Compex Systems WLW7000E2 Electric Heated Pad User Guide
- June 14, 2024
- Compex Systems
Table of Contents
Compex Systems WLW7000E2 Electric Heated Pad
Specifications:
- Power Requirements: DC Power
- Power: 5V (Max)
- Power Consumption: 12.3W
Component Map:
- CH0 CH1 CH2 CH3
- Ground Pin
- 5V External Power Pin
- M.2 E Key Edge Connector
M.2 Edge Connector Pin Assignment:
Top side
| Pin | Assignment |
|---|---|
| 1 | GND |
| 2 | VDD_3V3 |
| 3 | REFCLK_IO_P0 |
| 4 | VDD_3V3 |
| 5 | REFCLK_IO_N0 |
| 6 | PCIE_LED0(GPIO25) |
| 7 | GND |
| 8 | NC |
| 9 | PTA2_BT_ACT |
| 10 | NC |
| 11 | PTA2_BT_PRIO |
| 12 | NC |
| 13 | PTA2_WL_ACT |
| 14 | WSI_DAT_OUT(GPIO48) |
| 15 | VDD_5V |
| 16 | NC |
Bottom side
| Pin | Assignment |
|---|---|
| 17 | VDD_5V |
| 18 | GND |
| 19 | VDD_5V |
| 20 | WSI_CLK_OUT(GPIO49) |
| 21 | VDD_5V |
| 22 | NC |
| 23 | VDD_5V |
| 24 | NC |
| 25 | NC |
| 26 | NC |
| 27 | NC |
| 28 | NC |
| 29 | NC |
| 30 | NC |
| 31 | NC |
| 32 | WSI_DAT_IN(GPIO50) |
| 33 | GND |
| 34 | GND |
| 35 | PCIE0_RX0_P |
| 36 | WSI_CLK_IN(GPIO51) |
| 37 | PCIE0_RX0_N |
| 38 | NC |
| 39 | GND |
| 40 | NC |
| 41 | PCIE0_TX0_P |
| 42 | NC |
| 43 | PCIE0_TX0_N |
| 44 | PTA1_BT_PRIO |
| 45 | GND |
| 46 | PTA1_WL_ACT |
| 47 | PCIE0_REFCLK_P |
| 48 | PTA1_BT_ACT |
| 49 | PCIE0_REFCLK_N |
| 50 | NC |
| 51 | GND |
| 52 | PCIE0_RST_N |
| 53 | PCIE0_CLKREQ_N |
| 54 | NC |
| 55 | PCIE0_WAKE_N |
| 56 | WLAN_DISABLE |
| 57 | GND |
| 58 | NC |
| 59 | NC |
| 60 | NC |
| 61 | NC |
| 62 | NC |
| 63 | GND |
| 64 | NC |
| 65 | NC |
| 66 | NC |
| 67 | NC |
| 68 | NC |
| 69 | GND |
| 70 | NC |
| 71 | REFCLK_IO_N1 |
| 72 | VDD_3V3 |
| 73 | REFCLK_IO_P1 |
| 74 | VDD_3V3 |
| 75 | GND |
Product Usage Instructions
Power Requirements:
The product requires DC power at a maximum voltage of 5V.
M.2 E Key Edge Connector:
The product features an M.
Component Map
Power Requirements
- DC Power 5V (Max)
- Power Consumption 12.3W
For the customer who want to use 5V External Power Pin, please make sure pins 15, 17, 19, 21 and 23 were not connected with your board.
M.2 Edge Connector Pin Assignment
M.2 edge connector pin assignment
Top side| Bottom side
1| GND| 2| VDD_3V3
3| REFCLK_IO_P0| 4| VDD_3V3
5| REFCLK_IO_N0| 6| PCIE_LED0(GPIO25)
7| GND| 8| NC
9| PTA2_BT_ACT| 10| NC
11| PTA2_BT_PRIO| 12| NC
13| PTA2_WL_ACT| 14| WSI_DAT_OUT(GPIO48)
15| VDD_5V| 16| NC
17| VDD_5V| 18| GND
19| VDD_5V| 20| WSI_CLK_OUT(GPIO49)
21| VDD_5V| 22| NC
23| VDD_5V| |
Mechanical key E
33| GND| 32| WSI_DAT_IN(GPIO50)
35| PCIE0_RX0_P| 34| GND
37| PCIE0_RX0_N| 36| WSI_CLK_IN(GPIO51)
39| GND| 38| NC
41| PCIE0_TX0_P| 40| NC
43| PCIE0_TX0_N| 42| NC
45| GND| 44| PTA1_BT_PRIO
47| PCIE0_REFCLK_P| 46| PTA1_WL_ACT
49| PCIE0_REFCLK_N| 48| PTA1_BT_ACT
51| GND| 50| NC
53| PCIE0_CLKREQ_N| 52| PCIE0_RST_N
55| PCIE0_WAKE_N| 54| NC
57| GND| 56| WLAN_DISABLE
59| NC| 58| NC
61| NC| 60| NC
63| GND| 62| NC
65| NC| 64| NC
67| NC| 66| NC
69| GND| 68| NC
71| REFCLK_IO_N1| 70| NC
73| REFCLK_IO_P1| 72| VDD_3V3
75| GND| 74| VDD_3V3
Copyright © Compex Systems. All rights reserved. COMPEX and the COMPEX logo,
are registered trademarks of Compex Systems Pte. Ltd.
While every effort is made to ensure the information is accurate, Compex does
not accept liability for any errors or mistakes that may arise.
All specifications are subject to change without notice.
Compex Systems Pte Ltd
www.compex.com.sg
(+65) 6288 8220
[email protected]
Last Updated: 02/11/2023
MW, LL, GS, AT