Joy Pebble YH-2211 Electric Fireplace Heater Instruction Manual
- June 16, 2024
- Joy Pebble
Table of Contents
Joy Pebble YH-2211 Electric Fireplace Heater
NO VENTING REQUIRED
WARNING
Read and understand this manual thoroughly before plugging in or using the
appliance. Failure to comply with these precautions could result in fire,
electric shock, or serious personal injuries.
Specification
Parts List
- 1 Electric heater
- 1 User manual
- 4 Legs
- 12 Screws
Important Instructions
PLEASE READ ALL INSTRUCTIONS BEFORE USING THIS HEATER. WHEN USING ELECTRICAL APPLIANCES, BASIC PRECAUTIONS SHOULD ALWAYS BE FOLLOWED TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK AND PERSONAL INJURY, INCLUDING THE FOLLOWING: When switching on the appliance for the first time, allow it to run at full power for about two hours to get rid of the unpleasant smell. Make sure that the room in which the appliance is located is well ventilated during this operation. It is normal for the appliance to emit small cracking sounds when you turn it on for the first time. Security Advice
- Read all instructions before using this heater.
- This heater is hot when in use. To avoid burns, do not let bare skin touch hot surfaces. Use a handle when moving the unit. Keep flammable materials such as furniture, pillows, bedding, papers, clothes, and curtains at least 3 feet (0.9 m) from the front and top of the heater and keep them away from the sides and the rear of the heater. Keep the rear grille away from walls or drapes so as not to block the air intake.
- Extreme caution and supervision are necessary when any heater is used near children or invalids and whenever the heater is left operating and unattended.
- Always unplug the heater when not in use.
- Do not use any heater when it has a damaged cord or plug, it malfunctions, or has been dropped or damaged in any manner. Discard the heater or return it to an authorized service facility for examination and/or repair.
- Do not use it outdoors.
- This heater is not intended for use in bathrooms, laundry areas or other similar indoor locations. Never locate the heater where it may fall into a bathtub or other water containers.
- Do not run the cord under carpeting. Do not cover the cord with throw rugs, runners, or similar coverings. Do not lay out the cord under furniture or appliances. Arrange the cord away from traffic areas and place it where it will not be tripped over.
- To disconnect the heater, turn off the control, and then remove the plug from the outlet.
- This appliance has a polarized plug (one blade is wider than the other). This plug is intended to fit a polarized outlet only one way. If the plug does not fit fully in the outlet, reverse the plug. If it still does not fit, consult a qualified electrician. Do not connect the heater to extension cords, surge protectors, timers, direct breakers, or an outlet with other appliances connected to the same outlet. Risk of fire, overheating, malfunction, property damage, injury, or even death may result if not adhered to!
- Only connect to properly polarized outlets.
- Do not insert or allow foreign objects to enter ventilation or exhaust openings, as this may cause an electric shock or fire, or damage the heater.
- To prevent a possible fire, do not block air intakes or exhaust in any manner. Do not use on soft surfaces, like a bed, where openings may become blocked.
- A heater has hot and arcing or sparking parts inside. Do not use it in areas where gasoline, paint, or flammable liquids are used or stored.
- Use this heater only as described in this manual. Any other use not recommended by the manufacturer may cause fire, electric shock, injury to persons or other damage to property.
- This heater must be plugged into a 120V, 15 amp (or more) circuit of its own. Nothing else can be plugged into the same circuit. If you are unsure whether the circuit in your home meets this specification, consult a certified electrician prior to use. Risk of fire, overheat, malfunction, property damage, injury, or even death may result if not adhered to!
- To prevent overload and blown fuses, be sure that no other appliance is plugged into the same outlet or into another outlet wired into the same circuit.
- It is normal for the heater’s plug and cord to feel warm to the touch. A plug or cord that becomes hot to the touch or becomes distorted in shape may be a result of a worn electrical outlet. Worn outlets or receptacles should be replaced prior to the further use of the heater. Plugging the heater into a worn outlet/receptacle may result in overheating of the power cord or fire.
- Ensure the heater is on a stable, secure surface to eliminate the potential of tipping over.
- Always plug the heater directly into a wall outlet/receptacle. Never use with an extension cord or relocatable the power tap (outlet /power strip).
- Be sure that the plug is fully inserted into an appropriate receptacle. Please remember that receptacles also deteriorate due to aging and continuous use: check periodically for signs of overheating or deformations evidenced by the plug. Do not use the receptacle and CALL your electrician.
- Check that neither the appliance nor the power cable has been damaged in any way during transportation.
- Make sure that no pieces of polystyrene or other packaging material have been left between elements of the appliance. It may be necessary to pass over the appliance with a vacuum cleaner.
- This appliance is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction concerning use of the appliance by a person responsible for their safety. Children should be supervised to ensure that they do not play with the appliance.
CAUTION: To prevent electric shock, match and fully insert the wide blade of the plug to the wide slot.
SAVE THESE INSTRUCTIONS
User Guide
Location of Controls
- Thermostat control knob (TEMPERATURE SETTING) – Adjust to maintain the room temperature
- Flame switch – Switch the flame effect and turn the power on/off
- Heating setting – Please press for 1000W
- Heating setting – Please press and at the same time for 1500W (it can not operate without pressing first)
- Flame dimmer control – Adjust the flame intensity
Attaching The Legs
- Turn the product on its side to start attaching the legs.
- Place a leg on each corner and use 3 screws to fix each leg.
- Tighten the screws clockwise until each leg is tightened.
- Turn the unit back up to standing position and make sure it is stable.
- Place the unit on the required location and plug in. It is now ready for use.
NOTE: The drawing below is for illustration purposes only. Your product may be slightly different in appearance but the operations are the same.
Overheating Safe Device
If the heater stops working, turn off the heater and inspect the blockage of the inlet or outlet. Disconnect the plug and wait at least 10 minutes for the protection system to reset before attempting to restart the heater. If the safe device still switches off the heater and makes the heater fail to operate, contact us via Amazon Message, or call customer service numbers: 213-4467172 and/or 661-4358826.
Attention: Before restarting the heater, the plug must be disconnected for at least 10 minutes
Cleaning
- Always disconnect the appliance from the main supply before cleaning.
- Clean the outside of the heater by wiping it with a damp or dry cloth.
- Do not use petroleum, any other detergent or chemical solvent to clean the heater.
- When the heater is not used for a long time, it should be protected from dust and stored in a clean and dry place.
Disposal
Environmental Protection
Waste electrical production should not be disposed of with household waste.
Please recycle where facilities exist. Check with your Local Authority or
retailer for recycling advice. Thank you for purchasing this product! If you
have any questions about the product, such as missing parts, damaged products,
product assembling, and operation, please contact us via Amazon Message or
customer service number: 213-4467172 or 661-4358826.661-4358826.
IMPORTANT
Please call our customer service department for any consulting: 213-4467172
661-4358826 (8:30 am – 5:30 pm P.S.T.) DATED PROOF OF PURCHASE IS REQUIRED FOR
WARRANTY SERVICE.
Address: ROWAN ELECTRIC APPLIANCE LLC 28407 Ascent Way, Santa Clarita, CA 91350 Phone: 213-4467172 or 661-4358826