MOUSETRO ZN-S05 Smart Door Lock User Manual
- June 16, 2024
- MOUSETRO
Table of Contents
MOUSETRO ZN-S05 Smart Door Lock
Product layout
Please keep internal/external panel clean before installation.
Packing List
Panel and lock body installation
- Use the hole adaptor to make door holes according to the size instruction. Adjust center distance of lock body to 60mm or 70mm (factory setting is 60mm).
- Confirm the direction of latch bolt according to the way of opening the door. Insert the lock body into the hole of door and tighten it with screws.
- Adjust the handle direction according to your door open direction.
- Unscrew the 4 locking screws on the lower plate of the front plate and take down the mounting plate.
- Unscrew the reversing screw and adjust the direction of handle as needed, tighten the reversing screw after adjusting in place. Press the handle a few times to ensure it is smooth, then screw back the mounting screws on the lower plate of the front plate.
- Unscrew the inner panel mounting screws 3.
- Unscrew the reversing screw and adjust the direction of handle as needed, tighten the reversing screw after adjusting in place. Press the handle a few times to ensure it is smooth.
- According to the direction of the handle to choose the direction of the small dot. Toggle small dot and handle in the same direction, handle in the left toggle small dot in the left, handle in the right toggle small dot in the right.
- After door handle reversal is complete, put mounting studs type 1 and type 2 onto the front panel.
- Cut the square spindle according to the door thickness. Insert the square spindle from the outside of the door into the square hole of the lock body ( as picture shows to install ). The dot side faces the outside of the door. Take the main connecting cable above through lock body to inner panel, put dot side of square spindle into front panel, and make front panel close to the door surface.
- Fix the inner plate onto the inside door surface by using 3pcs mounting screws. Adjust the front panel and assemble screw bolt to make the panel vertical, then tighten inner plate with screws.
- Tuck the spring into the square hole in the inner panel (as picture shows ).
- Plug the data cable into the inner panel main line interface.
- Note the spring in the square hole of inner panel and insert the square spindle into that square hole. Then install the inner panel assembly to the inner mounting plate, screw on 2 mounting screws until the panel can be moved with a little force. Trigger the front and inner handles, if the latch is not smooth, then adjust the panel. If the latch can move smoothly, tighten the panel mounting screws.
- Install batteries and the battery cover. Check all electronic functions and verify the mechanical key to unlock. If all functions are normal, you can register an account and use your smart lock.
Product Features
(According to actual model):
- Open Way: Fingerprint, password, IC card, mechanic key, Bluetooth, and etc. Bring new experience to open the door.
- Fingerprint: Advanced semi-conductor sensor, 360 degrees identification angle. Effective fingerprint recognition(FRR<3%, FAR<0.01%).
- Password: Advanced touch technology, which allows to put 1-12 digit numbers before and after true password.
- Capacity: Fingerprint 100pcs, password 100pcs, card 100pcs (Total 250pcs mixed freely)
- Membership management: The administrator has the highest rights to edit and set (users can only lock and unlock the door).
- Alarm function: Low power alarm, password protection alarm
- External power supply: Please use power source or other equipment which is 5V to recharge for emergency when low power(Replace new battery once door is open.
Remark
- Please reset factory default and clear all member records immediately after the lock is installed
- Please use different and more angle when input fingerprint, Do attention to do with no hard.
- We suggest to change battery at least in 6 months period, in order to avoid smart lock damage because of exhausted battery.
- The lock uses 4*AA alkaline batteries. When first time alarms “low battery, please replace battery”, it can be open around 50 times. But please replace batteries immediately in order to avoid any inconvenience.
- By continuous 5 times wrong input with fingerprint/password/card, the lock will be alarmed and locked for 90 seconds.
Guide And Bluetooth connecting
Guide
- Reset factory setting: Unlock with any fingerprint, password or IC card before Bluetooth connected.
- Unlock/lock: Use mobile, fingerprint, password or IC card to open when outdoor. Use unlock/ lock button to open when indoor.
- Bell function: press “ ” when screen is on.
- Reset factory mode( two ways ):
- Press ” factory reset ” button
- Remove the device from APP, lock will be reset factory automatically.
Bluetooth connecting ( two ways )
Click “+” on the upper right corner in APP
Manual addition method:
- Click “Camera/lock” category on the left
- Search “Door Lock (Bluetooth)”
- Start Bluetooth network connection.
- In 3rd page, waiting for device connecting.
Automatic search method:
- Select device search page
- Search the lock automatically in the page of APP
- Click on the link, and waiting for device connection
- Bluetooth: In App page, slide right to unlock, slide left to lock
- Fingerprint: Click membership administration in APP, scan fingerprint according to tips, then you may use scanned fingerprint to open.
- Password: Click membership administration in APP, input password, then you may use input password to open.
- IC card: Click membership administration in APP, scan IC card, then you may use IC card to open.
- Automatic lock: On App page, slide down to setting with auto-lock on/off. The door will be automatically closed in 6 seconds when auto-lock function is on.
- Volume: In APP page, slide down to set volume with mute, low, normal and high.
- Lock Button: Lock button on inner panel. Only master user is allow to open the door when lock button function is on. Push down to turn off lock function.
QR code
- Please scan the QR code with your cell phone camera to watch the installation video.
- Following the video guide to install may avoid most installation troubles.
App download
App page
App registration: please register new account or use sms password to enter APP. If you do not have an account, Click “new account” to register, following steps, to get sms, and new password setting. Or go ahead to enter APP directly with exist account. Login way includes password, verifying password by sms, social account.
Technical
Email: support@mousetro.net
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>