passau S28R 22 Inch Sound Bars for TV User Manual

passau S28R 22 Inch Sound Bars for TV

Please read this manual carefully before starting to operate the unit.
This prevents malfunctions and lets you experience all features of your new equipment.

Dear Customer,

Thanks your trust and congratulations on getting one of the best so unbar on the market!

Please refer to the notes below and follow the instructions to ensure that you use the so unbar correctly and have a good experience with this product.

If you got any question on using this soundbar or other issue, please send us a seller message in our Amazon store. You can also contact our support team: cici@miisso.com , We will provide a fast solution within 24 hours. Problems are often due to some steps missing or just changing one setting to solve.

Please don’t worry since it has 12-month warranty and lifetime service, feel free to tell us if you have any question.

SAFETY INSTRUCTIONS

• Read these instructions before using the product.
• Read all warnings carefully.
• Follow all instructions carefully.
• Do not use this apparatus near water.
• Clean only with dry cloth.
• Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions.
• Do not install the speaker system near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat.
• Protect the power card from being waled on or pinched particularly at plug points and the point where they exit from the unit.
• Only use attachments/accessories specified by the manufacturer.
• Use only with the cart, stand, tripod, bracket, or table specified by the manufacturer, or sold with the unit. When a cart is used, be cautious while moving the car-unit combination to avoid injury from tip-over.

EXPLANATION OF THE SYMBOLS ON THE DEVICE

WARNING: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER(OR BACK)NO USER-SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.

The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of uninsulated “dangerous voltage” within the product’s enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons.

The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance.

FCC Statement

NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which there receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help

Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. This device complies with Part15 of the FCC Rules. Operation is subject to the following two conditions:

1. this device may not cause harmful interference, and
2. this device must accept any interference received, including interference that may cause undesired operation.

PACKAGE CONTENTS

1. Soundbar: 1 unit
2. Audio Cable: 3 unit
3. User Manual: 1 unit
4. Remote Control: 1 unit
5. AAA Battery: 2 unit

UNIT OPERATION

1. Power-on: Insert the power cord that comes with the machine, the machine enters standby, and the LED display shows “—-“
2. BT mode: After the machine enters standby mode, short press the power button on the panel or the remote control power button to start the machine, and the machine enters the default BT mode , while the LED display shows ” bt “, then search the BT “S28R” to connect.
3. HDMl (ARC): Connect an HDMI (ARC) compatible device to the HDMl(ARC) port on the soundbar using an HDMI cable. Select HDRl(ARC) mode either by repeatedly pressing the standby button to select Input option: AUX/BT/ HDMI (ARC)/ USS button on your S28R or from the remote control by repeatedly pressing the Input key. Press the stands key on the sound bar’s control panel until “ARC” is displayed on the LED display. Ensure HDMI ARC is selected as audio output, then adjust the volume of the soundbar using the Volume up and Volume down buttons on the remote control or sound bar’s control
4. USB mode: Press the power button or the remote control INPUT button to enter USB mode, and the LED indicates red light and blue light at the same time, connect the corresponding audio source or insert a USB flash disk to play music, and the USB mode has priority function, that is, regardless of In what mode, when the USB flash disk is inserted, the USB flash disk will play first.
5. AUX mode: Press the power button or the remote control INPUT button to enter AUX mode, and the LED display shows “nou”, and then connect an external audio source to play music through the 3.5mm audio cable that comes with this machine. In AUX mode, the volume/treble and bass, and other functions are available to be adjusted.

SPECIFICATIONS

Driver Unit : 2.25″*2
S/N: .>=80dB
Distortion < 1 %
Power supply: DC13V/1.8A

DESCRIPTION OF THE REMOTE CONTROL

1. POWER: Turns on standby mode.
2. INPUT: Navigates between HDMI/AUX/BT/USB mode.
3. VOLUME{-,+}: Increase/decrease the volume.
4. : Skip to the previous track.
5. : Skip to the next track.
6. : Play/Pause the HDMI/BT/USB mode.
7. TRE {-,+}: Increase/decrease treble.
8. BASS{-,+}: Increase/decrease bass.
9. EQ : Choose audio output sound field effect.
10. : Mute the sound.
    

AC POWER

IMPORTANT NOTES

1. Make sure the power supply is proper and never handle the power cord or its plug with wet hands when plugging into, or unplugging from an outlet.
2. Ensure that the main power switch is in the “OFF” position before connecting the AC power cord to the power supply to avoid damage to the unit.
3. A damaged power cord can easily cause an electric shock or fire hazard; Never use a power cord after it has been damaged.

BATTERY INSTALLATION

1. Open the battery case.
2. Insert two batteries without the polarity reversed.
3. Close the battery case.
4. Keep within 5 meter range, 30 degree angle while aiming at the unit.

Precautionary note:

Remove the battery when the unit is not being used for a long period of time.

DESCRIPTION OF SOUND BAR PVC LENS

1. AUX IN
2. HDMI input
3. USB, Support USB flash disk, format: MP3/WMA
4. DC power input, power specification: 13V/1.8A

1. : Standby/Power On/INPUT selection key: Short press this key to power on/INPUT selection (INPUT selection sequence: BT–+HDMi–+USB–+AUX), long press to standby. a
2. : Play/Pause/Mute key: In BT/USB mode, press this key to play music, press again to pause playback. In AUX mode, press this key to mute, press again to cancel mute.
3. – : Volume down key: In USB/BT mode, short press this key to select the previous song, long press it to decrease the volume. In AUX mode, long press/short press this button will decrease the volume
4. +: Volume up key: In USB/BT mode, short press this button to select the next song, long press to increase the volume. In AUX mode, long press/short press this button will increase the volume.
   

How to Use

1. Power On: Use the Adaptor to connect the sound bar, plug the adaptor into a wall outlet, it will automatically enter into the standby mode and led indicator with white light will be shown on display
2. Short press the Power key on S28R the sound level automatically goes upto Level 15, press the standby button again to select Input option: AUX/BT/HDMl(ARC)/USB
3. Power off: To turn off, press and hold the Power key for 2 seconds or unplug from the wall mount.

Pairing

1. Make sure the S28R and your device are next to each other (within 1 meter /3 feet).
2. When using the S28R for the first time, turn on the unit, the Indicator will flash white light regularly. Select “BT” as input source. Now the speaker is in pairing mode.
3. Activate the Bluetooth function on your phone, tablet and search for nearby Bluetooth connections. Find II S28R II in the search results. Tap on the name to connect.

Using the Soundbar :Paring Modes

HDMi(ARC): Connect an HDMI (ARC) compatible device to the HDMl(ARC) port on the soundbar using an HDMI cable. Select HDRl(ARC) mode either by repeatedly pressing the standby button to select Input option: AUX/BT/ HDMI (ARC)/ USB button on your S28R or from the remote control by repeatedly pressing the Input key.

Press the stand by key on the sound bar’s control panel until “ARC” is displayed on the LED display. Ensure HDMI ARC is selected as audio output, then adjust the volume of the soundbar using the Volume up and Volume down buttons on the remote control or sound bar’s control.

AUX-in: Connect a compatible device using the 3.5mm jack cable. Select AUX mode either by repeatedly pressing the Input button on the remote control or repeatedly pressing the standby button on the soundbar control panel until nou is displayed on the LED display. Ensure the connected device is producing an audio signal, then adjust the volume of the soundbar using the Volume up and Volume down buttons on the remote control or soundbar control panel. buttons on the remote control or soundbar control panel.

Bluetooth: Repeatedly pressing the input button on the remote control or repeatedly pressing the standby button on the sound bar’s control panel until BT is displayed on the LED display. The LED display will flash to indicate that the soundbar is in Bluetooth pairing mode. Ensure that the device you wish to connect is also in pairing mode and search for S28R in its device list. When the two devices are paired, the LED display on the soundbar will stop flashing and turn solid. (The soundbar will now automatically re-pair with this device whenever it is within range and has Bluetooth turned on.)

USB Media Mode: The Soundbar is compatible with USB Flash Drive upto 64 gb & can play Mp3,WMV, WV audio files directly. Simply insert a compatible drive into the USB port on the rear end of the sound bar and the unit will If USB Mode is not. detected automatically please select the USB option by repeatedly pressing the Standby key on the soundbar and USB mode (also accessed via the remote control via input button).

Equalizer modes: The soundbar has 5 equalizer presets, tailored to complement various styles of music. Press the EQ button on the remote to choose between different sound effects.

IMPORTANT NOTES

• Make sure the power supply is correct and never handle the power cord or its plug with wet hands when plugging into, or unplugging from an outlet.
• Ensure that the main power switch is in the “OFF” position before connecting to AC power cord to the power supply to avoid damage to the unit.
• A damaged power cord can easily cause an electric shock or fire hazard, never use a power cord after it has been damaged.

Troubleshooting

Problem|
---|---
No Power| Make sure the S28R is plugged in and Turned “ON”
No sound|

1. Make sure you have selected Proper Source
2. Make sure the volume is set properly on the unit and the correct playback mode-(Bluetooth Android Device and AUX Input)
3. Check that soundbar system is not set to standby

Bluetooth pairing fail|

1. Check to see that both device are turned on and your Bluetooth Discoverable
2. Turn “OFF” & “ON” both the device
3. Make sure you have selected the Proper output Mode
4. Make sure you are within the 5 feet of unit
5. Move both the device away from other existing Bluetooth devices
6. Make sure unit is not paired to a previously paired device

No sound when receiving TV input|

1. Make sure that all connections are secure
2. Make sure the volume is set properly on the unit and at the television

No Remote control operation|

1. The battery might be dead, replace the battery

We’d Love to Hear From You!

We want to personally reach out and thank you for purchasing from our Amazon store.
Selling an Amazon is what we do to support our foamy, and product reviews are the lifeblood of our business.
Thank you again for being one of our amazing customers!

Customer Service

cici@miisso.com

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>