GJJKTD Starfish Smart Wifi Led Retrofit User Manual
- June 16, 2024
- STARFISH
Table of Contents
STARFISH SMART WIFI
LED RETROFIT DOWNLIGHTS
LJC-US-SDLG3F-Y4C10.5W950-RGBCW12W-21V1；LJC-US-SDLG3F-Y6C13W950-RGBCW12W-
21V1
LJC-US-SDLG3F-F4C10.5W950-RGBCW13W-21V1 ；LJC-US-SDLG3F-F6C13W950-RGBCW13W-
21V1
INSTALLATION AND SAFETY INSTRUCTIONS
IMPORTANT: Read before installing fixture. Retain for future reference.
WARNING: Risk of Fire or Electric Shock
- LED Retrofit Kit installation requires knowledge of luminaries electrical systems. If not qualified, do not attempt installation. Contact a qualified electrician.
- To reduce risk of fire and over-heating, secure all connections.
- TURN OFF the electrical power before proceeding.
- Install this kit only in luminaires that have the construction features and dimensions shown in the photographs and/or drawings and where the input rating of the retrofit kit does not exceed the input rating of the luminaire.
- The electrical rating of this product is 120V/60Hz.
- To prevent wiring damage or abrasion, do not expose wiring to edges of sheet metal or other sharp objects.
- Do not make or alter any open holes in an enclosure of wiring or electrical components during kit installation.
- This retrofit kit is accepted as a component of a luminaire where the suitability of the combination shall be determined by authorities having jurisdiction.
- This device is not intended for use with emergency exits.
- Suitable for wet locations, covered ceiling-mounted luminaire.
INSTALLATION
STEP 1: Turn OFF power prior to installation.
STEP 2: Remove existing trim installed in recessed housing (if necessary).
STEP 3: If applicable, slide lamp holder bracket to its upward maximum
position. If the lamp holder bracket is less than 4 1/2″ from the bottom edge
of the fixture enclosure, the lamp holder bracket must be removed.
STEP 4: If necessary, remove the lamp holder mounting bracket and the lamp
holder from the bracket, then attach the provided label to the existing
luminaire. See Figure A.
STEP 5: Install adapter into socket. See Figure B.
STEP 6: Connect the orange terminals together. See Figure C.
STEP 7: To install the 4″ downlight, slide the downlight up into the recessed
housing. Push the trim until the outer edge is flush with the ceiling surface.
See Figures D & F.
STEP 8: To install the 5″/6″ downlight, insert torsion springs into luminaire
housing brackets. Gently push up trim and slide the LED downlight up into the
recessed housing until the trim is flush with the ceiling. See Figures E & F.
STEP 9: Installation is complete. Turn power ON.
STEP 10: App Connection: To connect your device, download the free “Starfish
Smart Lighting” App from the app store. Please refer to our Starfish User
Guide for detailed instructions on how to pair your device.
For Installation into existing recessed LED luminaire with compatible connectors:
-
Follow STEPS 1 and 2 above.
STEP 3: Discard medium base adapter. -
Skip STEPS 4 and 5 above. Continue with STEPS 6 – 9 above.
https://smartapp.tuya.com/satcosmart
FCC Statement
This equipment has been tested and found to comply with the limits for a Class
B digital device, pursuant to part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and
on, the user is encouraged to try to correct the interference by one or more
of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
This device complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance of 20 cm between the radiator and your body. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
- this device may not cause harmful interference, and
- this device must accept any interference received, including interference that may cause undesired operation.
Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>