newman MAN-0008-B simpleABI Cuff Link Systems User Guide
- June 16, 2024
- Newman
Table of Contents
newman MAN-0008-B simpleABI Cuff Link Systems User Guide
The ABI with Toe Examination with simpleABI Cuff-Link™ Systems
Please Read the User Manual first: This is a quick reference guide
Contraindications: Do not perform the exam on someone suspected of having
acute deep venous thrombosis, and do not take an arm pressure in an arm with a
shunt or dialysis graft.
Background: The ABI with Toe exam is typically performed after an ABI has
been done, especially if the larger ankle arteries appear to be incompressible
(pressure over 200mmHg) or anytime more information is needed about small
vessel disease. The ABI with Toe is done using the PPG probe. The patient is
supine and rested in a warm room.
The ABI with Toe Procedure
Opening the exam On the computer desktop, double click the simpleABI icon. When the program opens select FileNewNew ABI with Toe Report. The report will open and you can enter patient information, risk factors, symptoms, ICD codes, etc.
Attaching cuffs Wrap appropriate cuffs at each site. Attach the hoses from the Cuff-Link control unit to cuffs as shown below. The green connectors go to the arm cuffs and yellow to the ankles or toes. White hoses go to the patient’s right side, blue to the left.
Opening a previous exam If you have performed a previous ABI Exam, you may load the results into this exam by selecting FileLoadABI with Toe Report and selecting the ABI Exam you previously performed.
Brachial Pressure
- Begin with the right brachial. Place the Doppler probe at a 45 degree angle to the skin over the radial or brachial artery. Use plenty of gel and slowly move the probe laterally until the best signal is obtained. (You may also use the PPG sensor to listen for the pulse. If using the PPG, place the sensor on the fleshy part of the finger opposite the fingernail. Wait for consistent beeps from the system.)
- Press and hold Inflate on the Cuff-Link Remote (shown above) and inflate the cuff until you no longer hear the signal – continue for an additional 10-20 mmHg.
- Release Inflate and the cuff will automatically deflate at the suggested rate of 2mmHg/second.
- When you hear the Doppler signal return, pressing Pressure will be store the pressure value in the exam.
Ankle Pressures
- Press Next on the remote and the system will move to the Dorsalis Pedis (DP) site. Find the arterial signal using the Doppler probe on the dorsalis pedis artery on top of the foot. Obtain the arterial pressure in the same manner you did on the arm. (Hold Inflate until occlusion, release Inflate, press Pressure on Doppler signal return).
- Press Next and the system will move to the posterior tibial (PT) site. Find the Doppler signal on the posterior tibial artery. Obtain the arterial pressure. (Hold Inflate until occlusion, release Inflate, press Pressure on Doppler signal return).
Ankle Waveform
- Press Next and the system will move to the waveform site. Press and release the button with the Waveform image on the top right of the remote. The cuff will inflate to roughly 85mmHg and deflate to the proper pressure (65mmHg) and hold that while the waveform is obtained. The waveform will start to appear when the cuff has reached 65mmHg. The patient should remain as still as possible during the measurement.
The ABI with Toe Procedure (continued)
Toe Pressure
Press Next on the remote and the system will move to the Toe pressure field.
Place the PPG sensor on the fleshy part of the toe opposite the toenail. Use
cohesive tape or double sided tape to attach PPG sensor to the toe. Wait for
consistent pulsatile waveform to appear. A warm towel aids blood flow in the
toes. Obtain the toe pressure by inflating the cuff until the PPG waveform
‘flatlines’ and release Inflate. When pulsatile waveform reappears, press
Pressure to store the pressure value in the exam. Note The toe cuff inflates
rapidly – light taps of the Inflate button are best.
Toe Waveform
- Press Next and the system will move to the waveform site. Press and release the button with the Waveform button on the top right of the remote. The PPG waveform will begin to scroll in the waveform field. When you are satisfied with the waveform press either the Next or the Waveform button to store the PPG waveform. Patient should remain as still as possible during the measurement.
Left Side
- Repeat the above pressures and waveform sequence for the left side of the patient.
When finished, save or print the exam.
Helpful Hints
- Cuff techniques:
- Wrap the cuff snugly.
- Cuffs may be placed over thin clothing or stockings.
- Don’t let the patient try to help by lifting their leg – as they relax their muscles the cuff will become loose.
- Placing a pillow under the patients heels may aid the examination.
- Have the patient remain as still and quiet as possible while taking the waveforms.
- If the patient has tremors that interfere with the waveform, having them perform a few dorsiflexions with their toes before taking the waveform may help.
Doppler techniques:
- Hold the probe like you would a pencil, close to the end.
- Move the probe back and forth laterally over the artery to obtain the best signal.
- Support the probe with your hand resting on the patient so that the probe does not move as the cuff is inflated and deflated.
- One of the keys to a successful exam is being able to keep the probe in place as you inflate and deflate the cuffs.
- If the probe moves, you may not be able to hear the Doppler sounds return and may have to repeat the inflation.
Exam hints:
- A warm toe is a big help. Keep the toe covered if you can with a towel, even a warm towel if available Let the patient rest and relax before inflating the cuffs. Anchor the cord from the PPG sensor to the foot with some adhesive tape.
- Toe pressures are difficult to obtain in patients with small vessel disease. Pressures can be obtained with the Doppler probe as well but it is more difficult as the digit arterial signal is hard to locate.
Cuff-Link Control Unit with tubing properly attached
PPG
PPG & cuff on Toe
Toe Pressures using the DigiDop
- The Newman Medical DigiDop has proprietary software that enhances the PPG sounds and can make it easier to take the toe pressures in a TBI exam.
Toe Pressure
- Press Next on the remote and the system will move to the Toe site. Place the PPG sensor on the fleshy part of the toe opposite the fingernail. Using double sided adhesive tape to attach the sensor instead of wrapping it can help with the PPG signal since pressure on the sensor can diminish the PPG signal. Wait for consistent beeps from the system. A dark warm towel over the foot aids blood flow in the toes and shields the sensor from stray changes in the ambient lighting. Obtain the toe pressure in the same manner you did on the arm and ankles by inflating the cuff and listening for the return of consistent pulsatile signals. The toe cuff inflates rapidly – a light tap of the inflate is best. (Inflate until occlusion, release Inflate, press Pressure upon signal return)
Toe Waveform
- Press Next and the system will move to the waveform site. Press and release the button with the Waveform image on the top right of the remote. The cuff will inflate to roughly 85mmHg and deflate to the proper pressure (65mmHg) and hold that while the waveform is obtained. The waveform will start to appear when the cuff has reached 65mmHg. The patient should remain as still as possible during the measurement.
Left Side
- Repeat the above pressures and waveform sequence for the left side of the patient. When finished, save or print the exam.
Helpful Hints
- Cuff techniques:
- Wrap the cuff snugly.
- Cuffs may be placed over thin clothing or stockings.
- Don’t let the patient try to help by lifting their leg – as they relax their muscles the cuff will become loose.
- Placing a pillow under the patients heels may aid the PVR examination.
- Have the patient remain as still and quiet as possible while taking the waveforms.
- If the patient has tremors that interfere with the waveform, having them perform a few dorsiflexions with their toes before taking the waveform may help.
Doppler techniques:
- Hold the probe like you would a pencil, close to the end.
- Move the probe back and forth laterally over the artery to obtain the best signal.
- Support the probe with your hand resting on the patient so that the probe does not move as the cuff is inflated and deflated.
- One of the keys to a successful exam is being able to keep the probe in place as you inflate and deflate the cuffs.
- If the probe moves, you may not be able to hear the Doppler sounds return and may have to repeat the inflation.
Exam hints:
- A warm toe is a big help. Keep the toe covered if you can with a towel, even a warm towel if available Let the patient rest and relax before inflating the cuffs. Anchor the cord from the PPG sensor to the foot with some adhesive tape.
- Toe pressures are difficult to obtain in patients with small vessel disease. Pressures can be obtained with the Doppler probe as well but it is more difficult as the digit arterial signal is hard to locate.
Cuff-Link Control Unit with tubing properly attached
PPG wrapped on finger
PPG & cuff on Toe with tape
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>