SJOSTRAND M10001UK Stainless steel Espresso Machine Instruction Manual
- June 16, 2024
- SJOSTRAND
Table of Contents
The Original
**Instruction Manual
**
Thank you for purchasing The Original. This manual will help you get to know
your new machine and how you best take care of it.
For more instructions and information about the machine, check out the QR code
below:
TECHNICAL SPECIFICATIONS
Pump pressure | 19 bars |
---|---|
Capsule container capacity | 15 capsules |
Removable water tank volume | 1.2 litres |
Drip tray | Adjustable and removable |
Brew ratio/cup sizing | Automatic and programmable |
Power Saver mode | Activates after 28 minutes |
Power | AC220-240V, 50-60Hz, 1200-1400W |
Weight | 4 kg |
Dimensions (H x W x D) in mm
Standard: | 258 x 192 x 337 |
---|---|
Without drip tray: | 258 x 192 x 263 |
With lever up: | 338 x 192 x 337 |
Brew Ratios | Espresso / lungo / custom |
--- | --- |
Capsule System* | Nespresso ® Original |
- Only Sjöstrand and Nespresso ® Original capsules are guaranteed to work with The Original.
GETTING STARTED
-
lnsert the power socket into a power outlet.
-
Fill water tank with cold water.
-
Place the drip tray in the appropriate height for your cup size.
(It is possible to detach the drip tray and lay it flat at the bottom surface underneath the no zzle for larger cups). -
Switch the machine ON by flipping the toggle switch up.
-
Both the espresso and lungo buttons will start blinking to indicate that the machine is w arming up. The machine is ready to use when the lights stops blinking and stays on.
-
Run 4-6 cups of water before your first brew.
USING YOUR MACHINE
TO-DOs FOR EACH USE
- Make sure the water tank is filled.
- Turn the machine ON.
- Wait until the machine is preheated (blinking lights stay on).
- Pull down the lever without using a capsule.
- Press either of the brew ratio buttons to run water through the machine.
- Pull the lever up again.
- Drop a coffee capsule in the capsule inlet and pull the capsule inlet lever down.
- Press the espresso button for an expresso (40 ml).
- Press the lungo button for a lungo (100 ml).
It is not recommended to fill the water tank with hot water. Keep in mind the Max/Min volume levels.
AFTER USING YOUR MACHINE
- Turn the machine OFF after each use.
- Lift and keep the capsule inlet lever up to release the capsule.
- Empty the capsule container and the drip tray.
- Keep the lever in a pushed-down position till the next use.
CHANGING THE BREW RATIO
By factory default, the two brew ratio buttons—espresso and lungo—will output
their corresponding amounts of coffee of 40 ml or 100 ml.
For a custom amount of coffee, press and hold either of the brew ratio buttons
until the machine has outputted your desired amount of coffee. The memory
function on each button will remember your set preferences for next time.
If you press either button as normal and accidentally press it again before
its done, the machine will interpret it as a custom selection and will store
the setting.
To change back to the original brew ratio settings, perform a factory reset
(p. 11).
MAINTAINING YOUR MACHINE
DEAIRING THE MACHINE
When your new machine arrives, it is completely out of water, and you will
need to deair it to let water in. You will notice this when you have filled
the water tank, but no water comes out when it’s supposed to start brewing.
The machine will also make the same noise it does when performing a normal
brewing procedure.
To deair your machine, follow the steps below:
- Turn the machine ON.
- Fill up the water tank.
- Have the capsule inlet lever in its upright position. Push it slightly further back towards the back of the machine until you hear a sound.
- Run a cup of water through the machine before brewing a cup of coffee by pressing either the espresso or the lungo button. Your machine is deaired when water comes out of the nozzle.
AIRING THE MACHINE
If you are moving the machine or plan not to use it for a long period of time, we recommend that you air it. You will then drain the machine completely of water to avoid freezing and leaking.
- Switch ON the machine.
- Pull the capsule inlet lever down (without a capsule).
- Push either of the brew ratio buttons.
- As soon as water starts pouring out, remove the water tank.
Once the water stops pouring, the airing of the machine is complete.
CLEANING
- Use a damp cloth with mild, non-abrasive cleaning detergent.
DESCALING
Descaling your machine is a necessary part of keeping it fresh and ensuring the besttasting coffee. Not descaling your machine can also lead to issues. For example, the machine can start leaking if the coffee cannot flow through it properly. How often a descaling should be carried out depends on the amount of lime in the water in your area. For a moderate amount, we recommend descaling at least twice a year. For areas with mineral-rich water, it should be up to once every third month.
- Carefully read the use and safety instructions on the descaling package.
- Be careful when handling the descaling solution near the machine as it could harm the machine’s surface.
- Do not use vinegar!
THE DESCALING PROCESS
- Make sure that the water tank is filled with at least 0.5 litres of water.
- Make sure that the capsule inlet is empty.
- Empty the capsule container and the drip tray.
- Let water run through the machine (without a capsule).
- Add the descaling solution to the water tank.
- Place a cup or container underneath the nozzle.
- Press and hold both the espresso and lungo buttons simultaneously for 2 seconds.
- Press either of the two buttons to start the procedure.
- Let the descaling solution run through the machine for a second time.
- Fill the water tank with fresh water.
- Run 6-8 cups of water through to make sure the machine is free of any descaling solution residue.
THE DESCALING ALARM
After 1200 uses (brewing coffee and water), the descaling alarm is triggered
every time the machine is switched on. When you turn the power switch on, the
LED indicators of the brew ratio buttons will be flashing at a frequency of
5x/second, stopping for 1 second, and repeats. The machine will then start
preheating and can be used normally. The alarm can only be reset when the user
operates the descaling process.
TROUBLESHOOTING
THE LIGHTS WON´T TURN ON
- The machine has entered power safe mode which happens after 28 minutes of non-use.
- Toggle the ON/OFF switch.
- Check the condition of the power cord, the voltage, and the fuse.
THE LIGHTS ARE BLINKING IRREGULARLY
- Make sure that it’s not the descaling alarm (described on p. 9) that’s causing the blinking lights. If it is, perform the descaling procedure (p. 9).
- Check the water tank. If empty, fill with fresh water.
NO/NOT ENOUGH COFFEE/WATER IS COMING OUT OF THE MACHINE
- Check the water tank. If empty, fill with fresh water.
- Check that the machine has not been programmed to dispense a small amount of co ffee. Perform a factory reset (p. 11) if unsure.
THE COFFEE ISN’T HOT ENOUGH
- Preheat the coffee cup with hot water.
- Descale the machine if necessary.
THE CAPSULE INLET DOESN’T CLOSE COMPLETELY
- Empty the capsule container.
- Check that there is no capsule jammed inside the machine.
WATER IS LEAKING INTO THE CAPSULE CONTAINER
- Check that the water tank is properly mounted.
- Make sure you are using either Sjöstrand coffee capsules or Nespresso ® Originalffee capsules.
- Make sure the black, round filter plate, is properly in place and not clogged. The filter plate is the rough textured component that penetrates the capsule membrane during the brewing process and sits in the front part of the capsule inlet. You can use a brush (e.g. old toothbrush) and carefully brush over the filter plate to remove residues.
- Try brewing 2-3 cups of water to wash out the machine. Dried-up coffee residue that’s left in the machine due to non-use can sometimes clog it up.
- Descale your machine according to the descaling solution manufacturer’s instructions. This is needed to be done more frequently in areas with lime-rich water.
NO COFFEE COMES OUT, ONLY WATER
- Make sure an unused capsule is placed in the coffee capsule inlet.
- Make sure that the capsule you are using is compatible with the machine.
- Make sure that the capsule inlet lever is fully pulled down and engaged.
COFFEE CAPSULE IS STUCK INSIDE THE CAPSULE INLET
- Push the capsule inlet lever up and press any button to let the water pressure dislodge the capsule.
- As soon as the capsule has been removed, turn off the machine to prevent any water fr om splashing out.
- If a capsule has dried out and gotten stuck, pour some water on it to soften it up.
FACTORY RESET
- Turn the machine OFF.
- Press and hold the lungo button and turn the machine ON while still pressing the button.
For other issues or if the issues
remain, contact us at
info@sjostrandcoffee.com
Sjöstrand Trading AB
Box 55989
102 16 Stockholm
Sweden
www.sjostrandcoffee.com
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>