BLACK DECKER BDL310S Laser Level User Manual

: June 16, 2024
: Black Decker

Table of Contents

BLACK DECKER BDL310S Laser Level
Product Information
Product Usage Instructions
Safety Instructions
Installing the Battery
Assembly / Set-up
Troubleshooting
Out of Level Indicators
Maintenance
Service Information
Documents / Resources

BLACK DECKER BDL310S Laser Level

BLACK-DECKER-BDL310S-Laser-Level-PRODUCT

Product Information

The Laser Level Black & Decker Model BDL310S is a versatile tool designed for accurate leveling and alignment. It features a Class III laser that emits a visible laser beam for precise measurements.
The laser level can be used for various applications such as hanging pictures, installing shelves, aligning tiles, and more.
It offers both horizontal and vertical laser lines for increased flexibility. The device is powered by a battery, and it comes with a wall/tabletop mounting bracket for easy installation.

Specifications

Laser Class: Class I
Power Source: Battery
Operating Modes: Horizontal and Vertical
Mounting Options: Wall or Tabletop

Product Usage Instructions

Safety Instructions

Read and understand all instructions provided in the user manual before using the laser level.
- Failure to follow the instructions may result in electric shock, fire, or serious personal injury.
Avoid direct eye exposure to laser radiation as it can cause serious eye injury.
Use caution when working near electrical wiring or pipes.
- Always turn off the power before drilling, nailing, or cutting into walls, floors, or ceilings.

Installing the Battery

Ensure the laser level is turned off and disconnected from any power source.
Locate the battery compartment on the back of the device.
Open the battery compartment by sliding the cover in the direction indicated.
Insert the recommended battery into the compartment, following the polarity markings (+/-).
Close the battery compartment securely.

Assembly / Set-up

Attach the wall/tabletop mounting bracket to a vertical surface using either push pins or a screw hole, depending on the surface type.
If using push pins, ensure they are inserted into drywall only. For other surfaces, use the keyhole and a screw or nail in a predrilled hole.
Release the pins on the bracket by twisting the black knobs clockwise until they stop.
Position the bracket on the desired vertical surface and apply even pressure on both push pins or the keyhole to secure it firmly.

Laser Line Adjustment

To adjust the horizontal laser line, locate the right and left adjustment knobs at the rear of the moveable platform.
Turn the appropriate knob to elevate the horizontal laser line as needed.
To adjust the vertical laser line, locate the knobs at the front of the platform.
Turn the appropriate knob to rotate the vertical laser line to the right or left.
Always look at the target laser line and avoid staring directly into the laser beam.

Laser Operation

Slide the on/off switch to the (-) position to activate the horizontal laser beam for level measurements.
Slide the on/off switch to the (I) position to activate the vertical laser beam for plumb measurements.

FAQ

Q: Can I use this laser level on different surfaces?

A: Yes, you can use the laser level on various surfaces such as walls, floors, and ceilings. However, ensure proper mounting techniques are followed.

Q: Is the laser beam harmful to the eyes?

A: Yes, the laser beam can cause serious eye injury. Avoid direct eye exposure and always use caution when operating the laser level.

Q: How do I change the battery?

A: To change the battery, follow the instructions provided in the user manual.
Ensure the laser level is turned off and disconnected from any power source before replacing the battery.
WARNING: Read and understand all instructions.
Failure to follow all instructions listed below may result in electric shock, fire and/or serious personal injury.

SAVE THESE INSTRUCTIONS

Safety Instructions

DANGER: Laser Radiation, avoid direct eye exposure, serious eye injury can result.
Do not use optical tools such as a telescope or transit to view the laser beam.
Position the laser so unintentional eye contact will be avoided.
Do not operate the laser around children or allow children to operate the laser.
Do not disassemble. Modifying the product in any way can increase the risk of laser radiation.
WARNING: Use of controls or adjustments or performance of procedures other than those specified in this manual may result in hazardous laser radiation exposure.
Do not operate in explosive atmospheres, such as in the presence of flammable liquids, gases, or dust.
Use only with the specifically designated batteries. Use of any other batteries may create a risk of fire.
Store idle product out of reach of children and other untrained persons. Lasers are dangerous in the hands of untrained users.
Use only accessories that are recommended by the manufacturer for your model. Accessories that may be suitable for one laser, may create a risk of injury when used on another laser.
Repairs and servicing MUST be performed by a qualified repair facility.
Repairs performed by unqualified personnel could result in serious injury.
Do not remove or deface warning labels.
Removing labels increases the risk of exposure to radiation.
For indoor use only.
This product is intended for use in a temperature range of 41°F(5°C) – 104°F(40°C).
CAUTION: Use caution when drilling, nailing or cutting into walls, floors and ceilings which may contain electrical wiring or pipes.
Always turn off the power when working near electrical wires.
CAUTION: Use of controls or adjustments or performance of procedures other than those specified in this manual may result in hazardous laser radiation exposure.
The label on your tool may include the following symbols
V …………………………..volts
mW ……………………….milliwatts
nm…………………………wavelength in nanometers
IIIa…………………………Class IIIa Laser
For your convenience and safety, the following labels are on your laser.

Installing the Battery

Ensure laser on/off switch is in the left “OFF” position. Remove the battery compartment cover by pressing the tab of the cover in towards the center of the laser and out as shown in figure 4.
A rubber plug is located inside the compartment.
The plug is used to protect the laser from transportation damage.
Remove the plug by rotating it 90° and pulling it straight out.
Connect a fresh 9 volt alkaline battery making sure to match (+) and (-) terminals correctly. Replace the battery compartment cover.
Note: When transporting the laser or storing it for extended periods of time, remove the battery and replace the rubber plug.
WARNING: Choking hazard. Store rubber plug out of the reach of children.
WARNING: Batteries can explode, or leak, and can cause injury or fire. To reduce this risk:
Carefully follow all instructions and warnings on the battery label and package.
Always insert battery correctly with regard to polarity (+ and -), marked on the battery and the equipment.
Do not short battery terminals.
Do not charge batteries.
Remove dead battery immediately and dispose of per local codes.
Do not dispose of batteries in fire.
Keep batteries out of reach of children.
Remove battery if the device will not be used for several months.

Assembly / Set-up

Vertical Mounting

The wall / tabletop mounting bracket uses push pins or a screw hole to secure it to a vertical surface.
CAUTION: Pins are sharp and should be handled with care.
NOTE: The pins are only for use when hanging the bracket on drywall, NOT other surfaces including plaster. For surfaces other than drywall, the key hole can be used with a standard screw or nail in a predrilled hole.
The pins stay retracted until you are ready to mount the bracket. To release the pins, twist the black knobs shown in figure 5 clockwise until they stop.
Position the bracket on a vertical surface.
Hold the bracket as shown in figure 6, keeping your fingers on the front, and push in with even pressure on both knobs.
Make sure it is seated firmly and that the unit is secure on the wall.
IMPORTANT: When attaching or removing the bracket, be sure to push in or pull out with even pressure on both push pins.

Laser Line Adjustment

The horizontal or level laser line can be elevated as shown in figure 7 by turning either of the right or left adjustment knobs located at the rear of the moveable platform.
The vertical or plumb laser line can be rotated to the right or left by turning either of the knobs located at the front of the platform as shown in figure 8.
CAUTION: When making any laser line adjustments, be sure to look at the target laser line and not at the unit. Do not stare into the laser beam.

Hanging the Laser

The laser can also be hung from a joist or other secure structure by means of a hanging strap (not included).
CAUTION: Make sure laser is securely suspended by the strap.
To hang, thread the strap through the slot in the top of the laser and fasten the hook as shown in figure 9.
Adjust the laser so that it hangs relatively straight.
The selfleveling function will then compensate for any minor error +/- 5°.

Laser operation

Before attempting to use the laser, make sure the tool is positioned on a relatively smooth, flat and stable surface.
Brightness of area may effect line visibility.
When attaching to a mounting bracket or using the hanging strap, mount the laser securely.
Be aware that extreme temperature changes can cause movement or shifting of building structures, equipment, etc. which can effect accuracy.
Verify your set-up before each use as the laser may have moved.
This product is not recommended for outdoor use.

Turning the Laser On (Level Line)

Slide the on/off switch to the (-) position to operate the laser using a single horizontal laser beam as shown in figure 10.

(Plumb Line)

Slide the on/off switch to the (I) position to operate the laser using a single vertical laser beam as shown in figure 11.

(Crosshair Lines)

Slide the on/off switch to the (+) position to operate the laser using both the vertical and horizontal laser beams as shown in figure 12.

Troubleshooting

Problem	Possible Cause	Solution
• Laser does not project on wall or laser beam dim.	• Weak battery.	•

Replace with fresh battery.
• Laser lines are projected as a dashed lines.| • The self leveling range of the unit is +/-5 degrees. If the unit is not set within 5 degrees of vertical, one of the laser lines will project on wall as a dashed line.| • Be sure that the unit is as straight up and down as possible.
• Laser lines are projected but one line is solid and one line is dashed.| • The self leveling range of the unit is +/-5 degrees. If the unit is not set within 5 degrees of vertical, one of the laser lines will project on wall as a dashed line.| • Be sure that the unit is as straight up and down as possible.
• One laser line projected on wall is solid but not level.| • The self leveling range of the unit is +/-5 degrees. If the unit is not set within 5 degrees of vertical, one of the laser lines will project on wall as a dashed line. Dashed line is not turned on.| • Be sure that the unit is as straight up and down as possible.

• Turn the second laser line On to verify laser alignment.

Out of Level Indicators

The laser is equipped with “out of level indicators” which break solid laser lines into dashed lines when unit is tilted out of auto-leveling range +/- 5°. Always use both lines to verify straightness of laser.
Unit should be adjusted if any or both lines are broken or dashed. Figure 13 shows laser lines within auto-leveling range. Figures 14, 15 and 16 show laser lines out of auto-leveling range.

Storage

Always store the laser indoors with the switch in the “OFF” position. When storing it for extended periods of time, remove the battery and replace the rubber plug.

Maintenance

Use only mild soap and damp cloth to clean the tool.
Never let any liquid get inside the tool; never immerse any part of the tool into a liquid.
IMPORTANT: To assure product SAFETY and RELIABILITY, repairs, maintenance and adjustment (other than those listed in this manual)
should be performed by authorized service centers or other qualified service personnel, always using identical replacement parts.

Accessories

Recommended accessories for use with your tool are available from your local dealer or authorized service center.
If you need assistance regarding accessories, please call: 1-800-54-HOW-TO (544-6986).
WARNING: The use of any accessory not recommended for use with this tool could be hazardous.

Service Information

All Black & Decker Service Centers are staffed with trained personnel to provide customers with efficient and reliable power tool service.
Whether you need technical advice, repair, or genuine factory replacement parts, contact the Black & Decker location nearest you.
To find your local service location, refer to the yellow page directory under “Tools—Electric” or call: 1-800-544-6986 or visit www.blackanddecker.com