MODERN OFFICE ET223T Electric Desk Frame Installation Guide
- October 30, 2023
- MODERN OFFICE
Table of Contents
MODERN OFFICE ET223T Electric Desk Frame
Overview
Technical data
- Column qty: 3
- Max Loading capacity: 150KG
- Height range: 580-1230mm
Accessory list
Component list
Note: This standing desk has three angle installation methods,90 °, 120 ° and 180
Installation
Connect the two supporting beams (5) to the left and right connecting plates (6) (7) with screws (C) and (E) respectively. There are three angles to choose at will and finally tighten them with a wrench (!)
Connect the lifting columns (3) to the support beam (5) with screws (D), the middle column (3) to the left and right connecting plates (6) (7), and the wrench (I) to tighten the screws. 90° and 180° are installed in the same way as 120%.
Install the long feet and the liting column (3) together, use wrench (I) to tighten the screws (C)
Install long and short the feet(1)(2) and the lifting column (3) together, use wrench (1) to tighten the screws (C)
Connect the left and right support plates (5] and the support beam (4) with screws (A), connect the middle support plate (5) with the left and right connection plates (6) (7), and tighten the screws with a wrench (I); 90° and 180° are installed in the same way as 120°
The telescopic distance of the beam can be adjusted according to the actual use, the adjustment method is the same as step 6-1
Control Panel
Operation Instruction
Product Outline
Product Specification
Bottom introduction: There are seven buttons that “A”, “V”, “1”, “2”, “3”, “M”, “A
- : Adjust the desk upwards
- : Adjust the desk downwards
- “1”: Position 1, first height position saved by the user
- “2”: Position 2, second height position saved by the user
- “3”: Position 3, third height position saved by the user
- “M”: Height memory function
- “A” : Alert button to remind users changing posture
Operating Instructions
-
Height Adjustable Function:
Press the button to adjust the height. The LED display shows the current height. -
Height Memory Function:
-
a. Press UP or DOWN button and adjust the height to the desired height. Press “M” to save the height, and the screen will display “5-“:
Press “1” , “2” or “3′ then, that is, save the height to the corresponding position 1 or 2 or 3, which will show in the display screen as “5 -1” “5 -2”, or “5-3”: -
b. Press ‘1″ “2” and “3” button directly to automatically adjust the memory height you saved.
-
-
Reminder Function:
- a. Press REMINDER button “A” to activate the function. The LED display shows “Of”
- b. Two seconds later, press the button to adjust the reminder time only when the display screen flashes. The default time of the reminder is 45 minutes, which is shown as “- 45″. Then press any button to save the time setup, or wait 5 seconds and system will save the time setup automatically. During the countdown, any operation will lead to a repeat starting of the timer. When the countdown finishes, display screen will show ” 0g ” the buzzer will be active with a 10-second “DiDi…DiDi…DiDi..”tone.
- c. Within the 10-second reminder buzz, press any button to reactivate the time countdown that is set up in (b) step. If no operation during the 10-second reminder buzz, there will be another reminder buzz after 5 minutes. No operation during the second buzz will turn off the Long-Time Sitting Reminder.
- d. Press and hold the “A” button for three seconds to turn off the Long-Time Sitting Reminder. The LED display shows “OFf”.
Anti-collision sensitivity adjustment – optional features:
- a. Press and hold the button for 5 seconds at the same time to switch the sensitivity. Switch one file for 1 time and divide it into 4 files (A-3, A-2, A-1, A-0);
- b. The display shows “R-0”, the anti-collision function is off; the display shows “R-“, low sensitivity; Display shows “R-2″, medium sensitivity; display shows”R-3”, high sensitivity;
- c. During height adjustment, when tabletop comes in contact with another object, instantly stops and reverses to avoid damage.
- d. Press and hold the button for 5 seconds at the same time. If the display does not display the above code, there is no anti-collision function.
Troubleshooting
- a. Reset: When the LED shows”R5f”, press button until the desk reaches its to lowest height and rebounds to stop, it means the reset has been finished.
- b. When it does’t work and the LED shows “E01” or “E02”, please retry 18 mins later.
- c. If the button does’t work, please check the cable connection and then cut off thepower for at least 10 seconds. Reconnect to the power and press button to start the reset process when it shows the ‘ASr”.
- d. If all these above process are inefficient. olz contact our customer service.
Waste disposa l
This marking indicates that this product should not be disposed with other
household wastes. To prevent possible harm to the environment or human health
from uncontrolled waste disposal, recycle it responsibly to promote the
sustainable reuse of material resources. To retum your used device, please use
the retur and collection systems or contact the retailer where the product was
purchased. They can take this product for environmental safe recycling.
www.modernofficefurniture.com
For customer service call: 1-800-443-5117
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>