ACEFAST K1 Party Karaoke All In One Audio Set User Guide
- June 16, 2024
- ACEFAST
Table of Contents
ACEFAST K1 Party Karaoke All In One Audio Set
Product information
- Light control/on-off key (BT indicator light, ring 9light, membrane light)
- Microphone key (Microphone indicator light)
- AC cancellation key/recording playback cancellation (Sound source indicator light)
- Pause/play/answer/hang up calls/smart voice
- Volume-/previous track
- Volume+/next track
- Mode switch key/TWS pairing key (TWS indicator light)
- EQ key (Reverb mode indicator light)
- Decrease reverb key
- Increase reverb key
- Microphone volume
- Microphone volume+
- Battery indicator light (100% – 4 lights on, 75% – 3 lights on, 50% – 3 lights on, 25% – 1 light on)
- MIC
- TYPE-C charging and live OTG
- TF card slot
- AUX audio interface
- Monitoring/analog live broadcast
- USB port (supports reverse charging)
- 6.5 audio plug (supports various musical instruments)
Operating instructions
- Press and hold the power button to turn on. After powering on, the BT status indicator light will flash.
- Open the BT settings on your phone and search for “ACEFAST K1”. Tap to connect, and once connected, you will hear a prompt sound and the green light will stay on.
- Press and hold the microphone power button to turn on the microphone. Press the microphone button on the speaker to activate the Karaoke mode.
- Memory function: When the speaker is powered off and then powered on again, it will remember the previous settings such as speaker volume, microphone volume, reverb level, and other settings.
| Long press to power on/off In case of system freeze, long press for 8
seconds to power off and restore factory settings Short press to switch
between different lighting modes (such as Pulse, Marquee, Spectrum, or Turn
off the lights)
---|---
| Short press to activate K-song mode
| Single click to eliminate the original sound, press again to resume normal
playback / Long press for 2 seconds to cancel internal recording and external
playback
| In BT/TF card playback mode, short press to pause playback. In AUX playback
mode, short press to play/pause Short press to answer/end a call Double press
to reject a call/redial the last dialed number Long press for 3 seconds to
activate the voice assistant
| Short press for volume-/volume+ Long press for 2 seconds to play the
previous/next track
| Short press to switch between BT/TF/USB/AUX playback modes Long press for 2
seconds until you hear a beep, then release to disconnect the BT connection
Long press for 8 seconds to restore factory settings Double click to enter TWS
mode/cancel pairing
| Short press to switch EQ modes (Normal, 3D, and Bass Boost)
Long press for 8 seconds to enable power-saving mode
| Short press for reverb-/reverb+
| Short press for microphone volume-/microphone volume+
Specifications and their parameters
| BT version: | Actions 5.0+MVSILICON DSP |
|---|---|
| DSP sound: | Bass boost |
| Output power: | 200W Max |
| Voltage time: | DC 5V/3A |
| Charging time: | 4 – Sh |
| TWS connection range: | < 6m |
| BT range: | > 10m(open area) |
| AUX mode: | 3.5mm audio jack |
| TF card mode: | Max 128G TF card |
| USB mode: | Max 128G USB |
| Speaker size: | 78mm*2+57mm-k2 |
| Battery capacity: | 18000mAh |
| Product size: | 396131174mm |
| Product weight: | 3.274KG |
| Charging method: | Type C 5V/3A |
| Impedance: | 40Ω ±15% |
Wireless Charging Microphone Instructions:
- During use, the handheld K1 wireless charging microphone’s display shows a 3-bar battery indicator when the battery is sufficient. When the battery symbol is empty, it indicates low battery, please charge it promptly.
- When charging, please use the included USB charging cable to charge the microphone. The red light will illuminate during charging and turn off when fully charged.
- For the first time use, it is recommended to completely drain the microphone’s battery before charging.
- If purchasing two microphones, make sure their frequency channels are set apart to avoid interference.
- In TWS (True Wireless Stereo) mode, only two microphones with different frequency channels can be connected.
Note : When using the microphone, hold it by the middle part. Holding it by the bottom can block the antenna and cause signal interruption or intermittent connection.
Warning:
Under extreme circumstances, misuse or mishandling of standard/charging
batteries can lead to leakage and potential hazards, such as overheating,
fire, explosion, or the release of smoke or harmful gases.
Dispose of discarded products, including batteries, at authorized recycling
centers or through professional dealers.
Use only the chargers recommended by the manufacturer (5V/3A 9V/2A).
Only charge the batteries in an environment with a temperature below 40°C.
Turn off the battery-powered device after use.
Even if not in use for a long period, it is recommended to periodically
charge the batteries (approximately every 3 months).
Do not exceed 70°C when heating the charging batteries. Avoid exposure to
sunlight and do not throw the batteries into fire.
Warranty & Customer Support
For questions, support, or warranty claims, contact us at the mail below that corresponds with your region. Please include your Amazon order number and product model number.
Amazon US orders : support1@acefast.com
Amazon EU orders : support2@acefast.com
Amazon UK orders : support3@acefast.com
Amazon CA orders : support4@acefast.com
Amazon JP orders : support5@acefast.com
Other region orders : support6@acefast.com
Please note, ACEFAST can provide after sales service for products purchased from any official ACEFAST store. If you have purchased from local seller, you can also contact them directly for service or warranty issues.
Shenzhen Houshuxia Technology Co., LTD www.acefast.com | support@acefast.com Rm203, 2nd Floor, Building C, Youth Pioneer Park, Jianshe East Road, Tsinghua Community, Longhua Street, Longhua District, Shenzhen, P. R. China Shenzhen, 518000, China
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>