ICSTATION RDA5807 FM Radio Kit User Manual

ICSTATION RDA5807 FM Radio Kit

Product Information

Specifications

• Product Name: RDA5807 FM 87-108MHz Radio Receiver LCD1602 DIY Kit
• Work Voltage: DC 4.5V~5.5V
• Output impedance: 4ohm
• Output power: 5W
• Output channel: Mono
• Receiver Frequency: 87.0MHz~108.0MHz
• Frequency accuracy: 0.1MHz
• Equivalent noise: >=30dB
• Work Temperature: -40~85
• Work Humidity: 5%~95%RH
• Size (Installed): 907055mm

Feature

• Built-in volume adjustment
• RGB spectrum indicator flashing automatically
• Support 87Hz-108MHz receiver frequency
• Built-in 5W power amplifier
• LCD1602 display screen

Component Listing

Product Usage Instructions

Use Methods

1. Press the left button to turn ON/OFF power supply.
2. Press the right button to turn ON/OFF the spectrum indicator.
3. Press S+ or S- to adjust volume.
4. Press P+ or P- to adjust receive frequency and FM station.

Installation Tips

1. User needs to prepare the following tools:
   • Soldering iron (Rosin core radio solder)
   • Wire cutters
   • Wire strippers
   • ‘+’ Screwdriver
2. Please be patient until the installation is complete.
3. The package is a DIY kit. It needs to be installed by the user.
4. The soldering iron should not touch the components for a long time (1.0 second).

FAQ

• Q: What is the purpose of this product?
  A: This product can be used for training welding skills, student school projects, DIY production, project design, electronic competitions, gift giving, crafts collection, home decoration, souvenir collection, graduation design, and holiday gifts.

• Q: Can I use this product in an environment with signal interference?
  A: No, this product is a wireless module and should not be used in an environment with signal interference.

• Q: Are there any special considerations during installation?
  A: Yes, there is a SMD component that needs to be placed on the PCB and fixed by tin.

FM Radio Kit Soldering Project LCD1602

Introduction

It is an RDA5807 87.0MHz-108.0MHz Wireless FM Radio Receiver DIY Kit with RGB spectrum indicator flashing automatically.It has a blue LCD1602 display screen which can clearly display the receiving frequency.

Feature

1. Built-in volume adjustment
2. RGB spectrum indicator flashing automatically
3. Support 87Hz-108MHz receiver frequency
4. Built-in 5W power amplifier
5. LCD1602 display screen

Parameter

1. Product Name:RDA5807 FM 87-108MHz Radio Receiver LCD1602 DIY Kit
2. Work Voltage:DC 4.5V~5.5V
3. Output impedance:4ohm
4. Output power:5W
5. Output channel:Mono
6. Receiver Frequency:87.0MHz~108.0MHz
7. Frequency accuracy:0.1MHz
8. Equivalent noise: >=30dB
9. Work Temperature:-40℃~85℃
10. Work Humidity:5%~95%RH
11. Size(Installed):907055mm

Use Methods:

1. Press left button to turn ON/OFF power supply.
2. Press right button to turn ON/OFF spectrum indicator.
3. Press S+ or S- to adjust volume.
4. Press P+ or P- to adjust receive frequency and FM station.

Component Listing

Note :Users can complete the installation according to the PCB silk screen and component list.

Schematic Diagram

Application:

1. Training welding skills
2. Student school
3. DIY production
4. Project Design
5. Electronic competition
6. Gift giving
7. Crafts collection
8. Home decoration
9. Souvenir collection
10. Graduation design
11. Holiday gifts

Note

1. It is a wireless module. So do not use it in an environment with signal interference.
2. There is a SMD component so that you can place it on PCB and then fix by tin.

Installation Tips:

1. User needs to prepare the welding tool at first.
2. Soldering iron (<50 Watt)
3. Rosin core (“radio”) solder
4. Wire cutters
5. Wire strippers
6. + ’ Screwdriver
7. Please be patient until the installation is complete.
8. The package is DIY kit.It need finish install by user.
9. The soldering iron can’t touch the components for a long time(1.0 second), otherwise it will damage the components.
10. Pay attention to the positive and negative of the components.
11. Strictly prohibit short circuit.
12. User must install the LED according to the specified rules.Otherwise some LED will not light.
13. Install complex components preferentially.
14. Make sure all components are in right direction and right place.
15. It is strongly recommended to read the installation manual before starting installation!!!
16. Please wear anti-static gloves or anti-static wristbands when installing electronic components.

Installation Steps(Please be patient install!!!)

1. Step 1 : Install 1pcs SMD components RDA5807 FM Receiver at U2. Verify and confirm the installation direction of RDA5807. The rectangular silk screen on the PCB coincides with the crystal oscillator on the RDA5807 to locate the installation direction.
2. Step 2 : Randomly choose a pad on the PCB, and then melt the solder on this pad.
3. Step 3 : Fix RDA5807: Use a soldering iron to melt tin on the pad just now and hold RDA5807 with tweezers in the other hand to place/press on U2 to prevent movement. Take care to match and align each pads. Then remove soldering iron. Then remove tweezers after solder tin coolina and solidification.
4. Step 4 : Connect others pads on RDA5807 to pads on PCB by tin and soldering iron.
5. Step 5 : Install 1pcs 100hm Metal Film Resistor at R6.
6. Step 6 : Install 2pcs 1000hm Metal Film Resistor at R19, R20.
7. Step 7 : Install 2pcs 6.8Kohm Metal Film Resistor at R12, R15.
8. Step 8 : Install 4pcs 1Kohm Metal Film Resistor at R9, R13, R16, R17.
9. Step 9 : Install 11pcs 10Kohm Metal Film Resistor at R1-R5,R7,8,11,R14, R15, R18.
10. Step 10 ; Install 3pcs DO-41 1N4007 Diode at D11,D12, D13. Pay attention to the installation direction. There is a black mark on 1N4007 and a white mark on PCB which are used to confirm the installation direction.
11. Step 11 : Install 1pcs 11.0592MHz Crystal Oscillator at Y1.
12. Step 12 : Install 1pcs DIP-8 IC Socket at U3. There is a gap mark on one end of the IC Socket and there is a gap mark on PCB silk screen where the IC Socket can place on. These two marks are corresponding to each other and are used to specify the installation direction of the IC Socket.
13. Step 13 : Install 1pcs DIP-40 IC Socket at U1. There is a gap mark on one end of the IC Socket and there is a gap mark on PCB silk screen where the IC Socket can place on. These two marks are corresponding to each other and are used to specify the installation direction of the IC Socket.
14. Step 14 : Install 2pcs 22pF Ceramic Capacitor at C1,C2.
15. Step 15 : Install 3pcs 0.1uF 104 Monolithic Capacitor at C10,C12, C13.
16. Step 16 : Confirm and identify the installation direction of the KA2284.
17. Step 17 : Install 2pcs ZIP-9 KA2284 LED Driver at KA2284.
18. Step 18 : Identify the positive(anode) and negative(cathode) lead of LED. The leads of the LED must be installed correctly, otherwise the LED cannot be turned on. Here are four methods as following
19. According to the length of the LED lead to distinguish. The longer pin is positive(anode) lead. The shorter pin is negative(cathode) lead.
20. Identify the negative(cathode) of the LED is to look into the plastic case where one can see that the negative(cathode) is much thicker/bigger inside the plastic case than the anode lead.
21. Identify by edge of plastic case. The negative(cathode) lead of the LED shoul be the pin nearest the flat on the plastic case.
22. Test by 3V battery or multimeter. The pin is positive(anode) lead which has connect to positive of 3V if LED can light up after connect 3V power supply. (LED can not be powered directly from 3V for a short time: less then 0.5second)
23. Note: If the flat on package disagrees with other indicators(short lead, large cathode lead end), then other indicators take priority. I.e. if the flat disagrees with the lead length,use the lead length as the cathode indicator.
24. Step 19: Install 10pcs 5mm RGB LED at LED1-LED10.
25. Step 20 : Install 1pcs 16Pin DuPont Female Socket at LCD1602.
26. Step 21 : Bend the pins of only one 4.7uF electrolytic capacitor about 2mm. Note:Just for only one!
27. Step 22 : Install this Electrolytic Capacitor at C7 Pay attention to distinguish between positive and negative. The Longer pin is positive pole. Note: The capacitor needs to be placed horizontally. Otherwise, the following components cannot be installed.
28. Step 23 : Install others 8pcs 4.7uF Electrolytic Capacitor at C3, C5, C6, C8, C11, C14, C15, C16 Pay attention to distinguish between positive and negative. The Longer pin is positive pole. Note: The capacitor needs to be placed horizontally, keep a distance of 2mm between the capacitor and the PCB when installing.
29. Step 24 : Install 2pcs 100uF Electrolytic Capacitor at C4,C9. Pay attention to distinguish between positive and negative. The Longer pin is positive pole. Note: The capacitor needs to be placed horizontally, keep a distance of 2mm between the capacitor and the PCB when installing.
30. Step 25 : Install 1pcs DC-005 Power Socket at J1.
31. Step 26 : Install 2pcs 5.8*5.8mm Self-locking Button at S4, S6.
32. Step 27 : Install 4pcs 6620mm Black Button atS1,52,S3,S5.
33. Step 28 : Install 1pcs DIP-8 IC LM386N at U3. There is a gap mark on one end of the IC and there is a gap mark on DIP-8 IC Socket where the IC can place on. These two marks are corresponding to each other and are used to specify the installation direction of the IC.
34. Step 29 : Install 1pcs DIP-40 IC STC89C52RC. There is a gap mark on one end of the IC and there is a gap mark on DIP-40 IC Socket where the IC can place on. These two marks are corresponding to each other and are used to specify the installation direction of the IC.
35. Step 30 : Fix 4pcs M310mm Copper Pillar and 4pcs M38mm Screw on PCB.
36. Step 31 : Install 1pcs 16Pin Male Socket on the back of LCD1602 display screen. Note the black plastic block on the back of the LCD.Please cut off the extra pins with scissors and reserve the 16pin, if you get 20pin or 22pin or other.
37. Step 32 : Plug LCD1602 display screen on 16Pin DuPont Female Socket. Note: Don’t use screws to fix it for now.
38. Step 33 : Install 1pcs 750hm Antenna at ANT. Keep a distance more than 5mm from PCB and fix by tin(not screw). Note that the antenna should be installed on the back of the РСВ
39. Step 34 : Place 2pcs red button cap on Self-locking Button.
40. Step 35 : Connect speaker to PCB at SP by 20cm red/black Cable. The speaker does not distinguish between positive and negative.
41. Step 36 : Tear off the protective film on the surface of the acrvlic shell.
42. Step 37 : Fix Top Acrylic Board and LCD1602 Acrylic Board on Copper Pillar by 4pcs M3*6mm Screw.
43. Step 38 : Fix 4pcs Side Acrylic Board by 6pcs M3*6mm Screw and 6pcs M3 Nuts.
44. Step 39 : Fix speaker on Acrylic Bottom Board by 4pcs M3*10mm Screws and 4pcs M3 Nuts.
45. Step 40 : Install Speaker Acrylic Board by 4pcs M3*6mm Screw and 4pcs M3 Nuts.
46. Step 41 : Connect to power supply and enjoy the effect.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>