NICENT RF012Q Adjustable Bed Frame User Manual

NICENT RF012Q Adjustable Bed Frame User Manual

Product Information

Specifications

• Remote Control Range: 16 feet (5 m)
• Available Buttons on Remote Control:
  • Under Bed Light: Turn the under bed light on and off
  • Head UP/DOWN and Foot UP/DOWN: Move the head and foot platforms up and down
  • Sleeping Position: Move the bed frame to a saved memory position
  • Memory Position: Move the bed frame to a saved memory position
  • Massage mode, Massage motor off, and Massage motor intensity UP/DOWN: Change the massage mode, turn massage mode off, and adjust the intensity

OPERATION

Product Usage Instructions

Remote Control Usage

The Adjustable Bed Frame comes with a Remote Control that allows you to operate the bed frame from a distance of 16 feet (5 m). The specific Remote Control supplied with your product may vary depending on the model you have ordered. The Remote Control includes various buttons for different functions:

**Note:

** The Remote Control supplied with your product may vary.

Important Notices and Cautions

Notice: Pressing too many buttons in a short space of time can cause damage to the system. Wait for at least one second between pressing different buttons.
Caution: Misuse of the Remote Control by children could lead to minor or moderate injury. Activate the Child Lock when children are present. In Sync Mode, ensure the Child Lock feature is activated on both Remote Controls. Do not allow children to play with the Remote Control.
Caution: Multiple Bed Frames may be in range of your Remote Control. Operating the wrong Bed Frame may lead to minor or moderate injury. Ensure the Remote Control is paired to the correct Bed Frame. Ensure the Remote Control has been safely unpaired before using it on another Bed Frame.

Pairing the Remote Control
You need to pair the Bed Frame to a Remote Control before operation. Follow these steps:

1. Ensure the Bed Frame has been unplugged for at least 10 seconds.
2. Plug the Bed Frame into the mains. This will automatically switch it to Pairing Mode for 30 minutes. During this time, the Bed Frame will search for Remote Controls to be paired with.
3. While in Pairing Mode, press and release any button on the Remote Control. This will pair the Remote Control to the Bed Frame.

• Activate the Child Lock when children are present
• In Sync Mode, ensure the Child Lock feature is activated on both Remote Controls
• Do not allow children to play with the Remote Control

CAUTION
Risk of minor or moderate injury
Multiple Bed Frames may be in range of your Remote Control. Operating the wrong Bed Frame may lead to minor or moderate injury.

• Ensure the Remote Control is paired to the correct Bed Frame
• Ensure the Remote Control has been safely unpaired before using it on another Bed Frame

Unpairing the Remote Control

1. Press and hold the Head UP and Foot DOWN Buttons on the Remote Control for at least 10 seconds.
2. Test the Remote Control to check that it has been safely unpaired.

Reference Drive

Before using the Bed Frame for the first time, you must perform a reference drive.When the drive is initiated, the lower section of the bed will move first, followed by the upper section.

To perform the reference drive, follow these steps:

1. Press and hold the Head UP/DOWN, Foot UP/DOWN, or Sleeping Position Button on the Remote Control. The lower part of the Bed Frame will begin the reference drive. It will reach a lower limit and then move up slightly. Do not release the button.
2. Continuing to hold the button, wait for the upper part of the frame to complete the drive.
3. Release the button and use the Bed Frame according to the instructions. If the drive is interrupted, pressing any movement button restarts downward movement.

Moving the Bed Frame Up and Down

1. Press and hold the UP/DOWN Button for the platform you wish to adjust.
2. Wait until the Bed Frame has reached the desired position.
3. Release the UP/DOWN Button. The Bed Frame will move until the button is released or the highest/lowest position is reached.

Saving a Memory Position
There are two pre-saved Memory Positions: Anti-Snore (Position 1) and Zero Gravity (Position 2). Press the Memory Position Buttons on the Remote Control to move to these positions. You can change saved Memory Positions to new Memory Positions. To do this, proceed as follows: The Adjustable Bed Frame comes with two pre-saved Memory Positions: Anti-Snore (Position 1) and Zero Gravity (Position 2). To move to these positions, press the Memory Position Buttons on the Remote Control.

1. Press and hold the UP/DOWN Button for the Platform you wish to adjust
2. Wait until the Bed Frame has reached the desired position
3. Release the UP/DOWN Button
4. Press and hold the Button for the new Memory Position for at least 3 seconds to save the
5. Release the Memory Position Button.

If you want to save new Memory Positions, follow these steps:

Note:

These instructions assume that you have already moved the bed frame to your desired position.

1. Press and hold the Memory Position Button on the Remote Control that you want to save the new position to.
2. The bed frame will beep and the Memory Position Button LED will flash three times to indicate that the new position has been saved.

****FACTORY RESET

A Factory Reset restores the Bed Frame to the same state as before first use. Any memory positions you have stored will be deleted and replaced with the pre-set memory positions.

To perform a Factory Reset:

1. Press and hold the Foot DOWN and Head DOWN buttons for 10 seconds.
2. When the reset is complete, the Control Box will click twice.
3. Release the buttons.

To perform a Reference Drive after the Factory Reset, only release one of the DOWN buttons. This will start the Drive automatically.

MOVING THE BED FRAME TO A SAVED MEMORY POSITION
Proceed as follows to move the Bed Frame to a saved Memory Position:

1. Press the Memory Position Button for the Memory Position you wish to move to, then release.
2. Wait for the Bed Frame to move to the saved Memory Position

** MOVING THE BED FRAME TO THE SLEEPING POSITION**
The Sleeping Position is the Bed Frame’s lowest position. While in the Sleeping Position, all Platforms are horizontal.

Proceed as follows to move the Bed Frame to the Sleeping Position:

1. Press and release the Sleeping Postion Button (do not hold the Button)
2. Wait for the Bed Frame to move to the Sleeping Position

****ACTIVATING THE CHILD LOCK

Always activate the Child Lock when children are near the Bed Frame. Proceed as follows:

1. Press and hold the Head UP and Foot UP Buttons for at least 6 seconds.
2. The LED will flash 3 times to confirm. Test the Remote Control to check that Child Lock has been activated.

To disable Child Lock, repeat the steps above. If you remove the batteries from the Remote Control, the Child Lock will be deactivated automatically If you try to operate the Bed Frame while the Child Lock is activated, the LED will flash 6 times.

PERFORMING A FLAT POSITION RESET

To perform a Flat Position Reset:

1. Press the Sleeping Position Button for at least 10 seconds.
2. The Control Box clicks twice to confirm theinput.
3. Perfom a Reference Drive with the Sleeping Position Button or any UP/DOWN Button (see section “Reference Drive”).

UNDER BED LIGHT
To turn Under Bed Light on and off press the Under Bet Light Button

USB PORTS
To charge your mobile phone, plug the cable into the USB socket on the edge of the platform.

MASSAGE

1. To turn on the massage, press one of the intensity buttons. Press + to increase the intensity, and – to decrease the intensity. There is a loop. When the maximum intensity is reached, pressing + again turns off the massage, and pressing + second time starts the massage with the lowest intensity. This also applies to pressing –
2. To change the massage mode, press this button.
3. Press this button to turn off the massage.

SYNC MODE

IMPORTANT
Sync Mode allows you to control two Bed Frames with one Remote Control. If you only have one Bed Frame continue reading at the next chapter.

Before configuring Sync Mode, please ensure:

• Both Bed Frames are standing next to each other
• The Bed Frames will not collide with each other when moving
• Each Bed Frame can be controlled using its own Remote Control

To activate Sync Mode:

• Ensure both Bed Frames have been disconnected from the Power Outlet.
• Connect the Control Boxes of the two Frames with the Sync Cable (X). This should be inserted into the port marked “SYNC” on each Control Box.
• Ensure the Cable is Routed so that it does not interfere with the movement of the Bed Frames.
• Reconnect the Bed Frames to the Power Outlet.
  • If the Bed Frames do not move together, disconnect from the Power and repeat the steps.
  • To end Sync Mode, disconnect the Sync Cable.
• MOVING THE BED FRAME UP AND DOWN IN SYNC MODE
  When Sync Mode is activated, pressing the UP/DOWN Buttons on either of the Remote
  Controls will move both Bed Frames simultaneously.

FIXING MISALIGNMENT

If two connected Bed Frames have different saved Memory Positions, pressing a Memory Position Button will cause the Bed Frames to move to different positions. This is called Misalignment. In this case, you must move both Bed Frames to their lowest position.

• Press the Sleeping Position Button on one Remote Control
• Wait for both Bed Frames to reach their lowest position
• The Bed Frames are realigned. Continue using the Bed Frame as normal.

This device complies with part 15 of the FCC Rules. Operation is subject to the condition that this device does not cause harmful interference (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmfu interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation.

If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

The device has been evaluated to meet general RF exposure requirement. The device can be used in portable exposure condition without restriction.

FCC ID: 2A2RI-RF012Q

This device complies with Industry Canada licence-exempt RSS standard(s).

Operation is subject to the following two conditions:

• This device may not cause interference, and
• This device must accept any interference, including interference that may cause undesired operation of the device.

FAQ

• Q: What should I do if the Remote Control buttons are not responding?
  A: First, check if the batteries in the Remote Control need to be replaced. If the batteries are fine, try unpairing and pairing the Remote Control again. If the issue persists, contact our customer support for further assistance.

• Q: How far can I operate the Bed Frame using the Remote Control?
  A: The Remote Control has a range of 16 feet (5 m), allowing you to operate the Bed Frame from a distance within this range.

• Q: Can I use one Remote Control for multiple Bed Frames?
  A: No, each Bed Frame needs to be paired with its own Remote Control. Using the wrong Remote Control with a Bed Frame may lead to potential injury.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>