MR CARTOOL M50 Smart Slope Meter User Manual

MR CARTOOL M50 Smart Slope Meter

Product Information

Specifications

• Voltage Measurement Range: DC10V~30V
• Voltage Measurement Accuracy: 0.5V
• Speed Accuracy: 0.36Km/h
• GPS Data Refresh Rate: 1s
• GPS Hot Start: 1s AVG
• Wireless Transmission Frequency: 2.4GHz
• GPS Cold Start: 32s AVG
• Weight: 230g
• Product Size: 1272560MM

Product Usage Instructions

Driving Unit Setting
To access the driving unit setting, follow these steps:

1. Press and hold the function selection button.
2. The function interface will appear.
3. Short press the function selection button to navigate to the driving unit setting.
4. Adjust the parameters as needed.
5. Press and hold the on/off button to save and exit.

Over Speed Alarm Setting
To configure the over-speed alarm, please follow these steps:

1. Press and hold the function selection button.
2. The function interface will appear.
3. Short press the function selection button to navigate to the over speed alarm setting.
4. Adjust the parameters to set the desired speed limit for the alarm.
5. Press and hold the on/off button to save and exit.

Speed Compensation Setting
To set the speed compensation, perform the following steps:

1. Press and hold the function selection button.
2. The function interface will appear.
3. Short press the function selection button to navigate to the speed compensation setting.
4. Adjust the parameters to compensate for any speed discrepancies.
5. Press and hold the on/off button to save and exit.

Time Compensation Setting – Minus
To configure the time compensation setting with a minus value, follow these instructions:

1. Press and hold the function selection button.
2. The function interface will appear.
3. Short press the function selection button to navigate to the time compensation setting (minus).
4. Adjust the parameters to compensate for any time discrepancies.
5. Press and hold the on/off button to save and exit.

Time Compensation Setting – Plus
To configure the time compensation setting with a plus value, follow these instructions:

1. Press and hold the function selection button.
2. The function interface will appear.
3. Short press the function selection button to navigate to the time compensation setting (plus).
4. Adjust the parameters to compensate for any time discrepancies.
5. Press and hold the on/off button to save and exit.

FAQ

• Q: What is the voltage measurement range of the Smart Slope Meter?
  A: The voltage measurement range is DC10V~30V.

• Q: What is the accuracy of the speed measurement?
  A: The speed accuracy is 0.36 km/h.

• Q: What is the wireless transmission frequency of the Smart Slope Meter?
  A: The wireless transmission frequency is 2.4GHz.

Product introduction

This product is an automotive slope meter with a built-in multi-axis gyroscope and GPS. It supports 99% of the car models in the market. It can measure the vehicle’s pitch angle, roll angle, driving speed, altitude, and driving direction, which greatly improve driving safety and provide a better journey experience.

Features

• Pitch angle: Real-time measurement of the vehicle pitch angle during driving, the range is -40°~ +40°between between upside and downside.
• Roll angle: Real-time measurement of the vehicle roll angle during driving, the range is -40°~ +40°between left-side and right-side.
• Vehicle speed: Real-time monitoring of the current speed of the vehicle.
• Altitude: The current altitude can be measured by the vehicle.
• Safety alarm prompts: When the pitch angle and roll angle of the vehicle exceeds the default alarm value, the device will issue a safety alarm”beep”.

Product Parameters

• Power supply: DC10V~30V;
• Operating temperature: －40°C~＋80°C;
• Pitch angle:－ 40°~＋40°;
• Roll angle: －40°~+40°;
• Voltage measurement range: DC10V~30V;
• Voltage measurement accuracy: 0.5V;
• Speed accuracy: ＜0.36Km/h; ;
• GPS data refresh rate: 1s;
• GPS hot start: 1s（AVG）
• Wireless transmission frequency: 2.4GHz;
• GPS cold start: 32s（AVG）
• Weight: 230g;
• Product Size: 1272560MM

Structure

1. Function select buttons;
2. On/off button;
3. Digital display area;
4. Power supply interface;
5. Holder interface.

Display Interface Details

1. Pitch angle display
2. Roll angle display
3. Altitude display
4. Longitude and latitude display
5. Driving unit display
6. Voltage display
7. Alarm beep display
8. Fatigue driving alarm display
9. Over-speed alarm display
10. Driving speed display
11. Clock display
12. Compass display
13. GPS positioning icon signal display

Detailed Explanation of Functions

1. Driving unit setting;
2. Over speed alarm setting;
3. Speed compensation setting;
4. Time compensation setting–minus;
5. Time compensation setting–plus；

Press and hold press the function selection button to enter theabove function interface, short press it to adjust the parameters, and press and hold the on/o button to save and exit.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>