BLACK DECKER FW1610 16 Inch Wall Fan Instruction Manual
- June 16, 2024
- Black Decker
Table of Contents
BLACK DECKER FW1610 16 Inch Wall Fan
Specifications
- Product Name : ALLIN Fan
- Usage : Indoor
- Power Source : Electrical supply
- Plug Type : Polarized plug
- Assembly Components : Fan blades, front grill, clips, fan blade securing cap, securing ring, rear grill, handle, motor shaft, pin, subject, power cord, hanging board, knob, drawstring, bolt, nut, drywall plugs, screws
Before Assembly
- Read and follow all instructions before operating the fan.
- Check for any damage or missing parts. Do not use the fan if any part is damaged or missing.
- Ensure the fan is intended for indoor use only.
- Unplug the fan from the electrical supply source before cleaning.
- If the power cord is damaged, contact your local service center or a qualified electrician for appropriate replacement.
- This appliance is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities unless they have been given supervision or instruction concerning the use of the appliance by a person responsible for their safety.
- Children should be supervised to ensure they do not play with the appliance.
Assembly Steps
- Drill two holes in the wall first, with a distance of 32mm (1.3 inches) between the holes.
- Insert two drywall plugs into the holes and lock the screws, ensuring a distance of 5mm (0.2 inches) between the wall and the screws.
- Align the holes on the fan hanging board with the two screws on the wall and hang the subject (fan) on the hanging board.
- Remove the securing ring from the motor cover by rotating it clockwise to loosen it.
- Install the rear grill to the corresponding position of the motor cover, then lock the securing ring counterclockwise and lift the handle upward.
- Insert the fan blades onto the motor shaft pin, securing them using the fan blade securing cap by turning it counter-clockwise to tighten.
- Install the front grill over the top of the rear grill and fasten them together using the clips attached to the front grill.
- Fully tighten the small nut and bolt that passes through the rim of the grills.
Attention : Make sure the notches on the fan blade assembly are seated firmly on the arms of the fan shaft. Fasten the retaining cap securely before use.
16”WALL FAN
INSTRUCTION/OPERATING MANUAL
READ AND FOLLOW ALL INSTRUCTION
CAUTION
Read and follow all instructions before operating fan. Do not use fan if any part is damage or missing.
WARNING
- . To reduce the risk of fire or electric shock, do not use this fan with any solid-state speed control device.
- This appliance has a polarized plug which is intended to fit in an outlet only one way. If this does not fit the outlet, contact a qualified electrician. Do not attempt to bypass this procedure.
- This product is to be used indoors.
- Unplug from the electrical supply source before cleaning.
- If the power cord is damaged, contact your local service center or a qualified electrician to install an appropriate replacement cord to prevent any injury or damage.
- This appliance is not intended for use by persons(including children) with reduced physical, sensory or. mental capabilities, or lack of experience and knowledge unless they have been given supervision or instruction concerning use of the appliance by a person responsible for their safety.
- .Children should be supervised to ensure that they do not play with the appliance.
RULES FOR SAFE OPERATION
- Never insert fingers, pencils, or any other object through the guard when fan is running.
- Disconnect the fan when moving from one location to another.
- Disconnect the fan when removing the grills for cleaning.
- Be sure the fan is on a stable surface when operating to avoid overturning.
- DO NOT use a fan in the window. Rain may create electrical hazards.
- The fan is for home use only.
- Do not leave the fan running unattended.
ASSEMBLY
Before commencing assembly familiarize yourself with all the assembly components (See chart and diagram).
- Drill two holes in the wall first, the distance between the holes is 32mm(1.3″) (fig.4 );
- Put two drywall plugs(17) (fig.2) into the hole, and then lock the screws(18) (fig.3), the distance between the wall and the screw is 5mm(0.2”);
- Align the holes on the fan hanging board(12) plate with the two screws on the wall, and then hang the subject(10).
- Remove the securing ring(5) of the back net from the motor cover and rotate it clockwise to loosen it.
- Install the rear grill(6) to the corresponding position of the motor cover, then lock the securing ring(5), lock it counterclockwise, and lift the handle(?) upward;(see fig11)
- Insert the fan blades(4) onto the motor shaft(8) pin(9), securing the fan blades using the fan blade securing cap(3), turning counter-clockwise to tighten;
- Install the front grill (1) over top of the rear grill(6). Fasten the two grills with the clips(2) attached to the front grill.
- Fully tighten the small nut(16) and bolt(15) that passes through the rim of the grills.
Attention : Notches on the fan blade assembly must be seated firmly on the arms of the fan shaft.
Fasten the retaining cap securely before use.
ASSEMBLY CMfONENTS
- front grill
- clips
- fan blade securing cap
- fan blades
- securing ring
- rear grill
- handle
- . motor shaft
- pin
- subject
- power cord
- hanging board
- knob
- drawstring
- bolt
- nut
- drywall plugs
- screws
INSTRUCCIONES DE OPERACION
- To adjust the tilt angle of the fan head upward or downward by simply moving the guard up or down.
- For a vertical angle, pull the operating knob until the desired angle is achieved.
- Pull the rope to choose the desired speed (high-mediumslow-ciff). Pull the rope to turn off the fan.
USER SERVICING INSTRUCTION
- Grasp the plug and remove it from the receptacle or other outlet device. Do not unplug by pulling on the cord
- 0pen fuse cover. Slide open fuse access cover on top of attachment plug towards blades, (see Fig. 5)
- Remove the fuse carefully. Remove the. fuse by prying it out carefully, (see Fig. 6)
- Risk of fire. Replace fuse only with 5Amp max, 125 Volt fuse.
- Close fuse cover. Slide closed the fuse access cover on top of the attachment plug, (see Fig. 7).
- Risk of fire. Do not replace the attachment plug. Contains a safety device (fuse) that should not be removed. Discard product if the at! The attachment plug is damaged.
Tips : Do not overexert when replacing the fuse or damage may occur. If it’s hard to close the access cover, make sure the fuse is fully inserted.
CLEANING
- Be sure to unplug from the electrical supply source before cleaning.
- Plastic parts should be cleaned with mild soap and a damp cloth or sponge. Thoroughly remove the soap film with clean water.
- Be sure not to get water or other liquid into the motor.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>