL THIS MICROWAVE OVEN.
IMPORTANT: Do not grip or use the handle or heat shield during installation. Do not remove the cardboard spacers between the heat shield and door.
NOTE: If your cabinet is metal, use the nylon grommet around the power cord hole to prevent cutting of the cord.
NOTE: We recommend using filler blocks if the cabinet front hangs below the cabinet bottom shelf. IMPORTANT: If filler blocks are not used, case damage may occur from overtightening screws.
NOTE: When mounting the microwave oven, thread power cord through hole in bottom of top cabinet. Keep it tight throughout Steps 1–3. Do not pinch cord or lift oven by pulling cord.

1. Lift microwave, tilt it forward, and hook slots at back bottom edge onto four lower tabs of mounting plate.

2. Rotate front of ovenup against cabinet bottom.

3. Insert a self-aligning screw through Temporarily secure the oven by cabinet holes. one of the top turning the screw at least two full turns after the threads have engaged. (It will be completely tightened later.) Be sure to keep power cord tight. Be careful not to pinch the cord, especially when mounting flush to bottom of cabinet.

4. Attach the microwave oven to the top cabinet.

5. Insert 2nd self aligning screw through remaining top cabinet hole.
   Turn two full turns on screw.

6. Tighten the two screws to the top of the microwave oven. (While tightening screws, holdthe microwave oven in place against the wall and the top cabinet.)

7. Install grease filters. See the Use &and Care packed with the microwave.

C5. INSTALLING OR CHANGE THE CHARCOAL FILTER (Some Models)
NOTE: The charcoal filter is factory installed in some models. Refer to the Use and Care to see if yours is factory installed and for replacement information.
For models without the recirculation filter access door,follow these steps to replace or install a charcoal filter.
Some models have a filter access door. Refer to the Use and Care to see if yours does.

1. Unplug microwave oven or disconnect power.
2. Open the microwave door and remove the two vent cover mounting screws located on top of the microwave using a #2 Phillips screwdriver. Remove the vent cover by pulling it out at the top and then pulling out.
3. Remove the charcoal filter by pushing the top of the filter inwards,then pull it forward out from the unit.
4. Slide the top of the new charcoal filter into thetop of the filter cavity.
5. Press the bottom of charcoal filter to place itinto the correct position.
6. Reinstall the vent cover by pushing the bottominto place. Push the vent top into position andhold in place. Replace the two vent cover mounting screws located on top of the microwave using a #2 Phillips screwdriver.
7. Close the microwave door. Plug in microwave oven or reconnect power.

BEFORE YOU USE YOUR MICROWAVE

1. Make sure the microwave oven has been installed according to instructions.
2. Remove all packing material from the microwave oven.
3. Install turntable ring and glas stray in cavity. , coupler,
4. Plug power cord into a seperate and dedicated 15- to 20-amp electrical outlet.
5. Replace house fuse or turn breaker back on.
6. Read the Manual.
7. KEEP INSTALLATION OR THE LOCAL INSPECTOR’S USE. Manual.

Operational check

1. Make sure the unit has been installed according to these instructions.
2. Remove all packing materials from the oven.
3. Replace house fuse or turn circuit breaker back on.
4. Plug power cord into receptacle .
5. Read operating instructions before testing the product.
6. Turn on the exhaust fan at high speed and confirm it is operating by using a tissue (it will stick to the filter)the outdoor exhaust flapper has opened.
7. For out side vented installations, confirm
8. Set the microwave oven for 1 minute and confirm the oven is operating normally using a cup of water.
9. Keep these ins tallation ins truction for the local electrical inspector’ s use.

NOTE: IT IS VERY IMPORTANT TO READ AND FOLLOW THE DIRECTIONS IN THE INSTALLATION INSTRUCTIONS BEFORE PROCEEDING WITH THIS REAR WALL TEMPLATE.
This Rear Wall Template serves to position the bottom mounting plate and to locate the horizontal exhaust outlet.

1. Use a level to check that the template is positioned accurately.

2. Locate and mark at least one stud on the left or right side of the centerline. It is important to use at least one wood screw mounted firmly in a stud to support the weight of the microwave. Mark two additional, evenly spaced locations for the supplied toggle bolts.

3. Drill holes in the marked locations. Where there is a stud, drill a 3/16″ hole for wood screws. For holes that do not line up with a stud, drill 5/8″ holes for toggle bolts.
   DO NOT INSTALL THE MOUNTING PLATE AT THIS TIME.

4. Remove the template from the rear wall.

5. Review the Installation Instruction book for your installation situation.

F. CUT OUT FOR HORIZONTAL OUTSIDE EXHAUST
CUT HOLE THROUGH REAR/WALL FOR EXHAUST ADAPTOR
Trim the rear wall template along the dotted line.
Locate and mark holes to align with holes in the mounting plate.

IMPORTANT:
LOCATE AT LEAST ONE STUD ON EITHER SIDE OF THE CENTERLINE. MARK THE LOCATION FOR 2 ADDITIONAL, EVENLY
SPACED TOGGLE BOLTS IN THE MOUNTING PLATE AREA.
CAUTION – IF EXHAUST ADAPTOR IS POSITIONED OUTSIDE RECOMMENDED DIMENSION, GREASE-LADEN AIR WILL DISCHARGE INTO HOUSE STRUCTURE. 30″ MINIMUM WIDTH REQUIRED REAR WALL TEMPLATE

NOTE: IT IS VERY IMPORTANT TO READ AND FOLLOW THE DIRECTIONS IN THE INSTALLATION INSTRUCTIONS BEFORE PROCEEDING WITH THIS TOP CABINET TEMPLATE.
This template is used to locate the power cord clearance hole, cabinet mounting holes and the vertical exhaust cutout.

1. Determine if your cabinet has a recessed area or a smooth, flat bottom. See Fig. 1. If smooth, tape template onto the bottom surface (Fig. 2). If itis recessed, cut the edges of the template to fit in the recessed bottom of the cabinet. It is important that the edges of the cabinets permit level installation of the oven.
   NOTE: On some cabinets a small bracket or glue block is used between the overhang and the underside of the cabinet bottom. Cut the template to fit around the bracket or glue block so that template will lie flat against the bottom of the cabinet.
   Tape the Top Cabinet Template to the underside of the top cabinet in the recessed area. Fig. 3.
   NOTE: Make sure the rear of the template touches the back wall (for smooth, flat bottom cabinets) or the back of the recess (for recessed bottom cabinets) after cutting the edges of thetemplate.

2. Drill3/8 “diameter holes at A.B. &C.
   CAUTION: Wear safety goggles when drilling holes in the cabinet bottom.

3. Cut out the 2 ” diameter hole atD for power cord. If cabinets are metal, use the nylon grommet (see the Parts Included section in the Installation Instructions) to surround the opening to protect the cord.

4. (FOR VERTICAL EXHAUST ONLY) Cut out shaded areaE. through the cabinet bottom for Vertical (Outside) Exhaust location.

5. Remove the top cabinet template.

6. For recessed cabinets, make 2 filler blocks out of scrap wood the size of the shaded areas F.&G. These filler blocks must have a thickness equal to the depth of the cabinet recess. Drill 1.2″ diameter holes in these blocks to line up with A.&C. . Place the blocks  so that the holes in each block line up with the corresponding holes in the cabinet. The filler blocks should be at the same level as the bottom edge of the wall cabinet frame. Fig. 4.

7. RETURN TO AND PROCEED wi TH THE INSTALLATION STRUCTIONS.

CHECK LIST FOR INSTALLATION

1. Make sure the unit has been installed according to all of the Installation Instructions, the Top Template and Wall Template.
2. Remove all packing material from the oven.
3. Plug in the power cord.
4. Read the Operation Manual.
5. Keep the Installation Instructions for the local electrical inspector’s use.

ACCESSORIES

Check with your dealer or order directly from the SHARP Accessories and Supplies Center.
Call toll-free 1-800-BE SHARP (237-4277).

1. CHARCOAL FILTER (RK233). Filter is used when hood exhaust is recirculated only.
2. GREASE FILTER (RK235) .

PN:16170000A96562

References

• . Spend less. Smile more.
• 800.be - This website is for sale! - 800 Resources and Information.
• Shop Home Appliances & Kitchen Appliances from Sharp USA

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>