NEFF D65IEE1S0 Extractor Hood Instruction Manual

: May 15, 2024
: Neff

NEFF D65IEE1S0 Extractor Hood

NEFF-D65IEE1S0-Extractor-Hood-PRODUCT

Specifications

Model Numbers: D65IEE1S0, D85IEE1S0, D65IEE1S0B, D85IEE1S0B
Safety Features: Risk of suffocation, Risk of fire, Risk of burns, Risk of injury
Operating Modes: Exhaust air mode, circulating air mode

Product Information

The extractor hood is designed to remove smoke, steam, and cooking odors from your kitchen. It comes with safety features to prevent suffocation, fire hazards, burns, and injuries. The appliance has different operating modes for efficient ventilation.

Installation Instructions

Ensure adequate fresh air circulation in the room when operating in exhaust air mode.
Consult a chimney sweep to assess ventilation setup for safe operation.
Clean grease filters regularly to prevent fire hazards.
Avoid placing objects on the appliance to prevent falls and injuries.

Usage Instructions

Safety Precautions:

Keep packaging material away from children to prevent suffocation.
Operate the appliance safely with proper room pressure maintenance.
Never operate without grease filters to avoid fire risks.
Avoid touching hot parts of the appliance and keep children at a safe distance.
Clean the appliance carefully to prevent injuries from sharp edges.

Maintenance:
Regularly clean the grease filters and avoid making any changes to the electrical or mechanical assembly of the appliance. Open and close the filter cover carefully to prevent injuries.

Lighting:
Avoid looking directly into the LED lights for extended periods to prevent eye damage.

FAQ

Q: How often should I clean the grease filters?
A: It is recommended to clean the grease filters regularly to prevent fire hazards. Depending on usage, cleaning them once every month or two is advisable.

Q: Can I operate the extractor hood without grease filters?
A: No, it is not safe to operate the appliance without grease filters as fatty deposits can catch fire. Always ensure the filters are in place before using the hood.

Safety

Observe the following safety instructions.

General information

Read this instruction manual carefully.
Keep the instruction manual and the product information safe for future reference or for the next owner.
Do not connect the appliance if it has been damaged in transit.

Intended use

This appliance is designed only to be built into kitchen units. Read the special installation instructions.
The appliance can only be used safely if it is correctly installed according to the safety instructions.
The installer is responsible for ensuring that the appliance works perfectly at its installation location.

Only use this appliance:

For extracting cooking vapour.
in private households and in enclosed spaces in a domestic environment.
up to an altitude of max. 4000 m above sea level.

Do not use the appliance:

With an external timer.

Restriction on user group
This appliance may be used by children aged 8 or over and by people who have reduced physical, sensory or mental abilities or inadequate experience and/or knowledge, provided that they are supervised or have been instructed on how to use the appliance safely and have understood the resulting dangers.
Do not let children play with the appliance.
Children must not perform cleaning or user maintenance unless they are at least 15 years old and are being supervised.
Keep children under the age of 8 years away from the appliance and power cable.

Safe use

WARNING ‒ Risk of suffocation!
Children may put packaging material over their heads or wrap themselves up in it and suffocate.

Keep packaging material away from children.
Do not let children play with packaging material.
Children may breathe in or swallow small parts, causing them to suffocate.
Keep small parts away from children.
Do not let children play with small parts.

WARNING ‒ Risk of poisoning!
Risk of poisoning from flue gases being drawn back in. Room-air-dependent heat-producing appliances (e.g. gas, oil, wood or coaloperated heaters, continuous flow heaters or water heaters) obtain combustion air from the room in which they are installed and discharge the exhaust gases into the open through an exhaust gas system (e.g. a chimney).
With the extractor hood switched on, air is extracted from the kitchen and the adjacent rooms. Without an adequate supply of air, the air pressure falls below atmospheric pressure.

Toxic gases from the flue or the extraction shaft are sucked back into the living space.

Always ensure adequate fresh air in the room if the appliance is being operated in exhaust air mode at the same time as a room-air-dependent heat-producing appliance is being operated.
It is only possible to safely operate the appliance if the pressure in the room in which the heating appliance is installed does not drop more than 4 Pa (0.04 mbar) below atmospheric pressure. This can be achieved whenever the air needed for combustion is able to enter through openings that cannot be sealed, for example in doors, windows,incoming/exhaust air wall boxes or by other technical means. An incoming/exhaust air wall box alone does not ensure compliance with the limit.
In any case, consult your responsible chimney sweep. They are able to assess the house’s entire ventilation setup and will suggest the suitable ventilation measures to you.
Unrestricted operation is possible if the appliance is operated exclusively in circulating- air mode.

WARNING ‒ Risk of fire!
Fatty deposits in the grease filters may catch fire.

Never operate the appliance without a grease filter.
Clean the grease filters regularly.
Never work with naked flames close to the appliance (e.g. flambéing).
Do not install the appliance near a solid fuel heating appliance (e.g. wood- or coalburning) unless the heating appliance has a sealed, non-removable cover. There must be no flying sparks.
Hot oil or grease ignites very quickly.
Always supervise hot oil and fat.
Never extinguish burning oil or fat with water.
Switch off the cooking zone. Extinguish flames carefully using a lid, fire blanket or something similar.
When gas burners are in operation without any cookware placed on them, they can build up a lot of heat. A ventilation appliance installed above the cooker may become damaged or catch fire.
Only operate the gas burners with cookware on them.
Operating multiple gas hobs at the same time generates a great deal of heat. A ventilation appliance installed above the cooker may become damaged or catch fire.
Only operate the gas hobs with cookware on them.
Select the highest fan setting.
Never operate two gas hobs simultaneously on the highest flame for longer than 15 minutes. Two gas hobs correspond to one large burner.
Never operate large burners of more than 5 kW with the highest flame for longer than 15 minutes, e.g. a wok.

WARNING ‒ Risk of burns!
The accessible parts of the appliance become hot during operation.

Never touch these hot parts.
Keep children at a safe distance.
The appliance becomes hot during operation.
Allow the appliance to cool down before cleaning.

WARNING ‒ Risk of injury!
Components inside the appliance may have sharp edges.

Carefully clean the appliance interior.
Items placed on the appliance may fall off.
Do not place any objects on the appliance.
Changes to the electrical or mechanical assembly are dangerous and may lead to malfunctions.
Do not make any changes to the electrical or mechanical assembly.
The filter cover may swing out.
Open the filter cover slowly.
Take hold of the filter cover after opening until it no longer swings out.
Close the filter cover slowly.
Risk of injury when opening and closing the hinges.
Keep your hands away from the hinges.
The light emitted by LED lights is very dazzling, and can damage the eyes (risk group 1).
Do not look directly into the switched-on LED lights for longer than 100 seconds.

WARNING ‒ Risk of electric shock!
If the appliance or the power cord is damaged, this is dangerous.

Never operate a damaged appliance.
Never pull on the power cord to unplug the appliance. Always unplug the appliance at the mains.
If the appliance or the power cord is damaged, immediately unplug the power cord or switch off the fuse in the fuse box.
Call customer services. → Page 9 Incorrect repairs are dangerous.
Repairs to the appliance should only be carried out by trained specialist staff.
Only use genuine spare parts when repairing the appliance.
If the power cord of this appliance is damaged, it must be replaced by trained specialist staff.
An ingress of moisture can cause an electric shock.
Before cleaning, pull out the mains plug or switch off the fuse in the fuse box.
Do not use steam- or high-pressure cleaners to clean the appliance.

WARNING ‒ Risk of explosion!
Highly caustic alkaline or highly acidic cleaning agents in conjunction with aluminium parts in the interior of the appliance may cause explosions.

Never use highly caustic alkaline or highly acidic cleaning agents. In particular, do not use commercial or industrial cleaning agents in conjunction with aluminium parts, e.g. grease filter on extractor hoods.

WARNING ‒ Risk of fire!
Fatty deposits in the grease filters may catch fire.

Clean the grease filters regularly.

WARNING ‒ Risk of injury!
Improper repairs are dangerous.

Repairs to the appliance should only be carried out by trained specialist staff.
If the appliance is defective, call Customer Service.
→ “Customer Service”, Page 9

WARNING ‒ Risk of electric shock!
Penetrating moisture may cause an electric shock.

Do not use wet sponge cloths.

Avoiding material damage

ATTENTION!
Condensate may cause corrosion damage.

To prevent condensation from building up, switch on the appliance during cooking.
If moisture gets into the controls, this may result in damage.
Never clean controls with a wet cloth.
Incorrect cleaning damages the surfaces.
Follow the cleaning instructions.
Do not use harsh or abrasive detergents.
Clean stainless steel surfaces in the direction of the finish only.
Never clean controls with stainless steel cleaners.
Condensation that flows back in may damage the appliance.
The air extraction duct must be installed with a gradient of at least 1° from the appliance.
If you put incorrect stress on the design elements, they may break off.
Do not pull design elements.
Do not place objects on the design elements or hang objects from them.
There is a risk of surface damage if you do not peel off the protective film.
Remove the protective film from all parts of the appliance before using for the first time.

Painted surfaces are easily damaged.

Follow the cleaning instructions.
→ “Cleaning the appliance”, Page 7
Ensure that the painted surfaces are not scratched.

Environmental protection and saving energy

Disposing of packaging
The packaging materials are environmentally compatible and can be recycled.

Sort the individual components by type and dispose of them separately.

Saving energy
If you follow these instructions, your appliance will use less power.
Adjust the fan speed to the amount of steam produced during cooking.

The lower the fan speed, the less energy is consumed.
Only use the intensive mode as required.
If cooking produces large amounts of steam, select a higher fan speed in good time.
The odours are distributed around the room less.
Switch off the lighting if it is no longer required.
When the lighting is switched off, it does not consume any energy.
Clean or replace the filters at regular intervals.
The effectiveness of the filter is retained.
Put the cooking lid on.
The cooking vapours and condensation are reduced.
Only use the additional functions if required.
Switching off additional functions reduces power consumption.

Operating modes

You can use your appliance in air extraction mode or circulating air mode.
The saturation indicator must be adjusted to the selected operating mode and the filters used.

Air extraction mode
The air which is drawn in is cleaned by the grease filters and conveyed to the exterior by a pipe system.

The air must not be discharged into a flue that is used for exhausting fumes from appliances burning gas or other fuels (not applicable to appliances that only discharge the air back into the room).

If the exhaust air is to be conveyed into a non-functioning smoke or exhaust gas flue, you must obtain the consent of the heating engineer responsible.
If the exhaust air is conveyed through the external wall, a telescopic duct should be used.

Air recirculation
The air which is drawn in is cleaned by the grease filters and an odour filter, and conveyed back into the room.

To bind odours in air recirculation mode, you must install an odour filter.
The different options for operating the appliance in air circulation mode can be found in our catalogue. Alternatively, ask your dealer. The required accessories are available from specialist retailers, from our after-sales service or from the online shop.
→ “Accessories”, Page 9

Familiarising yourself with your appliance

Controls
You can use the controls to configure all functions of your appliance and to obtain information about the operating status.

Before using for the first time

Configure the settings for initial start-up. Clean the appliance and accessories.

Setting an operating mode
Your appliance is set to air extraction mode by default.

Note: When using it in circulating-air mode, you require additional accessories.

When using it in circulating-air mode, set the operating mode.

Basic operation

Switching on the appliance

Press ⁠.
The appliance starts at fan setting 2.

Switching off the appliance

Press ⁠ .

Selecting a fan setting

Press ⁠, ⁠ or ⁠.

Switching on intensive mode
If particularly strong odours or vapours develop, you can use intensive mode.

Press ⁠.
After approx. 6 minutes, the appliance automatically switches to fan setting 3.

Switching off intensive mode

Press ⁠.

Switching on the lighting
The lighting can be switched on and off independently of the ventilation system.

Press ⁠ .

Cleaning and servicing

To keep your appliance working efficiently for a long time, it is important to clean and maintain it carefully.

Cleaning products
You can obtain suitable cleaning products from aftersales service or the online shop.

ATTENTION!
Unsuitable cleaning products may damage the surfaces of the appliance.

Do not use harsh or abrasive detergents.
Do not use cleaning products with a high alcohol content.
Do not use hard scouring pads or cleaning sponges.
Only use glass cleaners, glass scrapers or stainless steel care products if recommended in the cleaning instructions for the relevant part.
Wash sponge cloths thoroughly before use.

Cleaning the appliance

Clean the appliance as specified. This will ensure that the different parts and surfaces of the appliance are not damaged by incorrect cleaning or unsuitable cleaning products.

WARNING ‒ Risk of explosion!
Highly caustic alkaline or highly acidic cleaning agents in conjunction with aluminium parts in the interior of the appliance may cause explosions.

Never use highly caustic alkaline or highly acidic cleaning agents. In particular, do not use commercial or industrial cleaning agents in conjunction with aluminium parts, e.g. grease filter on extractor hoods.

WARNING ‒ Risk of electric shock!
An ingress of moisture can cause an electric shock.

Before cleaning, pull out the mains plug or switch off the fuse in the fuse box.
Do not use steam- or high-pressure cleaners to clean the appliance.

WARNING ‒ Risk of burns!
The appliance becomes hot during operation.

Allow the appliance to cool down before cleaning.

WARNING ‒ Risk of injury!
Components inside the appliance may have sharp edges.

Carefully clean the appliance interior.
1. Observe the information regarding the cleaning agents.
2. Clean as follows, depending on the surface:
- Clean stainless steel surfaces in the direction of the finish using a sponge cloth and hot soapy water.
- Clean painted surfaces using a damp sponge cloth and hot soapy water.
- Clean aluminium using a soft cloth and glass cleaner.
- Clean plastic using a soft cloth and glass cleaner.
- Clean glass using a soft cloth and glass cleaner.
1. Dry with a soft cloth.
2. Apply a thin layer of the stainless steel cleaning product to stainless steel surfaces using a soft cloth.
  You can obtain stainless steel cleaning products from the after-sales service or the online shop.

Cleaning controls and lights

WARNING ‒ Risk of electric shock!
Penetrating moisture may cause an electric shock.

Do not use wet sponge cloths.
1. Observe the information regarding the cleaning agents.
2. Clean using a damp sponge cloth and hot soapy water.
3. Dry with a soft cloth.

Cleaning grease filters manually

The grease filters filter the grease from the cooking vapour.
Regularly cleaned grease filters guarantee a high level of grease removal. We recommend cleaning the grease filters every two months.

WARNING ‒ Risk of fire!
Fatty deposits in the grease filters may catch fire.

Clean the grease filters regularly.

Requirement: The grease filters have been removed.

Observe the information regarding the cleaning agents.
Soak the grease filter in hot soapy water.
Use special grease solvent for stubborn dirt. You can obtain grease solvents from customer service or the online shop.
Use a brush to clean the grease filters.
Rinse the grease filters thoroughly.
Allow the grease filters to drain.

Cleaning grease filters in the dishwasher
The grease filters filter the grease from the cooking vapour.
Regularly cleaned grease filters guarantee a high level of grease removal. We recommend cleaning the grease filters every two months.

WARNING ‒ Risk of fire!
Fatty deposits in the grease filters may catch fire.

Clean the grease filters regularly.

ATTENTION!
The grease filters may become damaged if they are squeezed in the dishwasher.

Do not squeeze the grease filters.

Note: When cleaning the grease filter in the dishwasher,light discolouration may occur. This discolouration has no effect on the performance of the metal grease filters.

Requirement: The grease filters have been removed.

Observe the information regarding the cleaning agents.
Place the grease filters loosely into the dishwasher.
Do not clean heavily soiled grease filters with utensils.
Use special grease solvent for stubborn dirt. You can obtain grease solvents from customer service or the online shop.
Start the dishwasher.
Select a temperature of no more than 70 °C.
Allow the grease filters to drain.

Fitting grease filters

ATTENTION!
Falling grease filters may damage the hob below.

Grip below the grease filter with one hand.
1. Fit the grease filters.
2. Fold the grease filters upwards and engage the locks.
3. Make sure that the locks engage.
4. Close the filter cover.

Cleaning the filter cover

Note:

Do not remove the filter cover.
Do not clean the filter cover in the dishwasher.
1. Observe the information regarding the cleaning agents.
2. Clean with a soft cloth and glass cleaner.

Troubleshooting

You can rectify minor faults on your appliance yourself.
Read the troubleshooting information before contacting after-sales service. This will avoid unnecessary costs.

WARNING ‒ Risk of injury!
Improper repairs are dangerous.

Repairs to the appliance should only be carried out by trained specialist staff.
If the appliance is defective, call Customer Service.
→ “Customer Service”, Page 9

WARNING ‒ Risk of electric shock!

Incorrect repairs are dangerous.

Repairs to the appliance should only be carried out by trained specialist staff.
Only use genuine spare parts when repairing the appliance.
If the power cord of this appliance is damaged, it must be replaced by trained specialist staff.

Malfunctions

$NEFF-D65IEE1S0-Extractor-Hood-FIG- $3$$

Disposal

Disposing of old appliance
Valuable raw materials can be reused by recycling.

Unplug the appliance from the mains.
Cut through the power cord.
Dispose of the appliance in an environmentally friendly manner.
Information about current disposal methods are available from your specialist dealer or local authority.

This appliance is labelled in accordance with European Directive 2012/19/EU concerning used electrical and electronic appliances (waste electrical and electronic equipment – WEEE).
The guideline determines the framework for the return and recycling of used appliances as applicable throughout the EU.

Customer Service

Function-relevant genuine spare parts according to the corresponding Ecodesign Order can be obtained from Customer Service for a period of at least 10 years from the date on which your appliance was placed on the market within the European Economic Area.

Note: Under the terms of the manufacturer’s warranty the use of Customer Service is free of charge.
Detailed information on the warranty period and terms of warranty in your country is available from our aftersales service, your retailer or on our website.
If you contact Customer Service, you will require the product number (E-Nr.) and the production number (FD) of your appliance.

The contact details for Customer Service can be found in the enclosed Customer Service directory or on our website.

Product number (E-Nr.) and production number (FD)
You can find the product number (E-Nr.) and the production number (FD) on the appliance’s rating plate.

Depending on the model, the rating plate can be found:

Inside the appliance (remove grease filters for access).
On top of the appliance.
Make a note of your appliance’s details and the Customer Service telephone number to find them again quickly.

Accessories

You can buy accessories from the after-sales service,from specialist retailers or online. Only use original accessories, as these have been specifically designed for your appliance.
Accessories vary from one appliance to another. When purchasing accessories, always quote the exact product number (E no.) of your appliance. → Page 9
You can find out which accessories are available for your appliance in our catalogue, in the online shop or from our after-sales service. www.neff- international.com

Installation instructions

Observe this information when installing the appliance.

Included with the appliance
After unpacking all parts, check for any damage in transit and completeness of the delivery.

Dimensions
You will find the dimensions of the appliance here

Safety clearances
Comply with the safety clearances for the appliance.

For Australia and New Zealand the minimum safety clearance above electrical cooktops must be 600 mm.

Secure installation
Follow these safety instructions when installing the appliance.

WARNING ‒ Risk of poisoning!
Risk of poisoning from flue gases being drawn back in. Room-air-dependent heat-producing appliances (e.g. gas, oil, wood or coaloperated heaters, continuous flow heaters or water heaters) obtain combustion air from the room in which they are installed and discharge the exhaust gases into the open through an exhaust gas system (e.g. a chimney).
With the extractor hood switched on, air is extracted from the kitchen and the adjacent rooms. Without an adequate supply of air, the air pressure falls below atmospheric pressure.
Toxic gases from the flue or the extraction shaft are sucked back into the living space.

Always ensure adequate fresh air in the room if the appliance is being operated in exhaust air mode at the same time as a room-air-dependent heat-producing appliance is being operated.
It is only possible to safely operate the appliance
if the pressure in the room in which the heating appliance is installed does not drop more than 4 Pa (0.04 mbar) below atmospheric pressure. This can be achieved whenever the air needed for combustion is able to enter through openings that cannot be sealed, for example in doors, windows, incoming/exhaust air wall boxes or by other technical means. An incoming/exhaust air wall box alone does not ensure compliance with the limit.
In any case, consult your responsible chimney sweep. They are able to assess the house’s entire ventilation setup and will suggest the suitable ventilation measures to you.
Unrestricted operation is possible if the appliance is operated exclusively in circulating- air mode.
Risk of poisoning from flue gases being drawn back in.
If an extractor hood with an open-flued heat production source is installed, the power supply for the extractor hood must be provided with a suitable safety switch.
Risk of poisoning from flue gases being drawn back in.
Do not emit the exhaust air into a smoke or exhaust gas flue that is in operation.
Do not emit the exhaust air into a shaft that is used to ventilate installation rooms for heat-producing appliances.
If the exhaust air is to be conveyed into a smoke or exhaust gas flue, you must obtain the consent of the heating engineer responsible.

WARNING ‒ Risk of suffocation!
Children may put packaging material over their heads or wrap themselves up in it and suffocate.

Keep packaging material away from children.
Do not let children play with packaging material.

WARNING ‒ Risk of fire!
Grease deposits in the grease filter may catch fire.

The specified safety clearances must be complied with in order to prevent a build-up of heat.
Observe the specifications for your cooking appliances. If the installation instructions for the cooking appliances specify a different clearance, the larger of the two must always be provided for. If gas hobs and electric hobs are operated together, the largest specified clearance applies.
The appliance must be installed with no more than one side directly next to a highsided unit or a wall. The distance between the appliance and wall or high-sided unit must be at least 50 mm.
The grease deposits in the grease filter may catch fire.
Never work with naked flames close to the appliance (e.g. flambéing).
Do not install the appliance near a heatproducing appliance for solid fuel (e.g. wood or coal) unless a closed, non-removable cover is present. There must be no flying sparks.

WARNING ‒ Risk of injury!
Components inside the appliance may have sharp edges.

Wear protective gloves.
The appliance may fall down if it has not been properly fastened in place.
All fastening components must be fixed firmly and securely in place.
Risk of injury from glass splinters.
Protect the filter cover against impact.
Do not drop the filter cover.
Wear protective goggles during installation.
The appliance is heavy.
To move the appliance, two people are required.
Use only suitable tools and equipment.
The appliance is heavy.
The appliance must not be fitted directly onto plasterboard or similar lightweight materials.
To ensure correct installation, you must use a material which is sufficiently stable and suitable for both the structural conditions and the weight of the appliance.

Changes to the electrical or mechanical assembly are dangerous and may lead to malfunctions.

Do not make any changes to the electrical or mechanical assembly.
The filter cover may swing out.
Open the filter cover slowly.
Take hold of the filter cover after opening until it no longer swings out.
Close the filter cover slowly.
Risk of injury when opening and closing the hinges.
Keep your hands away from the hinges.

WARNING ‒ Risk of electric shock!
Sharp-edged components inside the appliance may damage the connecting cable.

Do not kink or trap the connecting cable. If the appliance or the power cord is damaged, this is dangerous.
Never operate a damaged appliance.
Never pull on the power cord to unplug the appliance. Always unplug the appliance at the mains.
If the appliance or the power cord is damaged, immediately unplug the power cord or switch off the fuse in the fuse box.
Call customer services. → Page 9 Incorrect repairs are dangerous.
Repairs to the appliance should only be carried out by trained specialist staff.
Only use genuine spare parts when repairing the appliance.
If the power cord of this appliance is damaged, it must be replaced by trained specialist staff.

Incorrect installation is dangerous.

Connect and operate the appliance only in accordance with the specifications on the rating plate.
Connect the appliance to a power supply with alternating current only via a properly installed socket with earthing.
The protective conductor system of the domestic electrical installation must be properly installed.
Never equip the appliance with an external switching device, e.g. a timer or remote control.
When the appliance is installed, the mains plug of the power cord must be freely accessible. If free access is not possible, an all-pole isolating switch must be installed in the permanent electrical installation according to the conditions of Overvoltage Category III and according to the installation regulations.
When installing the appliance, check that the power cable is not trapped or damaged.

General information
Follow these general instructions during the installation.

For the installation, observe the currently valid building regulations and the regulations of the local electricity and gas suppliers.
When discharging the exhaust air, the official and legal regulations, such as the regional building code., must be observed.
In order to freely access the appliance for servicing, select an easy-to-reach installation site.
The surfaces of the appliance are sensitive. Avoid damaging them during installation.

Instructions for the electrical connection
In order to safely connect the appliance to the electrical system, follow these instructions.

WARNING ‒ Risk of electric shock!
It must always be possible to disconnect the appliance from the electricity supply. The appliance must only be connected to a protective contact socket that has been correctly installed.

The mains plug for the mains power cable must be easily accessible after the appliance is installed.
If this is not possible, an all-pole isolating switch must be integrated into the permanent electrical installation according to the conditions of overvoltage category III and according to the installation regulations.
The permanent electrical installation must only be wired by a professional electrician. We recommend installing a residual-current circuit breaker (RCCB) in the appliance’s power supply circuit.
Sharp-edged components inside the appliance may damage the connecting cable.
Do not kink or trap the connecting cable.
- The connection data can be found on the rating plate. → Page 9
- The connecting cable is approx. 1.30 m long.
- This appliance complies with the EC interference suppression regulations.
- The appliance corresponds to protection class 1.
  You should therefore only use the appliance with a protective earth connection.
- Do not connect the appliance to the power supply during installation.
- Ensure that the protection against contact is guaranteed during installation.

Information on the installation situation

Install this appliance on the kitchen wall.
To install additional special accessory parts, observe the enclosed installation instructions.
The appliance must be installed with no more than one side directly next to a high-sided unit or a wall.
The distance between the appliance and wall or high-sided unit must be at least 50 mm.
The width of the extractor hood must correspond at least with the width of the hob.
To optimally detect the cooking vapours, install the appliance in the middle of the hob.

Instructions for the exhaust air pipe
The appliance manufacturer does not provide any warranty for faults attributable to the pipeline.

Use a short, straight exhaust air pipe with as large a pipe diameter as possible.
Long, rough exhaust air pipes, many pipe bends or small pipe diameters reduce the suction power and increase the fan noise.
Use an exhaust pipe that is made of non-combustible material.
To prevent condensate from returning, fit the exhaust pipe with a 1° gradient from the appliance.

Flat ducts
Use flat ducts with an inner cross-section that corresponds to the diameter of the round pipes:

Diameter of 150 mm corresponds to approx.
177 cm².
Diameter of 120 mm corresponds to approx.
113 cm².
Use sealing strips for different pipe diameters.
Do not use any flat ducts with sharp bends.
Round pipes
Use round pipes with an inner diameter of 150 mm (recommended) or at least 120 mm.

Instructions for the air extraction mode
For air extraction mode, a one-way flap should be installed.

Notes

If a one-way flap is not included with the appliance, one can be ordered from a specialist retailer.
If the exhaust air is conveyed through the external wall, a telescopic duct should be used.

Installation
Preparing the appliance

Remove the grease filters.
To avoid causing damage, do not bend the grease filters.

Checking the wall

Check whether the wall is horizontal and adequately load-bearing.
The maximum weight of the appliance is 25 kg.
Drill the hole depth in accordance with the length of the screws.
Install the appliance with a fixing material which is sufficiently stable and has been adjusted accordingly for both the structural conditions and the weight of the appliance.
Check the cut-out area for existing cables of other appliances.

Preparing the wall

Cover the hob to prevent damage.
Remove the drilling template.
The cardboard drilling template is part of the packaging.
Mark a vertical centre line on the wall from the ceiling to the lower edge of the appliance.
Using the drilling template, measure and mark the positions of the fastening screws.
The bottom edge of the appliance is identical to the lower edge of the drilling template.
Ensure that there are no electrical wires, gas pipes or water pipes in the area where holes are to be drilled.
Drill holes with a diameter of 8 mm.
Drill the hole depth in accordance with the length of the screws.
Insert the wall plugs flush with the wall.
Remove the angle bracket for the flue duct.
Screw in two fastening screws with washers to approx. 5 mm.
Attach 1 and 2 align the appliance.
Mark the hole for the safety screw.
Remove the appliance once more.

Attaching the appliance

Drill an 8 mm hole for the safety screw.
Insert the wall plugs flush with the wall.
Attach the appliance.
Screw in the safety screw with the washer.

You can also use the right or left hole opening.

Fitting the flue duct

To separate the flue duct sections, remove the adhesive tape.
Remove the protective foil from both flue duct sections.
Note:
- To prevent scratches, lay paper over the edges of the outer flue duct section to protect the surface.
- The slots on the inner flue duct section should point downwards.
  Push one flue duct section into the other.
Insert the lower flue duct section into the brackets on the left and right on the appliance ⁠.
Screw the upper flue duct to the sides of the fixing bracket using 2 short screws ⁠.
Fit the grease filters.
To avoid causing damage, do not bend the grease filters.

Fitting the filter cover

WARNING ‒ Risk of injury!
Components inside the appliance may have sharp edges.

Wear protective gloves.
Risk of injury from glass splinters.
Protect the filter cover against impact.
Do not drop the filter cover.
Wear protective goggles during installation.
1. Align the filter cover at an angle of 90° to the appliance.
2. Insert the brackets for the filter cover into the openings on the appliance and lock into place.
3. Remove the edge protection.

Valid within Great Britain:
Imported to Great Britain by
BSH Home Appliances Ltd.
Grand Union House
Old Wolverton Road
Wolverton, Milton Keynes
MK12 5PT
United Kingdom

Register your product online
neff-home.com

BSH Hausgeräte GmbH
Carl-Wery-Straße 34
81739 München, GERMANY