Lucci 011810 Solis 1 Light Pendant Instruction Manual
- June 16, 2024
- Lucci
Table of Contents
Installation Instructions
SOLIS PENDANT
SKU# 011810, 011811
Rated Voltage 220-240V~ 50Hz
011810 Solis 1 Light Pendant
Thank you for purchasing this quality Lucci product. To ensure correct
function and safety, please read and follow all
instructions carefully before assembly, installation and use of this
luminaire. Please keep instructions for future reference.
Warranty
- This luminaire is covered by a 12 month warranty. The warranty is from date of purchase, not the date of installation.
- If the luminaire is not assembled and installed by a licensed electrician it will void the warranty.
- Please retain proof of purchase and evidence of installation by a licensed electrician for any warranty enquiries.
- Warranty will be void if there is any damage due to improper usage or modification to the luminaire.
- Failure to comply with the instructions in this manual may increase the risk of damage or injury and will void warranty.
Installation Requirements
-
Must be assembled and installed by a licensed electrician.
-
All wiring and installation of the luminaire must adhere to the latest local and national wiring rules. eg. AS/NZS 3000 Electrical Installations.
-
This luminaire is a Class II product and must be maintained during wiring and installation.
-
Do not exceed the maximum wattage rating.
-
Select a suitable location for installation:
– This luminaire is suitable for indoor use only.
– The mounting point must support 2 times the weight of the luminaire.
– Ensure the luminaire is not installed in direct line of an air vent/system.
– When installing a luminaire in an area prone to moisture, ensure that the area is well ventilated and an appropriately rated exhaust fan is used if required. Damage or corrosion caused by moisture is not a product fault, and as such is not covered under warranty. -
Take care not to pull any electrical wires during unpacking as this may damage the connection.
-
Lay out all the components on a smooth surface and make sure there are no components missing before assembling. If parts are missing, return the complete product to the place of purchase for inspection or replacement.
-
Check whether the luminaire has been damaged during transport. Do not operate/install any product which appears damaged in any way. Return the complete product to the place of purchase for inspection, repair or replacement.
Installation Directions
- Remove all packaging material from the product and be careful not to throw away accessories that may be hidden within the packaging material. If assembly is required, place the luminaire on a smooth non-scratch surface.
- Ensure power to the circuit you are working on has been switched OFF before commencing any electrical work. (Fig A)
- Loosen the canopy cover plate from the mounting bracket by rotating it anti-clockwise. (Fig B-1)
- Loosen the 2 screws from the mounting bracket cover. (Fig B-2)
- Use the mounting bracket as a template to mark the screw positions on the ceiling. (Fig B-3)
- Pull the supply wire down from the ceiling and through the mounting bracket hole. (Fig B-4)
- Install the mounting bracket onto the ceiling by using appropriately sized mounting screws and anchors. Ensure the screws and anchors used are suitable for the mounting surface and the surrounding environment. (Fig B-5)
- Connect the mains supply wire to the terminal block. Ensure the wires are secure and no bare wires are exposed. (Fig B-6)
Mains Supply Wire
Neutral – Blue or Black
Live – Brown or Red| Luminaire Wire / Terminal Block
Blue or N
Brown or L
---|--- - Install the mounting bracket cover back onto the mounting bracket. (Fig B-7)
- Secure the mounting bracket cover by tightening the 2 screws. (Fig B-8)
- Install the canopy cover plate over the mounting bracket by rotating it clockwise. (Fig B-9)
- Remove the lamp skirt from the lamp holder by rotating it anti-clockwise. (Fig B-10)
- Remove the glass shade from the luminaire. (Fig B-11)
- Install the glass shade onto the lamp holder. (Fig B-12)
- Secure the glass shade by installing the lamp skirt back onto the lamp holder. (Fig B-13)
- Install a globe (not included) into the lamp holder. Do not exceed the maximum wattage rating. (Fig B-13)
- After the installation, switch on the luminaire to test all the lighting functions and enjoy your new luminaire. (Fig C)
Safety Tips
- Always ensure the power is OFF and the luminaire has cooled down before performing any maintenance, cleaning, changing the globe or making any adjustment to the luminaire.
- To avoid injury or damage to the luminaire, ensure that power leads and screws are secure before connecting the power.
- Select a suitable location away from liquids and hazards.
- To clean, wipe with a soft damp cloth. Do NOT soak or immerse the luminaire in water or other liquids.
- Ensure that the luminaire does not come in contact with corrosive chemicals/solvents or abrasive cleaners etc.
Specifications
| SKU # | 011810 | 011811 |
|---|
Art No.
|
203826
|
204297
Colour| Black| White
Insulation Class| Class II
Rated Voltage| 220-240V~ 50Hz
Rated Wattage| Max. 45W
Lamp Holder| ES / E27
Weight| 1.6kg
Canopy Dimensions| H:38mm Dia:126mm
Product Dimensions| H:375mm Dia:190mm Susp:2000mm
v 1 . 1 ( 1 1 / 2 0 1 9 )
Documents / Resources
|
Lucci 011810 Solis 1 Light
Pendant
[pdf] Instruction Manual
011810, 011811, 011810 Solis 1 Light Pendant, Solis 1 Light Pendant, 1 Light
Pendant, Light Pendant, Pendant
---|---