Focal K2 Power Series 6 1 2 Inch Component Speaker System User Guide
- June 16, 2024
- FOCAL
Table of Contents
- K2 Power Series 6 1 2 Inch Component Speaker System
- ES 100 KE / ES 165 KE / ES 165 K2S
- ES 100 KE
- READ FIRST! IMPORTANT SAFETY INSTRUCTIONS!
- Specifications
- SPECIAL PRECAUTIONS
- Product Sheet
- Technical Sheet
- FREQUENCY RESPONSE/IMPEDANCE
- References
- Read User Manual Online (PDF format)
- Download This Manual (PDF format)
K2 Power Series 6 1 2 Inch Component Speaker System
K2 POWER
ES 100 KE | EC 165 KE | ES 165 KE | ES 165 K2E
ES 165 KX2E | ES 165 KX3E | ES 165 K2S
SUB 25 KXS | SUB 30 KXE | SUB 25 KXE
Quick Start
GO TO THE
USER MANUAL
https://www.focal.com/usermanual/k2-power
ES 100 KE / ES 165 KE / ES 165 K2S
ES 165 KX2E / ES 165 KX3E / ES 165 K2E
ES 165 KX2E
ES 165 KX3E
ES 165 KX2E / ES 165 KX3E | TWEETER FRAK
ES 100 KE / ES 165 KE / ES 165 K2E / ES 165 K2S | TWEETER TKME
ES 100 KE
ES 165 KE
ES 165 K2S
ES 165 K2E
ES 165 KX2E
ES 165 KX3E
SUB 25 KXS / SUB 25 KXE / SUB 30 KXE
READ FIRST! IMPORTANT SAFETY INSTRUCTIONS!
The exclamation mark represented in an equilateral triangle is intended to alert users to the existence of important instructions in the user manual relating to the use and maintenance of the device.
- Read these instructions.
- Keep these instructions.
- Heed all the warnings.
- Follow all the instructions.
- To avoid damaging your hearing, do not listen to loudspeakers at high volumes for long periods of time. Listening to loudspeakers at high volumes can cause damage to the user’s ears and may lead to hearing problems (temporary or permanent deafness, buzzing in the ears, tinnitus, hyperacusis). Exposure to excessive volumes (over 85dB) for more than one hour can cause irreparable damage to your hearing.
- If a subwoofer is installed in your vehicle, it is important to secure it firmly. We recommend that you attach the enclosure to the floor or chassis of the vehicle for safety. If the subwoofer is not properly secured, it could become a projectile in the event of an accident. This point is even more important if the subwoofer is installed in a hatchback, a station wagon, a utility vehicle or a van.
- If cables or harnesses are provided, use them the proper way (like mentioned in this user manual) without replacing or modifying them.
- If a fuse is included in the kit or harness, use only same rating one in case of replacement .
The methods of installing and mounting loudspeakers to any surface (vehicle
floor or chassis) depend on the conditions and standards of installation,
refurbishment, safety and cabling in force and applicable to the surfaces
and/or brackets involved. In addition, the products may vibrate and damage the
brackets onto which they are mounted. For this reason, the installation
operations must be performed by a qualified professional who is familiar with
installation and safety standards. Focal does not provide any end-of-use
warranty for a given bracket or installation, as installing the loudspeakers
is the customer’s sole responsibility. Focal is therefore not liable in any
capacity whatsoever in the event of incident, accident and/or any other result
or damage of any kind related to the installation of loudspeakers.
Conditions of warranty
All Focal loudspeakers are covered by warranty drawn up by the official Focal
distributor in your country. Your distributor can provide all details
concerning the conditions of warranty. Warranty cover extends at least to that
granted by the legal warranty in force in the country where the original
purchase invoice was issued.
REGISTER YOUR PRODUCT ONLINE
www.focal.com/warranty Focal-JMlab ®
– BP 374 – 108, rue de l’Avenir – 42353 La Talaudière cedex – France –
www.focal.com
Tel. (+33) 04 77 43 57 00 – Fax (+33) 04 77 43 57 04 – SCCG – 09/02/2023 – v3
– CODO1712
K2 POWER
ES 100 KE | EC 165 KE | ES 165 KE | ES 165 K2E ES 165 KX2E | ES 165 KX3E | ES
165 K2S SUB 25 KXS | SUB 30 KXE | SUB 25 KXE
User manual
ES 100 KE / ES 165 KE / ES 165 K2S
ES 165 K2E
ES 165 KX3E
ES 165 KX2E / ES 165 KX3E | TWEETER FRAK
ES 165 K2S
ES 165 K2E
ES 165 KX3E
SUB 25 KXS / SUB 25 KXE / SUB 30 KXE
Specifications
ES 100 KE
Membrane | K2 Sandwich |
---|---|
Médium | 100 mm |
Puissance max. | 120 W |
Puissance nom. | 60 W RMS |
Sensibilité (2,83 V/1 m) | 90 dB |
Impédance | 4 Ω |
Réponse en frequency | 110 Hz – 22 kHz |
Diamètre bobine | 20 mm |
Profounder | 39 mm |
Moteur | Néodyme |
Suspension | TMD® |
Tweeter | Profil “M” |
Filtre | 12/12 dB (3,5 kHz) |
Hauteur bobine | 8,5 mm |
Niveau tweeter adjustable | +3/0/-3 dB/oct |
ES 100 KE
Cone | K2 Sandwich |
---|---|
Midrange | 4″ (100mm) |
Maximum power | 120W |
Nominal power | 60W RMS |
Sensitivity (2.83V/1m) | 90dB |
Impedance | 4Ω |
Frequency response | 110Hz-22kHz |
Voice-coil diameter | 3/4″ (20mm) |
Depth | 1 ” (39mm) |
Magnet | Neodymium |
Suspension | TMD® |
Tweeter | M-Shaped |
Crossover | 12/12dB (3.5kHz) |
Voice-coil height | 3/8″ (8.5mm) |
Adjustable tweeter level | +3/0/-3dB/oct |
ES 165 KE
Membrane | K2 Sandwich |
---|---|
Woofer | 165 mm |
Puissance max. | 200 W |
Puissance nom. | 100 W RMS |
Sensibilité (2,83 V/1 m) | 91 dB |
Impédance | 4 Ω |
Réponse en fréquence | 60 Hz – 22 kHz |
Diamètre bobine | 32 mm |
Profondeur | 74 mm |
Moteur | Ferrite |
Suspension | TMD® |
Tweeter | Profil “M” |
Filtre | 6 – 12/12 dB (3 kHz) |
Hauteur bobine | 15 mm |
Niveau tweeter ajustable | +3/0/-3 dB/oct |
**ES 165 KE**
Cone | K2 Sandwich |
---|---|
Woofer | 6 1/2 ” (165mm) |
Maximum power | 200W |
Nominal power | 100W RMS |
Sensitivity (2.83V/1m) | 91dB |
Impedance | 4Ω |
Frequency response | 60Hz-22kHz |
Voice-coil diameter | 1 1/4 ” (32mm) |
Depth | 3″ (74mm) |
Magnet | Ferrite |
Suspension | TMD® |
Tweeter | M-Shaped |
Crossover | 6-12/12dB (3kHz) |
Voice-coil height | 5/8″ (15mm) |
Adjustable tweeter level | +3/0/-3dB/oct |
ES 165 K2E
Membrane | K2 Sandwich |
---|---|
Woofer | 165 mm |
Puissance max. | 200 W |
Puissance nom. | 100 W RMS |
Sensibilité (2,83 V/1 m) | 93 dB |
Impédance | 2 Ω |
Réponse en fréquence | 60 Hz – 22 kHz |
Diamètre bobine | 32 mm |
Profondeur | 74 mm |
Moteur | Ferrite |
Suspension | TMD® |
Tweeter | Profil “M” |
Filtre | 6 – 12/12 dB (3,5 kHz) |
Hauteur bobine | 15 mm |
Niveau tweeter ajustable | +3/0/-3 dB/oct |
ES 165 K2E
Cone | K2 Sandwich |
---|---|
Woofer | 6 1/2 ” (165mm) |
Maximum power | 200W |
Nominal power | 100W RMS |
Sensitivity (2.83V/1m) | 93dB |
Impedance | 2Ω |
Frequency response | 60Hz – 22kHz |
Voice-coil diameter | 1 1/4 ” (32mm) |
Depth | 3″ (74mm) |
Magnet | Ferrite |
Suspension | TMD® |
Tweeter | M-Shaped |
Crossover | 6-12/12dB (3.5kHz) |
Voice-coil height | 5/8″ (15mm) |
Adjustable tweeter level | +3/0/-3dB/oct |
ES 165 KX3E (Woofer) | ES 165 KX3E (Medium) |
--- | --- |
Membrane | K2 Sandwich |
Diametre | 165 mm |
Puissance max. | 240 W |
Puissance nom. | 120 W RMS |
Sensibilite (2,83 V/1 m) | 93 dB |
Impedance | 4 ID |
Reponse en frequence | 45 Hz – 32 kHz |
Diametre bobine | 40 mm |
Profondeur | 76 mm |
Moteur | Ferrite |
Suspension | TMD’ |
Tweeter | Aluminium, profil “M” |
Filtre | 6 -12/12/12 dB (3/4/500/3/5 kHz) |
Niveau tweeter ajustable | +3/0/-3 dB/oct |
ES 165 KX3E (Woofer) | ES 165 KX3E (Midrange) |
--- | --- |
Cone | K2 Sandwich |
Diameter | 6 1/2 ” (165mm) |
Maximum power | 240W |
Nominal power | 120W RMS |
Sensitivity (2.83V/1m) | 93dB |
Impedance | 4Ω |
Frequency response | 45Hz-32kHz |
Voice-coil diameter | 2″ (40mm) |
Depth | 3″ (76mm) |
Magnet | Ferrite |
Suspension | TMD® |
Tweeter | Aluminium, M-Shaped |
Crossover | 6-12/12/12dB (3/4/500/3/5kHz) |
Adjustable tweeter level | +3/0/-3dB/oct |
EC 165 KE
Membrane | K2 Sandwich |
---|---|
Woofer | 165 mm |
Puissance max. | 160 W |
Puissance nom. | 80 W RMS |
Sensibilité (2,83 V/1 m) | 93 dB |
Impédance | 4 Ω |
Réponse en fréquence | 60 Hz – 22 kHz |
Diamètre bobine | 25 mm |
Profondeur | 74 mm |
Moteur | Ferrite |
Suspension | TMD® |
Tweeter | Profil “M” |
Filtre | Intégré |
Hauteur bobine | 15 mm |
EC 165 KE
Cone | K2 Sandwich |
---|---|
Woofer | 6 1/2 “(165mm) |
Maximum power | 160W |
Nominal power | 80W RMS |
Sensitivity (2.83V/1m) | 93dB |
Impedance | 4Ω |
Frequency response | 60Hz-22kHz |
Voice-coil diameter | 1″ (25mm) |
Depth | 3″ (74mm) |
Magnet | Ferrite |
Suspension | TMD® |
Tweeter | M-Shaped |
Crossover | Integrated |
Voice-coil height | 5/8″ (15mm) |
ES 165 KX2E
Membrane | K2 Sandwich |
---|---|
Woofer | 165 mm |
Puissance max. | 240 W |
Puissance nom. | 120 W RMS |
Sensibilité (2,83 V/1 m) | 92,5 dB |
Impédance | 2 Ω |
Réponse en fréquence | 55 Hz – 32 kHz |
Diamètre bobine | 40 mm |
Profondeur | 76 mm |
Moteur | Ferrite |
Suspension | TMD® |
Tweeter | Profil “M” |
Filtre | 6 – 12/12 – 18 dB (3 kHz) |
Hauteur bobine | 16,5 mm |
Niveau tweeter ajustable | +3/0/-3 dB/oct |
ES 165 KX2E
Cone | K2 Sandwich |
---|---|
Woofer | 6 ” (165mm) |
Maximum power | 240W |
Nominal power | 120W RMS |
Sensitivity (2.83V/1m) | 92.5dB |
Impedance | 2Ω |
Frequency response | 55Hz-32kHz |
Voice-coil diameter | 2″ (40mm) |
Depth | 3″ (76mm) |
Magnet | Ferrite |
Suspension | TMD® |
Tweeter | M-Shaped |
Crossover | 6-12/12-18dB (3kHz) |
Voice-coil height | 5/8″ (16.5mm) |
Adjustable tweeter level | +3/0/-3dB/oct |
ES 165 K2S
Membrane | K2 Sandwich |
---|---|
Woofer | 165 mm |
Puissance max. | 140 W |
Puissance nom. | 70 W RMS |
Sensibilité (2,83 V/1 m) | 88 dB |
Impédance | 2 Ω |
Réponse en fréquence | 60 Hz – 22 kHz |
Diamètre bobine | 32,5 mm |
Moteur | Ferrite |
Suspension | TMD® |
Tweeter | Profil “M” |
Filtre | 6 – 12/12 dB (3 kHz) |
Hauteur bobine | 13 mm |
Niveau tweeter ajustable | +3/0/-3 dB/oct |
ES 165 K2S
Cone | K2 Sandwich |
---|---|
Woofer | 6 ” (165mm) |
Maximum power | 140W |
Nominal power | 70W RMS |
Sensitivity (2.83V/1m) | 88dB |
Impedance | 2Ω |
Frequency response | 60Hz-22kHz |
Voice-coil diameter | 1 1/4 ” (32.5mm) |
Magnet | Ferrite |
Suspension | TMD® |
Tweeter | M-Shaped |
Crossover | 6-12/12dB (3kHz) |
Voice-coil height | 1/2″ (13mm) |
Adjustable tweeter level | +3/0/-3dB/oct |
SUB 25 KXE
Membrane | K2 Sandwich |
---|---|
Subwoofer | 250 mm |
Puissance max. | 1200 W |
Puissance nom. | 600 W RMS |
Sensibilité (2,83 V/1 m) | 84,5 dB |
Impédance | 2 x 4 Ω |
Réponse en fréquence | 25 Hz – 5 kHz |
Diamètre bobine | 65 mm |
Profondeur | 172 mm |
Moteur | Ferrite |
Hauteur bobine | 55 mm |
SUB 25 KXE
Cone | K2 Sandwich |
---|---|
Subwoofer | 10″ (250mm) |
Maximum power | 1200W |
Nominal power | 600W RMS |
Sensitivity (2.83V/1m) | 84.5dB |
Impedance | 2×4Ω |
Frequency response | 25Hz-5kHz |
Voice-coil diameter | 2 1/2 ” (65mm) |
Depth | 6 3/4 ” (172mm) |
Magnet | Ferrite |
Voice-coil height | 2″ (55mm) |
SUB 25 KXS
Membrane | K2 Sandwich |
---|---|
Subwoofer | 250 mm |
Puissance max. | 700 W |
Puissance nom. | 350 W RMS |
Sensibilité (2,83 V/1 m) | 84,5 dB |
Impédance | 4 Ω |
Réponse en fréquence | 25 Hz – 5 kHz |
Diamètre bobine | 45 mm |
Moteur | Neodymium |
Hauteur bobine | 32 mm |
SUB 25 KXS
Cone| K2 Sandwich
Subwoofer| 10″ (250mm)
Maximum power| 700W
Nominal power| 350W RMS
Sensitivity (2.83V/1m)| 84.5dB
Impedance| 4Ω
Frequency response| 25Hz-5kHz
Voice-coil diameter| 1 3/4 ” (45mm)
Magnet| Neodymium
Voice-coil height| 1 1/4 ” (32mm)
SUB 30 KXE
Membrane| K2 Sandwich
Subwoofer| 300 mm
Puissance max.| 1600 W
Puissance nom.| 800 W RMS
Sensibilité (2,83 V/1 m)| 86,5 dB
Impédance| 2 x 4 Ω
Réponse en fréquence| 25 Hz – 5 kHz
Diamètre bobine| 65 mm
Profondeur| 172 mm
Moteur| Ferrite
Hauteur bobine| 55 mm
SUB 30 KXE
Cone| K2 Sandwich
Subwoofer| 12″ (300mm)
Maximum power| 1600W
Nominal power| 800W RMS
Sensitivity (2.83V/1m)| 86.5dB
Impedance| 2×4Ω
Frequency response| 25Hz-5kHz
Voice-coil diameter| 2 1/2 ” (65mm)
Depth| 6 3/4 ” (172mm)
Magnet| Ferrite
Voice-coil height| 2″ (55mm)
READ FIRST! IMPORTANT SAFETY INSTRUCTIONS!
Warning symbol. This symbol is designed to warn the user of the presence of important instructions mentioned and relating to the handling, operation and maintenance of the device.
- Read these instructions.
- Keep these instructions.
- Heed all warnings.
- Follow all the instructions.
- Do not use this device near water.
- After removing the product from its packaging, keep the packaging out of the reach of children. It poses a suffocation risk.
- Never use chemical products or abrasive detergents to clean the device. Clean with a dry cloth only.
- Do not obstruct ventilation openings, as this may alter the sound quality of the device.
- During storage, the device should not be exposed to temperatures below 20°C or above 80°C. The operating temperature range for the device is between -10°C and 50°C.
- If the product emits smoke or an unusual smell, immediately turn off the power supply (turn off the ignition and remove the key) and stop using it. Contact your retailer as soon as possible.
- Do not turn on any function likely to distract you when driving. Functions or settings that require prolonged attention should only be used when the vehicle is at a complete stop. There is a risk of accident.
- Do not listen to the loudspeakers at a high volume, so that you can hear external noise when driving.
- If cords or connectors are supplied, use them properly as described in the user manual without replacing them or modifying them.
- If the kit or connector includes a fuse, it must only be replaced by a fuse of the same rating.
- Do not attempt to repair this device yourself. Opening the device may exposeyou to dangerous voltages or other risks.
- All maintenance tasks should be performed by a qualified professional. Maintenance is required in case of any kind of damage to the device (spillages or objects inserted into the device, exposure to rain, if the device malfunctions or is dropped, etc.).
- When replacement components are needed, make sure that the maintenancetechnician uses the components recommended by the manufacturer or components with exactly the same technical features as the original product.Using non-compliant components could cause fires, electric shocks or other risks.
- After any maintenance or repair workon the device, ask the maintenance technician to test it to check that it is working safely.
- If a subwoofer is installed in the vehicle, it is essential to secure it by attaching it solidly. We recommend attaching the subwoofer to the floor or chassis of the vehicle for safety. If it is not properly secured, it could become a projectile in the event of an accident. This is even more important if the subwoofer is installed in a hatchback, a station wagon, a utility vehicle or a van.
- Some users who are not self-sufficient enough to use the product on their own without danger. In particular, children under 14 or people with some types of disabilities must be supervised and/or accompanied when using the device.
- To avoid damaging your hearing, do not listen to loudspeakers at high volumes for long periods of time. Listening to loudspeakers at high volumes can cause damage to the user’s ears and may lead to hearing problems (temporary or permanent deafness, buzzing in the ears, tinnitus, hyperacusis). Exposure to excessive volumes (over 85dB) for more than one hour can cause irreparable damage to your hearing .
The methods of installing and mounting loudspeakers to any surface (bracket, ground anchoring, etc.) depend on the conditions and standards of installation, refurbishment, safety and cabling in force and applicable to the surfaces and/or brackets involved. In addition, the products may vibrate and damage the brackets onto which they are mounted. For this reason, the installation operations must be performed by a qualified professional who is familiar with installation and safety standards. Focal does not provide any end-of-use warranty for a given bracket or installation, as installing the loudspeakers is the customer’s sole responsibility. Focal is therefore not liable in any capacity whatsoever in the event of incident, accident and/or any other result or damage of any kind related to the installation of loudspeakers.
To facilitate the Focal-JMlab warranty, it is now possible to register your product online at: www.focal.com/warranty
Thank you for purchasing a Focal product. Welcome to our High-Fidelity world.
Our values are innovation, tradition, excellence and pleasure; our one and
only aim is to bring you a sound that is rich, pure and true. To get the most
out of
your product, we recommend that you read the instructions in this booklet,
then store it in a safe place to refer to in the future if needed.
Important recommendations
First of all, check the space available for fitting the speaker drivers (refer
to the plans on the packaging) then proceed with the cutting required. If
mounted in the factory location, check that there is sufficient space between
the speaker driver and the protective grille.
- Keep the speaker drivers clear of any metal shavings and dust particles during the cutting process.
- Clean thoroughly before fitting the speaker drivers.
- Ensure that there are no objects positioned across the grille, as this could damage the speaker drivers.
Choosing an amplifier
It is not an excess of amplifier power that can damage your loudspeaker and
drivers, but rather a lack of power. It is recommended to use an amplifier
that delivers 20% more power than the system’s total power to avoid a surge or
damage to the products. Your dealer will be able to guide you, depending on
your tastes and budget. Ensure that you follow the recommendations for your
amplifier in order to correctly connect each product from the K2 Power line.
Pre-installation wiring
You will only be able to begin fitting your products once you have connected
them using the terminal block on the speaker drivers (fig. 1, 2). We recommend
using a cable with a marker to ensure the polarity of the speaker drivers is
respected (+/-).
Bi-amplification cabling
In a bi-amplified 2-way kit (4-channel amplifier), make sure you follow (fig.
3, 4). In a bi-amplified 3-way kit (4-channel amplifier), make sure you follow
(fig. 5, 6, 7).
Installation
Please use suitable screws to avoid damaging your sub, your vehicle trim or
any of its other components (fig. 8).
Loudspeaker positioning
The loudspeakers in the range have been designed to deliver the most faithful
sound reproduction for any style of music. Nonetheless, a few simple rules
should be followed to optimise their performance and to guarantee good tonal
balance and a realistic sound image.
SUB 25 KXS / SUB 25 KXE / SUB 30 KXE
It is essential that the subwoofer is contained within an enclosure of
suitable dimensions, to create an appropriate internal volume that will
maximise the performance of the selected speaker driver (fig. 18). Please use
suitable screws to avoid damaging your sub, the floor of your vehicle or any
of its other components (fig. 20). Connect your subwoofer to the amplifier
using the terminal block located on the side of the speaker driver (fig. 20).
Ensure that the subwoofer is pointing towards an open space in order to
achieve the best performance.
SPECIAL PRECAUTIONS
Maintenance
To look after the K2 Power speaker drivers, simply dust using a dry cloth. If
the grille is marked, we recommend that you use just a damp cloth. Never use
solvents, detergents, alcohol or corrosive products, scrapers or scouring
utensils to clean the surface of the speaker drivers.
For the purposes of improvement or to take into account any legal or
regulatory changes, FOCAL-JMLab reserves the right to modify the technical
specifications of its products without prior notice. Where required, any
images shown are for illustrative purposes only, and may differ slightly from
the products sold.
Running-in period
The speaker drivers used are complex mechanical components that require a
running-in period to operate at their best.
This running-in period varies depending on the conditions in question and may
take several weeks. To reduce this time, we recommend operating your speaker
drivers for about 20 hours at a moderate volume. Once the speaker drivers’
characteristics have fully stabilised, you will be able to enjoy the
performance of your K2 Power products to the full. Warranty terms and
conditions
All Focal loudspeakers are covered by guarantee drawn up by the official Focal
distributor in your country. Your distributor can provide all details
concerning the conditions of guarantee. Guarantee cover extends at least to
that granted by the legal guarantee in force in the country where the original
purchase invoice was issued.
Correct elimination of this product.
This marking indicates that within the EU this product should not be disposed
of with other household wastes. To prevent any risk to the environment or
human health, please recycle them responsibly to encourage the reuse of
material resources. To return your used device, please use the return and
collection systems available, or contact the retailer where you purchased the
product. They can recycle this product safely.
Scan QR code for information on packaging disposal
http://www.focal.com/warranty/
Please note that for the ES 100 KE, ES 165 KE, ES 165 K2S, ES 165 K2E kits, the actual shape of the accessory is as follows:
We inform you that in the ES 165 KX3E kit, a midrange/tweeter stand is included among the accessories.
ES 165 K2E
Product Sheet
The fourth generation of K2 Power kits, with their emblematic aramid fibre cone, remain true to the precious and distinctive K2 DNA. The speaker drivers combine performance, power and style, whilst including patented innovations to deliver the very best. Designed, developed and manufactured in our workshops in France, the 2-way component kit ES 165 K2E takes in-car listening to another level.
Key points
- Made in France in the Focal workshops
- K2 Cone
- Robust design and high quality materials
- Exceptional power handling
- Aluminium grilles included
Type | 2-way component kit |
---|---|
Maximum power | 200W |
Nominal power | 100W RMS |
Sensitivity (2.83V/1m) | 93dB |
Frequency response | 60Hz – 22kHz |
Impedance | 2Ω |
Cone | K2 Sandwich |
Woofer | 6 1/2 ” (165mm) |
Voice coil diameter | 1 1/4 ” (32mm) |
Depth | 2 7/ 8 ” (74mm) |
Magnet | Ferrite |
Surround | TMD® |
Tweeter | ‘M’-profile |
Crossover | 6-12/12dB (3.5kHz) |
ES 165 K2E
Technical Sheet
Woofer 6 1/2 “
SPECIFICATIONS
Nominal power | 100W |
---|---|
Maximum power | 200W |
Sensitivity (2.83V/1m) | 92 8dB |
Cone | K2 Sandwich |
Nom. impedance | 20 |
Surround | Butyl |
DC resistance | 1.80 |
VC diameter | 32mm 1 |
Former | Kapton |
Layers | 2 |
Wire | CCAW |
Magnet (dxh) | 95x2Omm |
Net weight | 1450g |
FREQUENCY RESPONSE/IMPEDANCE
PARAMETERS
Rdc | 1.8Ω |
---|---|
Fs | 67Hz |
Mms | 13g |
Cms | 0.41mm/N |
Vas | 10l |
Qts | 0.55 |
Qes | 0.6 |
Qms | 7 |
Bxl | 4.2 N/A |
Sd | 128.6cm 2 |
SPL | 89.8dB |
Xmax | 4.8mm |
MECHANICAL DRAWING (MM)
Focal® is a trademark of Focal-JMLab® – www.focal.com – SCCG – 29/09/2023 – v1
References
- Top-of-the-range speakers and hi-fi equipment | Focal
- Top-of-the-range speakers and hi-fi equipment | Focal
- Se connecter à focal-naim
- Top-of-the-range speakers and hi-fi equipment | Focal
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>