COMPEX WLE3000HX Wi-Fi 6 Mu Mimo Dual Band Module User Guide

COMPEX WLE3000HX Wi-Fi 6 Mu Mimo Dual Band Module

Product Information

• Specifications
  • Product Model: WWLLEE31020160VHX
  • Power Requirements: DC Power, 3.3V
  • Power Consumption: 9W max
• Component Map
  • RF Exposure Considerations
  • This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment.
  • This equipment should be installed and operated with a minimum distance of 20cm between the radiator and your body.
  • Antenna Type and Gain
  • The following antennas have been certified for use with this module.
  • Only antennas of the same type with equal or lower gain may also be used with this module.
  • Other types of antennas and/or higher gain antennas may require additional authorization for operation.
• Antenna Specification list below:
  • Antenna 1: Type – X, Gain – Y
  • Antenna 2: Type – A, Gain – B
  • Antenna 3: Type – C, Gain – D

Component Map

Power Requirements

• DC Power 3.3V
• Power Consumption 9W (max)

MiniPCIe Slot Pin Assignment

Mechanical key E
17| NC| 18| GND
19| NC| 20| NC
21| GND| 22| PCIE0_PERST
23| PCIE0_RX0_N| 24| VDD_3V3
25| PCIE0_RX0_P| 26| GND
27| GND| 28| NC
29| GND| 30| NC
31| PCIE0_TX0_N| 32| NC
33| PCIE0_TX0_P| 34| GND
35| GND| 36| NC
37| NC| 38| NC
39| VDD_3V3| 40| GND
41| VDD_3V3| 42| NC
43| GND| 44| NC
45| NC| 46| NC
47| NC| 48| NC
49| NC| 50| GND
51| NC| 52| VDD_3V3

FCC Statement

This device complies with Part 15 of the FCC Rules.

Operation is subject to the following two conditions:

1. This device may not cause harmful interference, and
2. this device must accept any interference received, including interference that may cause undesired operation.

This equipment has been tested and found to comply with the limits for a Class B digital device, under Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used by the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment to an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

This module has been tested and found to comply with Part 15.247 & 407 requirements for Modular Approval.
FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate this equipment. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.

Antenna Placement Within the Host Platform

1. The module is installed in the host: PCWL-0500, the antenna must be installed such that 55 cm is maintained between the antenna and users.
2. The module is installed in the host: PCWL-0510, the antenna must be installed such that 65 cm is maintained between the antenna and users.,

If these conditions cannot be met (for example certain laptop configurations or co-location with another transmitter), then the FCC authorization is no longer considered valid and the FCC ID cannot be used on the final product. In these circumstances, the OEM integrator will be responsible for re-evaluating the end product (including the transmitter) and obtaining a separate FCC authorization.

Trace antenna designs Not applicable

• Note EMI Considerations
  • A host manufacturer is recommended to use D04 Module Integration Guide recommending as “best practice” RF design engineering testing and evaluation in case non-linear interactions generate additional non-compliant limits due to module placement to host components or properties.
  • For standalone mode, reference the guidance in the D04 Module Integration Guide and for simultaneous mode7; see D02 Module Q&A Question 12, which permits the host manufacturer to confirm compliance.
• How to make changes
  • Only Grantees are permitted to make permissive changes. If this module will be used differently than granted, please contact us.
• Limited modular
  • The module will be restricted on these host (Detailed information show as below)
  • Man ufacturer: PicoCELA Inc
  • Mo del No.: PCWL-0510, PCWL-0500
• RF exposure considerations
  • Thi s equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator & your bod y.
• Antenna Type and Gain
  • The following antennas have been certified for use with this module.
  • O nly antennas of the same type with equal or lower gain may also be used with this module.
  • Other types of antennas and/or higher gain antennas may require the additional authorization for operation. Antenna Specification list below:

End Product Labeling
When the module is installed in the host device, the FCC ID label must be visible through a window on the final device or it must be visible when an access panel, door or cover is easily removed. If not, a second label must be placed on the outside of the final device that contains the following text:

“Contains FCC ID: TK4WLE3000HX”. The FCC ID can be used only when all FCC compliance requirements are met. The end product shall bear the following 15.19 statement: This device complies with part 15 of the FCC Rules.

Operation is subject to the following two conditions:

1. This device may not cause harmful interference, and
2. This device must accept any interference received, including interference that may cause undesired operation.

Information on test modes and additional testing requirements

• This transmitter is tested in a standalone mobile RF exposure condition and any co-located or simultaneous transmission with another transmitter (s) class II permissive change re-evaluation or new certification.

Part 15 Subpart B disclaimer

• This transmitter module is tested as a subsystem and its certification does not cover the FCC Part 15 Subpart B rule requirement applicable to the final host.
• The final host will still need to be reassessed for compliance to this portion of rule requirements if applicable.
• As long as all conditions above are met, further transmitter test will not be required. However, the OEM integrator is still responsible for testing their end-product for any additional compliance requirements required with this module installed.

Important Note

• In the event that these conditions can not be met (for example certain laptop configurations or co-location with another transmitter), then the FCC authorization is no longer considered valid and the FCC I D can not be used on the final product.
• In these circumstances, the OEM integrator will be responsible for reevaluating the end product (including the transmitter) and obtaining a separate FCC authorization.

Manual Information to the End User

• The OEM integrator has to be aware not to provide information to the end user regarding how to install or remove this RF module in the user’s manual of the end product which integrates this module.
• The host integrator must follow the integration instructions provided in this document and ensure that the composite-system end product complies with the requirements by a technical assessment or evaluation to the rules and to KDB Publication 996369 .
• The host integrator installing this module into their product must ensure that the final composite product complies with the requirements by a technical assessment or evaluation to the rules, including the transmitter operation and should refer to guidance in KDB 996369.

OEM/Host manufacturer responsibilities

• OEM/Host manufacturers are ultimately responsible for the compliance of the Host and Module.
• The final product must be reassessed against all the essential requirements of the FCC rule such as FCC Part 15 Subpart B before it can be placed on the US market.
• This includes reassessing the transmitter module for compliance with the Radio and EMF essential requirements of the FCC rules.

IC Statement

• This Class B digital apparatus complies with Canadian ICES-003.
• This device complies with Industry Canada licence-exempt RSS standard(s).

Operation is subject to the following two conditions:

1. This device may not cause interference, and
2. This device must accept any interference, including interference that may cause undesired operation of the device.

RF Radiation Exposure Statement:
This equipment complies with ISED radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance of 20 centimeters between the radiator and your body.

Caution:

1. the device for the band 5150-5250 MHz is only for indoor usage to reduce potential for harmful interferenceto co-channel mobile satellite systems.
2. for devices with detachable antenna(s), the maximum antenna gain permitted for devices in the bands 5250-5350 MHz and 5470-5725 MHz shall be such that the equipment still complies with the e.i.r.p. limit;
3. for devices with detachable antenna(s), the maximum antenna gain permitted for devices in the band 5725-5850 MHz shall be such that the equipment still complies with the e.i.r.p. limits as appropriate;

IMPORTANT NOTE
In the event that these conditions cannot be met (for example certain laptop configurations or co-location with another transmitter), then the Canada authorization is no longer considered valid and the IC cannot be used on the final product. In these circumstances, the OEM integrator will be responsible for re-evaluating the end product (including the transmitter) and obtaining a separate Canada authorization.
Required end product labeling:
This transmitter module is authorized only for use in device where the antenna may be installed and operated with greater than 20cm between the antenna and users. The end product must be labeled in a visible area with the following: “Contains IC:7849A WLE3000HX”.

Manual Information To the End User
The OEM integrator has to be aware not to provide information to the end user regarding how to install or remove this RF module in the user’s manual of the end product which integrates this module. The end user manual shall include all required regulatory information/warning as show in this manual. The following text, or an equivalent notice, shall be displayed in a conspicuous location, either in the user manual or on the device, or both: This device contains licence-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic Development Canada’s license-exempt RSS(s).

Operation is subject to the following two conditions:

1. This device may not cause interference.
2. This device must accept any interference, including interference that may cause undesired operation of the device.

Antenna

• The following antennas have been certified for use with this module; antennas of the same type with equal or lower gain may also be used with this module.
• The antenna must be installed such that 20 cm can be maintained between the antenna and users.
• This radio transmitter has been approved by Innovation, Science and Economic Development Canada to operate with the antenna types listed below, with the maximum permissible gain indicated.
• Antenna types not included in this list that have a gain greater than the maximum gain indicated for any type listed are strictly prohibited for use with this device.

Antenna Specification list below:

CONTACT

• Copyright © Compex Systems. All rights reserved. COMPEX and the COMPEX logo, are registered trademarks of Compex Systems Pte. Ltd..
• While every effort is made to ensure the information is accurate, Compex does not accept liability for any errors or mistakes that may arise. All specifications are subject to change without notice.
• Compex Systems Pte Ltd
• www.compex.com.sg
• (+65) 6288 8220
• sales@compex.com.sg
• Last Updated: 31/05/2022 SL, LL, AT, GS

References

• Home | Compex Systems: Leader in OEM/ODM Wireless Integration

Read User Manual Online (PDF format)

Download This Manual (PDF format)

Download this manual  >>