Motive OC1 AI Omnicam Security Camera Installation Guide
- June 16, 2024
- motive
Table of Contents
AI Omnicam
Installation guide
**** Warning
Failure to properly affix the device to the vehicle can cause the device to
detach and result in serious injury.
Similarly, bolts, nuts, screws, the mount, and other mechanical components
used to affix the device to the vehicle can loosen, break, and fail over time
which can also cause the device to detach and result in serious injury.
Read and follow all installation and safety instructions provided in the quick
start guide and support articles. Regularly inspect the camera, bolts, nuts,
screws, the mount, and mechanical components to ensure they are in good
working order and remain properly affixed to the vehicle.
You are responsible for securing the mount and camera to your vehicle,
checking the hardware prior to use, and periodically inspecting the products
for adjustment, wear, and damage.
If you do not understand all of the instructions and cautions, or if you have
no mechanical experience and are not thoroughly familiar with the installation
procedures, you should have the product installed by a professional installer.
Safety & Privacy
The Motive AI Omnicam is a driver and fleet management aid only. It is not a
substitute for safe, conscientious driving and cannot compensate for
distracted, inattentive, or impaired driving. All warning and alert features
provided by Motive products are for informational purposes only. No warning or
alert feature provided by Motive products are intended to replace your
responsibility to observe all road and driving conditions, abide by all traffic
regulations, and use safe driving judgment at all times.
Video recordings made by the Motive AI Omnicam are for personal or internal
use only.
The Motive AI Omnicam uses artificial intelligence to identify animate and
inanimate objects in video and images, potentially including individual
persons, and the data captured by the AI Omnicam may be used in the creation
and production of other Motive products and services.
In some jurisdictions it could be considered an invasion of privacy rights to
take or publicly display photographs or videos of people or their vehicles
using this product or to publish or reproduce such photographs or videos.
Further, some jurisdictions may have laws governing the collection, use,
storage, and destruction of a person’s biometric information, including face
geometry and voiceprint. It is your responsibility to know and comply with
applicable laws and rights to privacy in your jurisdiction, including
obtaining proper consents and authorizations. Covered by patents at
patentlist.accessadvance.com
Installation instructions
AI Omnicam requires a mount kit for installation. Currently, it comes with the
AI Omnicam Body Mount.
Download the Motive Fleet App and go to the Devices tab for step by step
installation instructions.
For more information go to gomotive.com/omnicam-install
More mount kits will be available in the future.
Understanding LEDs
| Solid white
The device is recording
---|---
| Flashing white (slow)
The device is starting/booting up
| Flashing white (fast)
The device is in error state. For troubleshooting, please check gomotive.com
/omnicam-install
Common AI Omnicam use cases
Side (Right & Left)
Rear
Cargo
Passenger
Motive AI Dashcam or Smart Dashcam is used as the road or driver facing
camera.
Support for rear, cargo and passenger use cases coming soon.
Note
Product was validated using suite of reliability tests that were guided by the
standards below:
- ISO-16750-3
- ISO-16750-4
- ISO 16750-5
- IEC 60529
- IEC 60068-2-5
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the equipment.
- Increase the separation between the equipment and receiver.
- Consult the dealer or an experienced radio/TV technician for help.
This equipment complies with FCC RF radiation exposure limits set forth for an
uncontrolled environment and RSS 102 RF exposure compliance requirements. This
equipment should be installed and operated with a minimum distance of 20
centimeters between the radiator and your body. This Transmitter must not be
co-located or operating in conjunction with any other antenna or transmitter.
Changes or modifications not expressly approved by Motive could void the user’s
authority to operate this equipment.
This device contains license-exempt transmitters / receivers that comply with
Part 15 of the FCC Rules and with Innovation, Science and Economic Development
Canada’s license-exempt RSS(s). Operation is subject to the following two
conditions: (1) this device may not cause harmful interference, and (2) this
device must accept any interference received, including interference that may
cause undesired operation.
This device complies with part 15 of the FCC Rules. Operation is subject to
the following two conditions: (1) This device may not cause harmful
interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
Troubleshooting
855-434-3564
support@gomotive.com
help.gomotive.com
Resources
Scan this code or visit gomotive.com/omnicam-install for detailed information and recommendations on installing and assigning your AI Omnicam.
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>