baja designs S1 Electric Start Pit Bike Moto Kit Instructions
- June 4, 2024
- baja designs
Table of Contents
Electric Start Pit Bike Moto Kit
Instructions
LIMITED LIFETIME WARRANTY
Baja Designs proudly offers a LIFETIME WARRANTY against the manufacturer’s
defect on all the products that we manufacture.
These are comprehensive warranties; other than the exclusions below – you’re
covered. If your LEDor HID bulb burns out, you’re covered. Additionally,
cutting off our connector or changing your lenses does not automatically void
your warranty.
Exclusions: Installation errors, abuse, misuse, or crash damage. You must
be the original owner of the product and can supply proof of purchase. Baja
Designs manufactures its own products as well as resells products manufactured
by others. Baja Designs makes no express or implied warranties on products not
manufactured by Baja Designs including without limitation any warranties or
merchantability and fitness for a purpose. We will, however, pass on all
warranties made by the manufacturer, who has sole responsibility for
performing such warranties. Baja Designs will pay the freight if your product
is less than 90 days old, otherwise defective products must be returned to
Baja Designs, Inc., freight prepaid. At our option, we will repair or replace
the items in question and return them at no charge. If the identical product
is no longer available, we will replace it with a similar product of equal
value. Baja Designs Inc. will not be responsible for any indirect or
consequential damages in connection with defective merchandise. Items
purchased through a Baja Designs authorized dealer must be returned through
the dealer. Only available on LED auxiliary lights and the product must be in
sellable condition at MSRP. The product that has been damaged in any way after
the original purchase date will be excluded from this guarantee.
Indemnification
Buyer hereby acknowledges off-roading, racing, and driving at night are
dangerous activities and that the products and/or supplies purchased from Baja
Designs are used in an inherently dangerous activity that may endanger life
and limb; and in no event shall the seller, or seller’sheirs and assigns, be
held liable for consequential damages, nor shall seller’s liability on any
claim for damages arising out of or connected with the sale, delivery, or use
of purchased products and/or supplies exceed the purchase price of the
products and/or supplies
S1 Electric Start Pit Bike Moto Kit Instructions
Tools Required
– 7/16” wrench and socket
– Phillip’s head screwdriver
– 3mm and 4mm Allen Wrenches
Re-torque all the fasteners after 100 miles. our installation is now complete! Thank you for choosingBaja Designs.
- To begin, assemble the S1 light with the included standard bracket and hardware. The exploded view is on the right. Use the 7/16” wrench, 7/16” socket, and 3mm Allen wrench.
- Determine where the light can be mounted to the handlebars without interference from the controls. Turn the bars back and forth and compress and decompress the forks to make sure the light will not interfere with anything like the front brake cable.
- Locate the Included handlebar mount assembly. With the 4mm Allen wrench, remove the bolt holding the light mount onto the handlebar clamp.
- There is a small set screw that can be removed if the three locations shown are not usable for your desired adjustment.
- Mount the S1 to the light mount using the supplied hardware and 7/16” wrench and socket. The light can mount to either side of the light mount depending on how much pan adjustment is needed. Mount the light onto the handlebar and tighten it.
- Mount the light and route the power cord behind the number plate.
- Remove the seat and the gas tank (models vary). Unravel the provided S1 Pit bike Moto Kit wiring harness and locate the light plug lead.
- Connect the harness light plug (e) to the light power cord and route the handlebar switch (d) to a suitable location on the handlebars. Use Phillip’s head screwdriver to mount the switch. Route the battery leads (a,b) back to the battery along the frame along the existing OEM wiring harness.
- With the 8mm socket wrench (Applications vary), remove the red (+) battery terminal bolt and place the S1 Moto wiring harness red (+) ring terminal over and tighten the fastener. Then, remove the black (+) battery terminal bolt and place the S1 Moto wiring harness black (-) ring terminal over and tighten the fastener.
- Tie all wires away from sharp, hot, and/or rotating components. Replace the seat, tank, and any other parts removed to route the harness.
185 Bosstick Boulevard
San Marcos
CA ,92069
Phone 760-560-2252 x3
Fax 760-560-0383
info@bajadesigns.com
www.bajadesigns.com
References
- The Scientists of Lighting | Home - Baja Designs - Off-Road LED & Laser Lights | Automotive, Jeep, Truck, UTV, ADV, Dirtbike
- The Scientists of Lighting | Home - Baja Designs - Off-Road LED & Laser Lights | Automotive, Jeep, Truck, UTV, ADV, Dirtbike
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>