ENGLAON LED22M60 22 Inch TV Full HD Smart 12V TV User Manual

**ENGLAON LED22M60 22 Inch TV Full HD Smart 12V TV User Manual

**

Safety Information

IMPORTANT SAFETY INSTRUCTIONS

Read these instructions.
Keep these instructions.
Heed all warnings.
Follow all instructions.
Do not use this apparatus near water. Clean only with dry cloth.
Do not block any ventilation openings. Install in accordance with the manufacture’s instructions.
Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat.
Do not defeat the safety purpose of the polarized or grounding plug. A polarized plug has two blades with one wider than the other. A grounding plug has two blades and a third grounding prong. The wide blade or the third prong is provided for your safety.
If the provided plug does not fit into your outlet, consult an electrician for replacement of the obsolete outlet.
Protect the power cord from being walked on or pinched particularly at the plugs, convenience receptacles, and at the point where they exit from the apparatus. Only use attachments/accessories specified by the manufacturer.
Use only with the cart, stand, tripod, bracket, or table specified by the manufacturer, or sold with the apparatus. When a cart or rack is used, use caution when moving the cart/apparatus combination to avoid injury from tip- over.

Unplug the apparatus during lightning storms or when unused for long periods of time.
Refer all servicing to qualified personnel. Servicing is required when the apparatus has been damaged in any way, such as power supply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped.
CAUTION: These servicing instructions are for use by qualified service personnel only. To reduce the risk of electric shock, do not perform any servicing other than that contained in the operating instructions unless you are qualified to do so.
WARNING: To reduce the risk of fire or electric shock, do not expose this apparatus to rain or moisture. The apparatus shall not be exposed to dripping or splashing and that objects filled with liquids, such as vases, shall not be placed on apparatus.
WARNING: The mains plug is used as disconnect device, the disconnect device shall remain readily operable.

CAUTION
RISK OF ELECTRIC SHOCK DO NOT OPEN

ATTENTION: RISQUE DE CHOC ELECTRIQUE-NE PAS OUVRIR

• This lightning flash with arrowhead symbol within an equilateral triangle is intended to alert the user to the presence of non-insulated “dangerous voltage” within the product’s enclosure that may be of sufficient magnitude to constitute a risk of electric shock.
• Warning: To reduce the risk of electric shock, do not remove cover (or back) as there are no user-serviceable parts inside. Refer servicing to qualified personnel.
• The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance instructions in the literature accompanying the appliance.

Apparatus with class I construction shall be connected to a mains socket outlet with a protective earthing connection.

Important Safety Precautions

Safety

Please, immediately pull out the AC power plug from adapter if there is an abnormal sound or smell or the LED TV has sound but no picture, and contact after sales support.

The LED TV should be kept free from rain, moisture and dust to prevent electrical shock and short circuits. Do not cover the ventilation openings with table clothes, curtains, newspapers, etc.

The LED TV should be kept from high temperature heating sources or direct sunlight.
Good ventilation is required. Allow 10 cm. between the LED TV and other appliances or built-in cabinet walls.

When you wipe the front cabinet, please make sure the power plug is pulled out and use a soft, dry, lint-free cloth and handle it with care. Do not repeatedly wipe the panel, nor scrap.

Do not wipe the LED TV with any petrol, chemical or alcohol based solvents as it will lead to product damage of the panel and cabinet.

When the television receiver is not used for an extended period of time, it is advisable to disconnect the AC power cord from the AC outlet.

Do not place the LED TV on an unstable surface.

Do not place the power cord or other cables across a walkway in case it is trampled on. Do not overload the power cord or power socket.
When the power plug is used to disconnect and connect the device, it should easily go into the power source.

Do not disassemble the back cover, as it contains high voltages inside and will cause electric shock. Only qualified professionals should conduct internal adjustments, maintenance, and checks.

The TV set should not be subjected to water droplets, vapor, or splash. This equipment should not be placed on objects filled with liquids. Do not place flame sources, such as lit candles, on or near the LED TV. Please, pull out the power plug and contact after sales support if there are abnormal objects or water in the TV.

Pull out the power cord and antenna cable during electrical storms so the LED TV is not damaged by electrical surges. Keep all people away from the antenna cable during electrical storms.

Introduction

Features

Input terminals used for external equipment connection

One AUDIO L/R output One RF input One EARPHONE output Two HDMI input Two USB input One COAXIAL output One RJ45 input.

Accessories

Please make sure the following items are included with your LED TV. If any items are missing, contact your dealer.

• Remote Control

• Batteries (AAAx 2)

• Instructions Manual

• 12V/24V Accessory Plug

• Screw

• Base

Specifications

Without Stand: 501.3 x 48.5 x 296.3 mm
Weight (Net weight)| 2.8 Kg
Operation environment temperature| 0C-35C

Remarks:
The above listed specifications and data are subject to change without prior notice.

Hardware Configuration

CPU: ARM Cortex-A55 quad core
GPU: Mali G31MP2
DDR SIZE: 1.5 GB
eMMC Flash: 8 GB

General Description

Overview of front and side panel

1. SPEAKER

2. REMOTE CONTROL SENSOR

3. POWER INDICATOR
   White: standby mode
   Transparent: power on mode.

4. SOURCE
   Toggles between all the available input sources

5. MENU
   Press to see an on-screen menu of your TV’s features.

6. CH+/-
   Press to change channels.
   In the on-screen menu, use the CH +/- buttons as up/down arrow buttons.

7. VOL+/-
   Press to increase or decrease the volume.
   In the on-screen menu, use the VOL +/- buttons as left/right arrow buttons.

8. PLAY /
   Play/stop DVD (in DVD mode).

9. EJECT /
   Eject DVD.

10. POWER /

Press POWER button to toggle between normal and standby mode.

Overview of back panel

Side port

Port

1. DC 12V
   DC input.

2. RJ45
   Ethernet connection.

3. COAXIAL
   Coaxial Digital audio output.

4. L/R
   Connect to the audio output jacks on your amplifier/home theater.

5. HDMI2
   Connecting for HDMI signal.

6. HDMI1
   Connecting for HDMI signal.

7. RF
   Connected to external antenna to receive the ATV/DTV program in ATV/DTV mode.

8. USB IN
   USB input.

9. EARPHONE
   Connecting for headphone

Assembling Stand Process

Instruction:

1. Place the TV unit on a flat and clean table.
2. Fix stand by 4 pcs screws via screw hole B and A.

Overview of remote control

1. POWER: Turn the TV on and off.

2. Search function.

3. Digital Buttons(0-9, -): Directly select channel with digital buttons.

4. SOURCE: Press to open the input source list.

5. NETFLIX: If network connects, press this key to view NETFLIX directly.

6. Google Play: If network connects, press this key to view Google Play directly.

7. YouTube: If network connects, press this key to view YouTube directly.

8. Prime Video: If network connects, press this key to view Prime Video directly.

9. HOME: Display the HOME page.

10. Arrow button ▲▼◄►: Use to select on-screen menu items and change menu values.

11. MENU: Display the main menu or exit the current menu.

12. OK: Confirms selection.

13. BACK: Return to the previous menu.

14. MUTE: Press this button to cut off the sound of the TV set temporarily, press again to resume.

15. EXIT: Exit the menu.

16. VOL +/- : Press these buttons to adjust the volume.

17. COLOR BUTTONS: It’s used in the APPS.
    Open/close in DVD mode.
    D.MENU: Quick navigation during Teletext or setup settings / DVD: Video DVD Menu button.
    SETUP: DVD system setup.
    D.DISP: Quick navigation during Teletext or setup settings / DVD: DVD Information button.

18. CH∧/∨: Press these buttons to change channel upward or downward.

19. GUIDE: Select electronic program guide, in DTV mode, it will display all the information of program in a week when pressing this button.

20. DIGITAL MEDIA PLAYER CONTROL BUTTON : Include backward, forward, play/pause, stop in USB mode. In DTV mode, press button to record the TV program. Please refer to relevant instructions in the section of multimedia player.

21. LIST: Press to display the channel list.
    A-B: Press the A-B button once to set point A. Press the A-B button a second time to set point B. After setting the program repeat playing from A to B. Pressing the AB button a third time  will cancel the repeat.

22. TEXT: Press to select the teletext mode.
    REPEAT: DVD: Repetition mode button.

23. AUDIO: Press to select mono, nicam, stereo for ATV channel, audio language for DTV channel.

24. SUBT: Open or close subtitle.
    TITLE: Press this button to return to the title of the disc.

Installing Batteries in the Remote Control

Installing Batteries

1. Open the battery compartment cover on the back side.

2. Insert two 1.5V AAA size batteries in correct polarity. Don´t mix old or used batteries with new ones.

3. Closed the cover

Point the remote towards the remote control sensor of the wireless TV and use it within 7 meters.
Put the used batteries into the recycling bin since it can negatively affect the environment.

Note:

• One loading of batteries will last for 1 year under normal use
• If you do not intend to use the remote controller for a long period of time, remove them to avoid damage due to leakage.
• Do not use old and new batteries together.
• The battery (battery or batteries or battery pack) shall not be exposed to excessive heat such as sunshine, fire or the like.

External Connection

Antenna connection

Antenna input impedance of this unit is 75ohm. VHF/UHF 75ohm coaxial cable can be connected to the antenna jack directly, if the antenna cable is 300ohm parallel flat feeder cable, you need to use the 300ohm/75ohm converter to connect the antenna cable to the antenna jack. For details Please refer to the following drawing.

Antennas with 300ohm flat twins Leads

300ohm coaxial cable

Antenna feeder

Antennas with 75ohm Round Leads

75ohm coaxial cable

Antenna cable

External Connection

Connecting DVD Player/Set-Top Box

The rear panel jacks on your TV make it easy to connect a DVD to your TV.

DVD Player/Set-Top Box

Component video separates the video into Y (Luminance (brightness)), Pb (Blue) and Pr (Red) for enhanced video quality.
Be sure to match the component video and audio connections.
For example, if connecting the video cable to COMPONENT IN, connect the audio cable to COMPONENT IN also.
Each DVD player/STB has a different back panel configuration.
When connecting a DVD player/STB, match the color of the connection terminal to the cable.
We recommend the use of cables with a Ferrite Core.

1. Connect a Component Cable between the COMPONENT I [Y N , PB, PR] jacks on the TV and the COMPONENT [Y, PB, PR] jacks on the DVD player.
2. Connect Audio Cables between the COMPONENT IN [R-AUDIO-L] jacks on the TV and the AUDIO OUT jacks on the DVD player.

Connecting DVD Player/Set-Top Box via HDMI

This connection can only be made if there is a HDMI Output connector on the external device.

DVD Player/Set-Top Box

What is HDMI?
HDMI, or high-definition multimedia interface, is a next-generation interface that enables the transmission of digital audio and video signals using a single cable without compression.

Multimedia interface is a more accurate name for it especially because it allows multiple channels of digital audio (5.1 channels).
The difference between HDMI and DVI is that the HDMI device is smaller in size, has the HDCP(High Bandwidth Digital Copy Protection) coding feature installed, and supports multi-channel digital audio.
Each DVD player/STB has a different back panel configuration.
We recommend the use of cables with a Ferrite Core.

1. Connect an HDMI Cable between the HDMI connector on the TV and the HDMI connector on the DVD player/Set-Top Box.

Connecting EARPHONE

1. Plug EARPHONE out connector into EARPHONE out jack on the TV the TV speaker will  be muted.

Supporting signals

Basic Operation

Turning the TV On and Off

How to turn the TV on or off

1. Insert the power cord plug into a polarized D outlet. C
2. Press POWER button on the remote control or button on the LED TV.
3. Normal picture will be displayed on the screen after
4. seconds. If no signal input, “No Signal” will be displayed on the screen.
5. If temporary POWER off is required, press POWER button on the remote control or button on the LED TV.
6. If you want to completely switch off the power for this unit, unplug the power cord plug for this unit.
7. After switching off the unit, you should turn on the TV again at least 5 seconds later.

Status indication lamp
White: standby mode.
Transparent: power on mode.

Auto power-off
If there is no signal input in any Mode, the TV will automatically accesses the standby state in about 15 minutes.

Memory before turning TV off
The settings of picture and the preset channels will be memorized at turning off the unit.
When being started up again, the unit will work according to the mode set before being turned off.

OSD Menu Operations

INITIAL SETUP
This function is used for the remote control pair code. After the code is successful, you can use the Bluetooth remote control to operate the TV.

Press ▲/▼ to select the system language and press OK to confirm the language.

Connect your Android phone to your TV, select “Continue” to continue the connection, and choose “Skip” to skip this step.

Press ▲/▼ to select the wifi to connect, press OK and enter the password to confirm the connection is successful.

By agreeing to automatically send diagnostic information to Google to improve discriminative power, choose “YES” to accept.

1. Your device is powered by Android TV and press the ► button to select the browsing feature.
2. You can get more apps from Google Play and press the ► button to go to the next screen.
3. Transfer photos and other content to the TV via the built-in chromecast, press OK to complete the browsing.

Press ▲/▼ to select the country of your device and press OK to confirm.

HOME SCREEN
After completing the wizard Settings, you can watch TV and go to the home screen.

1. Open Google Assistant or start a text search.
2. Among the applications installed on the TV, the icons for the favourite applications are shown inside here. (Favourite applications can be added/ deleted/changed its order by users.)

Inputs: Icon to select an input source.
Settings: Various settings can be configured here. For details on the settings, see the next explanation.

INPUT SOURCE
In the HOME interface, press ▲/▼/◄/► to select the “Inputs” icon, press OK to open the input source list, then press up to highlight an input and press OK to switch.

Under live TV, press the SOURCE button to display the list of input sources. You can select the desired source.

NAVIGATING THE ON-SCREEN MENU

1. In the HOME interface, press the ► key to select the icon of the circular settings menu, press OK to confirm.

2. Press ▲/▼ button to select what you want set.

3. Press OK to enter setting.

Network

1. Press ▲/▼ button to select what you want set.
2. press OK button to adjust.
3. After finishing your adjustment, press OK button to save and return to the previous menu.

APPS

In this menu, you can set the APP permissions, and read the app lists.

1. Press ▲/▼ button to select what you want set.
2. Press OK button to adjust.
3. After finishing your adjustment, press BACK button to return to the previous menu.

DEVICE PREFERENCES ABOUT

In this menu, you can read the information and settings of TV.

1. Press ▲/▼ button to select what you want set.
2. Press OK button to adjust.
3. After finishing your adjustment, press BACK button to return to the previous menu.

DATE & TIME

Automatic date & time- Press ▲/▼ button to select the option then press OK button to enter the sub-menu.(Optional: Use network-provided time, Off)

• Manually adjusting date & time settings will automatically change the Automatic date & time to OFF.

Set date- Press ▲/▼ button to select the option then press OK button to enter the sub-menu.
Set time- Press ▲/▼ button to select the option then press OK button to enter the sub-menu.
Set time zone- Press ▲/▼ button to select the option then press OK button to enter the submenu.
Use 24-hour format-Press ▲/▼ button to select the option then press OK button to choose ON/OFF.

LANGUAGE

Language- Press ▲/▼ button to select the option then press button to enter the OK select language.

KEYBOARD

Current keyboard- Press ▲/▼ button to select the option then press OK button to enter the sub-menu.
Gboard Settings- Press ▲/▼ button to select the option then press OK button to enter the sub-menu.
Manage keyboards- Press ▲/▼ button to select the option then press OK button to enter the sub-menu.

STORAGE

Internal shared storage- Press ▲/▼ button to select the option then press OK button to enter the sub-menu.
Removable Storage- Press ▲/▼ button to select the option then press OK button to enter the sub-menu.(Note: Show external devices if available)

HOME SCREEN

In this menu, you can set channels, apps, open source licenses.

1. Press ▲/▼ button to select what you want set.
2. Press OK button to adjust.
3. After finishing your adjustment, press BACK button return to the previous menu.

GOOGLE

In this menu, you can set searchable apps, safe search filter, block offensive words, open source licenses.

1. Press ▲/▼ button to select what you want set.
2. Press OK button to adjust.
3. After finishiing your adjustment, press BACK button return to the previous menu.

CHROMECAST BUILT-IN

In this menu, you can read the information and settings of Chromecast.

1. Press ▲/▼ button to select what you want set.
2. Press OK button to adjust.
3. After finishing your adjustment, press BACK button return to the previous menu.

SCREEN SAVER

Screen saver- Press ▲/▼ button to select the option then press OK button to enter the
sub-menu.(Optional: Turn screen off, Backdrop, Colors) When to Start- Press ▲/▼ button to select the option then press OK button to enter the
sub-menu. (Optional: 5 minutes, 15 minutes, 30 minutes, 1 hour, 2 hours.)
Start now – Press ▲/▼ button to select the option then press OK button to enter screen saver.

ENERGY SAVER

Turn off Display- Press ▲/▼ button to select the option then press OK button to enter the sub-menu. (Options: 15 minutes, 30 minutes, ….24 hours, Never.).

LOCATION

Location status- Press ▲/▼ button to select the option then press OK button to enter the sub-menu. (Optional: Use Wi-Fi to estimate location, Off).

USAGE & DIAGNOSTICS

Usage & diagnostics- Press ▲/▼ button to select the option then press button OK to choose ON/OFF.

ACCESSIBILITY

Captions- Press ▲/▼ button to select the option then press OK button to enter the submenu.
High contrast text- Press ▲/▼ button to select the option then press OK button to choose ON/OFF.
Text to speech- Press ▲/▼ button to select the option then press OK button to enter the sub-menu.
Accessibility shortcut- Press ▲/▼ button to select the option then press OK button to choose ON/OFF.
TalkBack- Press ▲/▼ button to select the option then press OK button to enter the submenu.
Switch Access- Press ▲/▼ button to select the option then press OK button to enter the sub-menu.

RESTART
Press OK button to enter the sub-menu. Restart the TV.

ADD AND USE OF MEDIA PLAYER

1. In the HOME interface, select the + icon in the APP column to add the application, and click OK.
   Press up and down to select the Media Player application, and click to add it OK to the HOME interface.

2. Focus on the corresponding USB driver and press OK to display video, photo, audio files.
   Press navigation button to select the file.

PICTURE

Picture Mode- Press ▲/▼ button to select the option button to enter the submenu.(Optional: Standard, Dynamic, Movie, Eye Comfort, Gentle, Vivid, Sport, Personal).
Brightness/Color Saturation/Hue/Contrast/Gamma/Black Level SharpnessPress ▲/▼ button to select the option.
Press ◄ to decrease the parameter. Press ► to increase the parameter.
Gamma- Press ▲/▼ button to select the option.
Press ◄ to decrease the parameter.
Press ► to increase the parameter.

ECO
Press MENU key to the main menu, and select Picture.
Press button to ECO option and press OK to select the option.

SOUND

Press MENU key to the main menu, and select Sound.
Sound Mode- Press OK to enter the sub-menu, press button to select option and press OK to select the option.
Pure Sound- Press ▲/▼ button to select the option then press OK button to choose ON/OFF.
Surround- Press ▲/▼ button to select the option then press OK button to choose ON/OFF.
Sound Only- Press OK to enter the sub-menu, press OK button to select option.
Output Device- Press ▲/▼ to enter the sub-menu.
Audio Output Type- Press ▲/▼ to enter the sub-menu.
Advanced Settings- Press ▲/▼ to enter the sub-menu.
Press MENU key to the main menu, and select System.
Press ▲/▼ button to select option and press OK to select the option.
**SYSTEM

**

SOURCE
Press the “SOURCE” button menu. The up and down direction keys can be selected, or Press the left or right button to select the DVD, and press the Enter button to enter. Press the DVD SETUP button to enter that
function.

TV SYSTEM
Set the options: NTSC/PAL/AUTO.
POWER RESUME
Press the ENTER function on or off.
TV TYPE
Set the screen ratio options: PS(4:3 Pan Scan), Normal/PS(4:3 Letter Box), and Wide (16:9) the default setting is wide.
PASSWORD
Enter “0000” to enter.
RATING
Disc Options.
DEFAULT
This option will return the DVD to its factory default settings.

DVD

OSD LANGUAGE
Set the OSD Language options.
AUDIO LANG
DVD language selection options.
SUBTITLE LANG
This player can display DVD subtitle languages if supported by the DVD disc. When playing DVD’s you can hide the subtitle or choose any of them as the current subtitle language.
MENU LANG
Set the MENU Language options.

AUDIO OUT
Press the “ENTER” Key. The up and down direction keys can be used for selection.
KEY
Press the “ENTER” Key. The up and down direction keys can be used for selection.

DUAL MONO
Press the “ENTER” Key. The up and down direction keys can be used for selection.

Troubleshooting

If you have any problem, check the countermeasures for each symptom listed below. The following symptoms may have caused by inappropriate adjustment rather than act- ual malfunction of the unit. If the trouble persists, contact the service center.

cord and restart the TV.
No picture| Check antenna connection.Station may experience problems, please tune to another station.Please adjust the settings of contrast and brightness.
Good picture
but no sound| Increase the volume.please check sound settings.
Good sound but abnormal color or no picture| Check the antenna connection.
No remote control| No support for this function.
Full screen flickering under VGA| V•HEIGHT value may be set too big, restart computer and enter safe mode, then set monitor parameters to correct value according to adjustment description.
Horizontal stripes under VGA| Sample phase may be deflected, adjust phase according to picture position.
Colored dots may be present on the screen| This product is the high resolution LED display device and a few cell defects can occur in the manufacture of the LED. Several colored dots visible on the screen would be accep­table.in line with other LED manufacturers and would not mean that the LED is faulty. We hope you will understand that it could not be changed or refunded.

Picture defects and the reason

Snowy Picture
Snowy picture is usually due to weak signal. Adjust antenna or install an antenna amplifier.

Double Image or Ghosts
Double images are usually caused by reflections from tall buildings. Adjust the direction of the antenna or raise it.

Radio Wave Interference
Wave patterns are moving on the screen, which are usually caused by nearby radio transmitters or short- wave receiving equipment.

High Temperature Hydrothermal Interference
Diagonal or herringbone patterns appear on the screen or part of picture is missing. This is probably caused by high temperature electrothermal equipment in a nearby hospital.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>