CISCO IC3000 Industrial Compute Gateway User Guide

: June 16, 2024
: Cisco

Table of Contents

Initial configuration
Read User Manual Online (PDF format)
Download This Manual (PDF format)

Initial configuration

Cisco IC3000 front view

Before starting, take a moment to note and unscrew the following parts you’re going to use during the procedure.

DC-in connectors (1)
Serial number (2)
Reset pinhole (3)
SYS LED (4)
Console connectors (5) : RJ-45 and mini-USB
USB port 2 (6)
MGMT Ethernet port (7) : Local Manager and Collection network interfaces
Industrial Network Interfaces (8) : 2x RJ45 10/100/1000 BaseT connectors and 2x SFP fiber ports

Connect the Cisco IC3000

The Cisco IC3000 contains 4 independent ports which can be used to capture in SPAN mode or to do active scanning on the network. Depending on the port usage the corresponding switch port must have the right configuration (SPAN or access).

The Cisco IC3000’s Industrial network interface to do the dPI is to be connected to switches configured in port mirroring only.

To connect the network interfaces to the Cisco IC3000:

Procedure

Step 1 Connect the Collection network interface (IC3000 to Center) to the MGMT ENET port (1).
Step 2 Connect the Industrial network interface (IC3000 to on-site switches) to ports 1, 2, 3, 4 (up to 4 switches configured in port mirroring or access depending on the port usage).
Step 3

Ports 1 and 2 are RJ45 10/100/1000 BaseT Connectors ( 2 ).
Ports 3 and 4 are SFP fiber ports ( 3 ).

Connect to the Cisco IC3000 with the serial console

This section describes how to establish a connection to the Cisco IC3000 from Windows 10 using PuTTY. It is required to perform a sensor management extension installation and to enable Active Discovery (optional) when performing a manual installation.

Note This procedure will also work for other versions of Windows.

Requirements:

A RJ45 or mini USB console cable.
A serial console emulator, like PuTTY.

To connect a console to the Cisco IC3000:

Procedure

Step 1 Download and install on your computer a serial console emulator like PuTTY. Refer to its own documentation to use it.
Step 2 Connect your computer to the Cisco IC3000 through its serial port using the RJ45 or mini USB console cable. If you are using Windows , you need to identify to which COM port the console is connected.
To identify the COM port:
Step 3 Right click on the Windows Start icon and select “Device Manager”.

Step 4 Scroll down and click “Ports (COM & LPT)” menu. The COM number appears.

To start a connection to the Cisco IC3000:

Step 5 Make sure there is no USB drive plugged into the Cisco IC3000.
Step 6 Disconnect the Cisco IC3000 from the DC Current source.
Step 7 Open PuTTY.

The following screen appears:

Step 8 Select Serial for the Connection type.
Step 9 Enter “COM” into the serial line field. Set speed at 9600.
Step 10 Click Open to display the shell prompt for PuTTY.
Step 11 Connect the Cisco IC3000 to the DC current source.

Wait a few moments. When booting is complete, the shell prompt will ask you to press return to start. The connection has established with success.

Cisco IC3000 platform initial configuration

Perform the following procedure if it’s the first time the Cisco IC3000 device is installed in Cisco Cyber Vision.

Set Cisco IC3000 for Local Manager

Procedure

Step 1 Click Manage Cisco devices , then Generate Day-0 config for IC3000.

Step 2 Fill the following fields to set the Local Manager’s network parameters and login:

The Host Management’s IP address, netmask and gateway. They must be set to access the Local Manager of the Cisco IC3000 device.
The Local Manager admin user name. The login is “admin” by default. You must use the default login in case a factory reset is performed and thus to avoid starting the whole procedure again.
The user name will be asked later to log in to IOx Local Manager and in case of troubleshooting and configuration. Therefore, make sure to keep this piece of information stored.

Step 3 Click Generate.
The file device_config.cfg is downloaded.

Prepare and import the Local Manager configuration file

After generating and downloading the file device_config.cfg you must prepare and import it in the Cisco IC3000.

Procedure

Step 1 Copy the file in a folder named as the serial number of the Cisco IC3000 (e.g. FCH2309Y01Z). The folder must be placed at the root directory of a USB drive formatted as FAT32.

Step 2 Disconnect the Cisco IC3000 from the DC Current source. The USB drive must be plugged at the Cisco IC3000 boot.
Step 3 Plug the USB drive on port 2 of the Cisco IC3000.
Step 4 Connect the sensor to the DC Current source.
Wait a few moments. The Cisco IC3000 status changes to Enrolled on the Cisco Cyber Vision GUI.
Step 5 Unplug the USB drive from port 2.

The Local Manager should become available on the IP address defined during this procedure.