tp-link RE705X AX3000 Dual Band Mesh WiFi 6 Range Extender User Guide
- June 16, 2024
- tp-link
Table of Contents
- What should I do if I fail to configure TP-Link Range Extender?
- How to improve my wireless speed or range
- How to Connect Your Wireless Devices to the Range Extender via WPS as AP
- How to adjust Wi-Fi coverage of TP-Link Range Extender (new logo)
- References
- Read User Manual Online (PDF format)
- Download This Manual (PDF format)
What should I do if I fail to configure TP-Link Range Extender?
Troubleshooting
Updated 02-20-2023 07:40:04 AM 231571
This Article Applies to:
If you have already tried to configure the range extender but it failed,
please check the following troubleshooting.
Some tips before troubleshooting:
- If there is no RE light on some range extenders. It may have a Signal light or 2.4G/5G light. Please refer to the installation guide to check whether the extender is connected to the main network.
- End-device means a computer, laptop, front-device(s) means your modem or main router, etc. which the TP-Link router is connected.
- DFS Function: For Dual-Band Range Extender if there’s only a 2.4G LED light on, then 5G light off, please help fix the main router’s 5G to band1 (channel 36-48), then the RE should be able to connect to the Router in 5G.
- Router Advanced Features: Check those main router functions that may have a bad influence on RE to connect and work stably:
Fix Unstable Connection on the Range Extender by Changing Router Advanced Features | TP-Link
Case 1: The RE light is off after the configuration
-
Check if the user enters the correct Wi-Fi password on the extender.
a. By forgetting Wi-Fi and reconnecting to the home Wi-Fi, enter the password again.
b. on iPhone, go to WLAN-> highlight the connected network name, and enter iPhone’s password to see the password. -
Put the range extender 2-3 meters away from the router. Factory reset it by pushing the reset button for a few seconds. And configure the range extender from scratch.
-
If possible, suggest giving a different name for 2.4G and 5G Wi-Fi on the Main router. It will help us to locate which band has a connection issue with the router.
-
If the RE light is finally on but still has no internet access, please go through and refer to Case Two or Three. If the RE light is still off, turn off and on the range extender and wait two to 2 minutes then check if the RE light will be lit.
-
Upgrade the range extender to the latest firmware and reconfigure it. Click here.
-
Make sure the main router doesn’t enable any security settings, like MAC Filtering or Access control. And Authentication Type and Encryption type are Auto on the router.
-
Try resetting the extender completely. Use a pin to press the button for 1 second to reset the extender. Also, once you reset, you need to reconfigure the extender following the FAQ: How to configure Range Extender via Tether APP
8. Log into the range extender by using www.tplinkrepeater.net or the IP address assigned
by the router (find the IP address from the router’s interface). Take picture of the Status page and
save the system log (Save the log within 3-5 minutes after the range extender reboot).
Case 2: The RE light is on, and the end devices can not connect to the Wi- Fi of the range extender.
-
Check the wireless signal strength of the end devices. If only one end device cannot join the WiFi of the range extender,remove the profile of the wireless network and connect it once again.
And connect it to your router directly to see if it can connect. -
If multiple devices cannot connect to the extender SSID, you may also follow the below link to see if can configure it well:
What’s the solution if my TP-Link range extender can’t connect to my router
properly?
Case 3: The RE light is on, and the end devices can connect to the Wi-Fi of
the range extender but have no network access.
- Do not set the same SSID for the range extender and router. Otherwise, please reset the range extender and create a separate SSID.
- Upgrade the range extender to the latest firmware and reconfigure it. Click How to upgrade the firmware of my range extender.
- Try multiple end devices. If only one end device doesn’t have internet access, check whether the end device is obtaining an IP Address automatically. What if it connects to the main router directly?
- Connect the same end device to the main router directly to check its internet connectivity. Check its IP address and Default Gateway when connected to the router and range extender. (click here)
- Make sure the main router doesn’t enable any security settings, like MAC Filtering or Access control.
- Log into the range extender by using www.tplinkrepeater.net or the IP address assigned by the router (find the IP address from the router’s interface). Take picture of the Status page and save the system log (Log taken within 3-5 minutes after the range extender reboot).
- In this case, we may also follow the below link to see if we can configure it well:
What’s the solution if my TP-Link range extender can’t connect to my router
properly?
Note:
If the error message “No Host Network Connection” pops up after “the apply
settings”, it’s probably because the router’s 5G is using the DFS channel,
please try to disable Band Steering on the router and change the 5G channel to
Band 1(36, 40, 44, 48).
If all the troubleshooting can not fix the issue, you try the suggestions on
the forum:
Recommended settings on the host router to work well with TP-Link Range
Extenders Please contact TP-Link support if the steps above do not solve the
problem. Let us know the model number of your Router and which band you
expand, 2.4GHz or 5GHz.
TP-Link Range Extender Stops
Working
Troubleshooting
Updated 02-16-2023 10:12:15 AM 3318
This Article Applies to:
If your TP-Link range extender was working fine before, but it failed to
connect to the host router suddenly, the following troubleshooting may help
you figure it out.
Case1. The extender stops working with nothing changed on the host router
- Try rebooting your router and the extender.
- Ensure that your extender is within range of the router.
- Ensure that the range extender is not affected by interfering devices such as metal objects, fish tanks, microwaves, Bluetooth devices, and so on.
- If the above steps didn’t resolve the issue, try resetting the extender completely. Use a pin to press the button for 1 second to reset the extender. After resetting, you will need to reconfigure the extender following the FAQ:
How to configure Range Extender via Tether APP
Case 2. The extender stops working after changing the host router
If the host router was changed, you need to reset the extender and reconfigure
it again.
Use a pin to press the button for 1 second to reset the extender. Also, once
you reset, you need to reconfigure the extender following the FAQ:
How to configure Range Extender via Tether APP
Case 3. The extender stops working after changing some settings on the host
router
If you recently changed the settings on your host router, such as Access
Control settings, channel, etc. You may try to check and modify the settings
on the host router by following the instruction:
Recommended settings on the host router to work well with TP-Link Range
Extenders
If the troubleshooting steps are still not working, try upgrading the firmware
to the latest version, you can refer to the FAQ for instructions on how to do
this:
How to upgrade the firmware of my range extender (new logo)
If the firmware update still cannot fix the issue, please contact support and
provide us with the following info for further troubleshooting:
- The LED status of the extender, you can take a photo.
- The IP address when the device (phone or laptop) is connected to the extender.
- The IP address when the device (phone or laptop) is connected to the router.
- The model number of your main router.
- Firmware of the extender.
How to improve my wireless speed or range
User Application Requirement
Updated 06-29-2022 01:53:37 AM 1390858
This Article Applies to:
Overview:
To improve the wireless speed or range, it is highly recommended to work on
the following common solutions:
- Choosing the best location
- Optimizing configuration of the device
- Upgrade the equipment
Symptom:
Weak wireless signal showed, low wireless speed or range. Cause:
The factors most frequently affecting the wireless signal:
Intrinsic factors:
Transmission Distance.
Regarding on the wireless device particularly working on 5GHz band, it will be
more sensitive to the obstacle. Though there will be more clear channels than
those of 2.4GHz bands, the wireless signal will be reduced significantly and
transmit in shorter range due to higher frequency.
Antenna.
Omni-directional antennas and directional antennas
Omni-directional antennas are resembled in our home products like wireless
router or wireless ADSL2+ Modem Routers, they radiate horizontally all around,
but are weaker upward or downward as the picture shows.
While a directional antennas radiate strongly in a particular direction which
are usually used for high power outdoor products. The gain of a directional
antenna increases, also with the coverage distance, but the effective coverage
angle decreases. Generally, the higher gain value of an antenna, the better
directional ability will be.
For directional antennas, the lobes are pushed in a certain direction and little energy is there on the back side of the antenna. Please refer the picture below.
This phenomenon will be more significant once you deploy the High-Gain antenna, so we recommend that to confirm precise on horizon direction otherwise there be unexpected dramatic signal loss.
Wireless Communication Performance.
Higher transmission rates, better performance
Extrinsic factors:
– Physical Barriers, such as wall or clapboard and so on;
– Other similar devices and other sources such as microwave ovens, cordless
phones or other technologies that use the same band as Bluetooth
– There are more than one AP or wireless routers working in the same Channel.
– The location where an AP or wireless router is placed. You’d better to place
the device at a higher location to reduce the barrier’s countercheck.
Solution:
-
Choosing the best location
-
Antennas should be positioned for best location and direction
– Deploy the antenna in good location and correct angle, and also make sure your wireless client devices are in the coverage;
– For multi-story buildings wireless coverage, we recommend to placing antennas at 45 degrees (diagonally) or 0 degrees (straight out parallel to the floor) which will be more effective. Since antennas always transmit weakly at the base, do not place your wireless client device at the bottom of TP-Link wireless router or access point. -
Try best to avoid the extrinsic interference
– Avoiding the physical interference in the wireless coverage, each wall or ceiling will have a negative effect on wireless radio particularly the ones built by solid metal material ;
– Keep your device away from various electromagnetic noise sources that generate RF noise, like microwaves, Monitors, electric motors, copying and fax machines, etc.
Optimize configuration of the device
– For TP-Link wireless products, we recommend to do corresponding settings to avoid the interference from other networking and radio frequency equipment.
First, please log into the product and you can refer to this link as guidance. Here we take TL-WR1043ND user interface as an example and then please go to Wireless->Wireless settings and change the channel settings, the default value is Auto and here we recommend select 1, 6 or 11 if you suffer high wireless interference.
For 802.11b&g, there are 14 channels designated in the 2.4 GHz range and three
nonoverlapping channels recommended: 1, 6 and 11 (1, 7 and 13 in part European
region, please obey your local regulations or laws). Sometimes the “well-
known” channels will be also crowded and we recommend to select the
appropriate one adjusted to your local environment.
Upgrade the equipment
– If you want to have a big improvement immediately and boost the wireless
throughput, you can also choose to upgrade a combination of antennas or other
wireless equipment to enhance the wireless transmission; – If you are in a
congestion wireless environment, the wired connection can be taken into
consideration and the TP-Link Powerline equipments is a good alternative.
How to Connect Your Wireless Devices to the Range Extender via WPS as AP
mode (Blue UI)
Configuration Guide
Updated 06-28-2022 02:42:42 AM 62979
This Article Applies to:
Wi-Fi Protected Setup (WPS) provides an easier approach to set up a security-
protected Wi-Fi connection.
Wireless devices that support WPS, including Android phones, tablets, most USB
network cards, can be connected to your extender through this method (not
supported by iOS devices).
-
Visit http://tplinkrepeater.net, and log in with the username and password you set for the extender.
-
Go to Settings > Wireless > WPS.
-
Enable WPS.
-
Connect via WPS:
• AP’s PIN: Enable AP’s PIN and enter the PIN on your device. You can click Generate to get a new PIN or click Default to restore the PIN to its factory one.
• Push Button (Recommended): Click Connect and push the WPS button on the client device.
• PIN code: Enter the client’s PIN, and click Connect.
Get to know more details of each function and configuration please go to Download Center to download the manual of your product.
How to adjust Wi-Fi coverage of TP-Link Range Extender (new logo)
Q&A of functional explanation or specification parameters
Updated 06-28-2022 02:25:22 AM 85511
This Article Applies to:
You can set the extender’s Wi-Fi coverage depending on how large you want your
Wi-Fi area to be.
Here takes TL-WA820RE as demonstration:
-
Log into the Web GUI of the range extender. If you don’t know how to do that, please refer to How to log into the Web GUI of my 11N Range Extender (new logo)?
-
Go to Settings > Advanced Settings > Wi-Fi Coverage.
-
Select Min, Mid or Max to adjust your Wi-Fi coverage of the extender.
-
Click Save.
Get to know more details of each function and configuration please go to Download
Center to download the manual of your product.
How to Boost Your Wi-Fi Signal
Before You Buy
Updated 11-23-2021 06:28:35 AM 383234
This Article Applies to:
What if the Wi-Fi signal coverage is not good because of the Wi-Fi dead zone?
Below is the comparison of Range Extenders, Powerline Adapters, and Mesh
devices, etc, you may choose an appropriate solution based on your own
requirements.
Range Extender (RE)
Wi-Fi Range Extenders boost the existing Wi-Fi in your home by receiving the
wireless signals from your router and repeating them with powerful amplifiers
and antennas, extending your coverage by up to twice the range. Just place the
range extender about halfway between your router and the Wi-Fi dead zone. The
extender will capture and repeat the Wi-Fi signal from your router to the
surrounding areas to expand your wireless network coverage. Your devices can
connect to the network either through your router or extender as you move
around your house.
So sudden signal drops or Wi-Fi dead zones become a thing of the past.
Note: Like wireless routers, range extenders also suffer from interference
from obstacles such as concrete walls, metal objects, and microwaves. To avoid
such obstacles for the best wireless performance. All TP-Link range extenders
have a Signal LED to indicate the signal strength a range extender gets from
the main router, which can help you find the best location for your extender.
Power line Adapter (PLC)
Powerline networking solutions transmit data and extend your home network
using existing electrical wiring. Eliminating the need for expensive and
complicated Ethernet cables. Thick walls
and similar obstacles aren’t an issue the way they might be with a range
extender.
Note: Both powerline adapters will need to be on the same electrical circuit.
If your home is wired on multiple circuits, you’ll need to check that the
section of your home with the router and the section you want to add coverage
to are on the same circuit.
Mesh
If you still encounter Wi-Fi dead-zones when walking around your home, you can
take TP-Link’s whole-home mesh Wi-Fi solutions into consideration. Mesh Wi-Fi
network, multiple network nodes work together to form a single, unified
network that shares the same Wi-Fi settings. To know more about it, refer to
https://community.tp-link.com/en/home/stories/detail/407
TP-Link currently provides two mesh Wi-Fi solutions:
- Deco: Whole new mesh ecosystem
Setting up a whole new Wi-Fi system is a good choice if you want to have a new
and highquality system.
For more details, please refer to https://www.tp-link.com/support/faq/1427/
When Deco works with the existing router, here are two typical connection
structures. Topology 1:
Topology 2—-Ethernet backhaul, please refer to https://www.tplink.com/support/faq/1794/
- One MeshTM: Cost-effective mesh network with existing TP-Link devices
One Mesh network can provide stability, good performance network for you. If you already have a One Mesh router like Archer A7, you can just add a repeater to build a Whole-Home WiFi System.
To know more about an OneMeshTM network, refer here.
Referring to the following summary and your house situation to choose the best Wi-Fi dead zone killer.
Scheme
Comparison| Range Extender| Power Line
Adapter| Mesh| Deco P7&Deco P9
---|---|---|---|---
One- Story Home| 0| 0| 0| 0
Multi-Story
Home| 0| 0| 0| 0
How to extend| Wireless| Power Line| Wired or
Wireless| Wired, Wireless, or
Powerline
Implementation
Conditions| No| Under the same
power circuit| No| Under the same
power circuit for
| | | | Powerline
transmission
Configuration
Convenience| App Easy
deployment| Plug and Play| App Easy
deployment| App Easy
deployment
Reliability| Fair| Good| Great| Excellent
Product
Highlights| AC Passthrough| AC Passthrough ( the model with le
letter”P”)| Ethernet
Backhaul| Ethernet and
Powerline
Backhaul
Scheme Details| Click here >>| Click here >>| Click here >>| Click here >>
◊: Recommendation Index
Disclaimer: Maximum wireless transmission rates are the physical rates derived
from IEEE Standard 802.11 specifications. Range and coverage specifications
along with the number of connected devices were defined according to test
results under normal usage conditions. Actual wireless transmission rate,
wireless coverage, and a number of connected devices are not guaranteed and
will vary as a result of 1) environmental factors, including building
materials, physical objects, and obstacles, 2) network conditions, including
local interference, volume, and density of traffic, product location, network
complexity, and network overhead and 3) client limitations, including rated
performance, location, connection quality, and client condition.
References
- Trying to Configure the Range Extender? | TP-Link
- Trying to Configure the Range Extender? | TP-Link
- Mesh Wi-Fi Network for Unified Whole-Home Coverage - Home Network Community
- Recommended settings on the host router to work well with TP-Link Range Extenders - Home Network Community
- Download Center | TP-Link
- Download Center | TP-Link
- How to log into the Web GUI of my brand new 11N Range Extender (new logo)? | TP-Link
- How to upgrade the firmware of my range extender (new logo) | TP-Link
- How to find IP address on your devices | TP-Link
- What's the solution if my TP-Link range extender can't connect to my router properly?
- Fix Unstable Connection on the Range Extender by Changing Router Advanced Features | TP-Link
- How to improve my wireless speed or range | TP-Link
- How to improve my wireless speed or range | TP-Link
- How to improve my wireless speed or range | TP-Link
- Award-Winning Best Mesh WiFi Systems By TP-Link
- Powerline | TP-Link
- Range Extenders | TP-Link
- OneMesh | TP-Link United Kingdom
- TP-Link - Contact Technical Support
- Contact Technical Support | TP-Link United Kingdom
- How to configure Range Extender via Tether APP | TP-Link
- How to upgrade the firmware of my range extender (new logo) | TP-Link
- What’s a Deco Whole-Home Wi-Fi System and How it works? | TP-Link United Kingdom
- General questions about Ethernet Backhaul feature on your Deco | TP-Link