NEFF T58PTF1L0 Induction Hob Installation Guide

: June 16, 2024
: Neff

Table of Contents

NEFF T58PTF1L0 Induction Hob
Product Information
General information
Safe installation
Instructions for the electrical connection
Preparing the fitted units
Documents / Resources
- Read User Manual Online (PDF format)
- Download This Manual (PDF format)

NEFF T58PTF1L0 Induction Hob

Product Information

Specifications

Model Number: 9001703326
Date: 020315
Languages: Spanish, Greek, German, Swedish, English, Finnish, French, Polish, Italian, Turkish, Dutch, Russian, Danish, Norwegian

General Information

The appliance must be installed according to the provided installation instructions. Proper installation ensures safe usage of the appliance. The installer is responsible for ensuring that the appliance functions correctly at its installation location.

WARNING: Danger of magnetism! The appliance contains permanent magnets that may affect electronic implants such as pacemakers or insulin pumps. Individuals with electronicimplants must maintain a distance of at least 10 cm from the appliance.

WARNING: Risk of injury! Parts accessible during installation may have sharp edges that can cause cutting injuries. It is recommended to wear protective gloves during installation.

Preparing the Fitted Units

After making the necessary cut-outs, remove any shavings.
Seal the cut surfaces with a heat-resistant material to ensure durability.

Ventilation

To ensure the proper functioning of the appliance, sufficient ventilation is required. The hob must be adequately ventilated, especially in the lower section. Adjust the units if necessary to allow for proper air circulation.

Note: Maintain a minimum clearance between the rear of the appliance and any adjacent surfaces to allow for proper airflow.

Installing the Power Cord

Requirement: This step is applicable only for appliances without a preinstalled power supply.

Turn the hob over and place it on the base of the fitted unit.
Route the power cord into the central area of the main socket.
Close the cover on the socket.
If the power cord obstructs the drawer, use the enclosed cable tie to secure the cable to the underside of the hob.

FAQ

Q: What should I do if I have an electronic implant?
A: If you have an electronic implant, such as a pacemaker or insulin pump, maintain a distance of at least 10 cm from the appliance to avoid any potential effects of magnetism.
Q : Are there any safety precautions during installation?
A: Yes, during installation, it is recommended to wear protective gloves as parts accessible during installation may have sharp edges that can cause cutting injuries.
Q: How should I ensure proper ventilation for the appliance?
A: To ensure proper ventilation, maintain a minimum clearance between the rear of the appliance and any adjacent surfaces. Adjust the fitted units if necessary to allow for proper air circulation.
Q: What should I do if the power cord obstructs the drawer?
A: If the power cord obstructs the drawer, use the enclosed cable tie to secure the cable to the underside of the hob.

General information

Read this instruction manual carefully.
Only a licensed expert may connect the appliance.
Improper installation, opening of the appliance, connection or assembly may lead to a loss of validity of the product warranty.
Switch off the power supply before carrying out any work.
After installation, ensure that the user does not have access to the electrical components.
Never use this appliance in boats or in vehicles

Safe installation

Follow these safety instructions when installing the appliance. The appliance can only be used safely if it is correctly installed in accordance with the installation instructions. The installer is responsible for ensuring that the appliance works perfectly at its installation location.

WARNING ‒ Danger: Magnetism

The appliance contains permanent magnets. They may affect electronic implants, e.g. pacemakers or insulin pumps.

Persons with electronic implants must stand at least 10 cm away from the appliance.

WARNING ‒ Risk of injury

Parts that are accessible during installation may have sharp edges and may lead to cutting injuries.

Wear protective gloves

Instructions for the electrical connection

In order to safely connect the appliance to the electrical system, observe the following instructions.

Only an authorized expert or a specially trained service technician may connect the appliance. The person must be approved in accordance with the local regulations of the country and the electricity supply company.
Connect the appliance to a fixed installation and set up appropriate isolating switches in accordance with the installation regulations.
The manufacturer shall assume no liability for malfunctions or damage resulting from incorrect electrical wiring

Connection type

The appliance corresponds to protection class 1. You should therefore only use the appliance with a protective earth connection

Power cord

The power cord can be connected to the main socket for the hob or included with the appliance.

You can find the required connection data on the type plate and in the connection diagram.
Use only the connection cable that is supplied with the appliance or is supplied by customer service. If you require a longer cable, contact customer service. Connection cables up to 2.20 m
long are available

Information on fitted units

You can only install the induction hob above drawers or ovens with fan ventilation. Do not install refrigerators, dishwashers, non-ventilated ovens, or washing machines below the hob.
Ensure that the fitted unit is heat-resistant up to at least 90 °C.

Worktop
Follow the worktop manufacturer’s recommendations.

Level, horizontal, stable.
The worktop into which you are fitting the appliance must be able to withstand loads of approx. 60 kg.
For thin worktops, use heat-resistant and moisture-resistant reinforcement material.
Only check the evenness of the hob after it has been installed.
You can install the appliance in the following temperatures- resistant, water-resistant worktops
- Marble or natural stone worktops.
- Plastic worktops.
- Solid wood worktops: Only in agreement with the worktop manufacturer (seal the cut-out edges).
- For other worktops: Only in agreement with the
worktop manufacturer.
To level the appliance, do not use supports at individual points.
The cut-out work on the worktop must be carried out by a specialist company in accordance with the installation diagram. The cut edge must be neat and precise because it is visible on the surface. Clean the cut edges with a suitable cleaning product and degrease them.

Extractor hood

The clearance between the extractor hood and the hob must correspond at least to the clearance specified in the installation instructions for the extractor hood

Preparing the fitted units

Mark the unit cut-out in accordance with the installation diagram.
Ensure that the angle of the cut surface to the worktop is 90°. Fig. 1
After making the cut-outs, remove any shavings.
Seal the cut surfaces with heat-resistant material

Ventilation

To guarantee that the appliance works correctly, the hob must be sufficiently ventilated. The ventilation in the lower section of the appliance requires a sufficient supply of fresh air. Therefore, if required, adjust the units for this purpose.

Maintain a minimum clearance between the rear of the unit and the kitchen wall. → Fig. 2
Ensure that an opening at the top of the rear of the unit is unobstructed. → Fig. 3
If the clearance from the back wall of the unit is less than 20 mm, create an opening on the underside. → Fig . 4
If the inside of the unit is not wider than 780 mm, make cuts on the side panels. → Fig. 5
Do not hermetically seal the lower base. Note: If the appliance is installed in an island unit or in another location that is not described here, guaranteethat the hob is ventilated appropriately.

Installation above a drawer

In order to guarantee good ventilation, the clearance between the surface of the worktop and the upper area of the drawer must be 70 mm.→ Fig. 6

Installation above an oven

To ensure good ventilation, the clearance between the top of the worktop and the surface of the oven front must be 30 mm and the minimum clearance between the oven and hob must be 5 mm.
If the clearance between the hob and the oven needs to be increased, refer to the installation instructions for the oven.→ Fig. 7

Installing the power cord in the mains socket

Requirement: For appliances without a preinstalled power supply.

Turn the hob over and put it down on the base of the packaging, a cloth, or another surface in order to prevent scratches. → Fig. 8
Use a screwdriver to lift up the cover of the main socket. → Fig. 9
Undo the fastening screw and use a screwdriver to lift the hose clamp. → Fig. 10
Only connect to the mains socket as shown in the figure: → Fig. 11
BN: Brown
BU: Blue
GN/YE: Green and yellow
BK: Black
GY: Grey
Note: If you implement the connection in accordance with connection diagram 2L/2N, you must change the configuration of the bridges in accordance with the diagram.
After connecting the cable, tighten the screws on the mains socket correctly.
Use the hose clamp to secure the power cord and tighten the fastening screw. → Fig. 12
Route the cables into the central area of the main socket. Close the cover on the socket.
If the power cord gets in the way of the drawer, use the enclosed cable tie to secure the cable to the underside of the hob. → Fig. 13

Inserting the hob

Attach the adhesive tape to the edge of the worktop. → Fig. 14
Insert the hob in the cut-out.
Ensure that the hob is at the same height as the worktop and the appliance does not slip.
Screw the enclosed retaining clips onto the worktop and carefully onto the appliance.
Do not use an electric screwdriver. Fig. 15
Seal the tile joints on tiled work surfaces with silicone rubber.
Before sealing the seals, carry out a suitable function check
Seal all around the gap using suitable, heat-resistant silicone, e.g. Novasil® S70 or Ottoseal® S70.
Smooth the seal joint with a smoother one recommended by the manufacturer. Follow the instructions for the silicone.
Do not operate the appliance until the silicone has dried completely. Drying takes at least 24 hours and the time required depends on the ambient temperature. ‒ A suitable silicone adhesive can be obtained from our customer service. → Fig. 16
Caution! Using unsuitable silicone may result in permanent discoloration of natural marble worktops.

Note: Do not kink or trap the connection cable, and keep it away from sharp edges and hot parts

Connecting the appliance
Requirement: Observe the connection data on the rating plate.

Only connect as shown in the circuit diagram: → Fig. 17, → Fig. 18
BN: Brown
BU: Blue
GN/YE: Green and yellow
BK: Black
GY: Grey
Note: Depending Depending on the type of connection, you may have to change the arrangement of the terminals supplied by the factory. For this, you may have to shorten the clamps and remove the insulation to insert a clamp that connects the two cables.
Check that the appliance is ready for operation: If, or appears on the appliance’s display, the appliance is not connected correctly. Disconnect the appliance from the power supply and check the power cord connection at the main supply.