EMERSON EPB-3005 Stereo Radio Cd Speaker Instruction Manual

: June 16, 2024
: Emerson

Table of Contents

IMPORTANT NOTES
LOCATION OF CONTROLS
NAMES OF CONTROLS
CD/MP3 OPERATION
SELECTING A DESIRED TRACK/PASSAGE
PROGRAMING TRACKS
Read User Manual Online (PDF format)
Download This Manual (PDF format)

EMERSON EPB-3005 Stereo Radio Cd Speaker Instruction Manual

IMPORTANT: Please read before using and keep for future reference.

IMPORTANT NOTES

CAUTION
Use of controls or adjustment or performance of procedures other than those specified herein may result in hazardous radiation exposure.

DANGER

This Compact disc player is classified as a Class 1 LASER PRODUCT.
THE CLASS 1 LASER PRODUCT label is located on the rear exterior.

NOTE: The manufacturer is not responsible for any radio or TV interference caused by unauthorized modifications.

Avoid installing the unit in locations described below:
1. Places exposed to direct sunlight or close to heat radiating appliances such as electric heaters, or other equipments that radiate too much heat.
2. Places subjected to constant vibration.
3. Unventilated or dusty places.
4. Humid or moist places.
Operate buttons and switches as instructed in the manual.
Before turning on the power for the first time, make sure that the adaptor is properly installed and the voltage switch is correctly set.
Store your CD or other devices in a cool area to avoid damage from heat.

CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO DOT REMOVE COVER (OR BACK). DO NOT OPEN THE UNIT. ANY SERVICING PLEASE REFER TO QUALIFIED SERVICE PERSONNEL.
WARNING:

Remove batteries if exhausted or if they will not be used for a long period.
The incorrect use of batteries can cause electrolyte leakage and will corrode the compartment or cause the batteries to burst. Therefore:
Do not mix battery types, e.g. alkaline with zinc carbonate.
When inserting new batteries, replace all batteries at the same time.

LOCATION OF CONTROLS

NAMES OF CONTROLS

DISPLAY
SPEAKER DECORATION RING
LEFT/RIGHT SPEAKERS
HEADPHONE JACK
SD CARD SLOT
USB PORT
PAIR/STANDBY INDICATOR
AUX IN JACK
PASSIVE SPEAKER DECORATION RING
VOLUME KNOB
FUNCTION BUTTON
EQ/LIGHT BUTTON
PROG./P-MODE BUTTON
BACK/FAST BACKWARD/-10 BUTTON
CD DOOR
NEXT/FAST FORWARD/+10 BUTTON
STOP BUTTON
PLAY/ PAUSE/ PAIR BUTTON
STANDBY BUTTON
TUNING KNOB
ANTENNA
LEFT/RIGHT PASSIVE SPEAKERS
HANDLE
BATTERY COMPARTMENT
DC IN JACK

POWER SOURCE
DC INPUT OPERATION
Plug the tail of supplied adaptor into DC IN Jack on unit and the plug into household AC outlet.
The batteries will be automatically disconnected

DC OPERATION
Open the BATTERY COMPARTMENT DOOR. Install 8pcs UM-1/D size batteries (not included) into compartment. Please follow correct polarities as indicated.

CAUTION:
Remove batteries if they are flat or not being used for a long period of time.
Batteries contain chemical substances, so they should be disposed of properly.

BASIC FUNCTION SWITCHING ON THE UNIT
After connecting the power, press STANDBY button on the unit. Press the FUNC. button to choose CD/FM/AM/USB/SD CARD/BLUETOOTH or AUX function.

VOLUME ADJUSTING
Rotate the VOLUME knob on the unit to increase or decrease volume.

EQ FUNCTION
This unit has a built-in equalizer system, Press EQ/LIGHT button on the unit while playing to select different music style (sound tone): FLAT, CLASSIC, ROCK, POP and JAZZ.

HEADPHONE JACK
For private listening, insert a 3.5mm headphone (not included) into the HEADPHONE jack. The SPEAKER output would be automatically cut off.
CAUTION: LISTENING AT A HIGH VOLUME OVER A LONG PERIOD IS NOT GOOD FOR YOUR EARS.

DISCO LIGHT
There are five flashing modes of the disco light, press and hold the EQ/LIGHT button on the unit to choose the desired mode: “LIGHT 01” to “LIGHT 05”. To turn off the disco light, press and hold the EQ/LIGHT button on the unit until “LIGHT OFF” shows on the display.

RADIO OPERATION TUNING RADIO STATIONS

Press the FUNC. button on the unit to select FM or AM FUNCTION.
Tune to desired station by rotating the TUNING knob, the display will show the band frequency. Example: FM 97.10 MHz, or AM 520 KHz.
Extend FM TELESCOPIC ANTENNA to its full length and gently move the unit back and forth to get the best reception, or place the unit in an open location.
To turn off the radio, press the FUNC. button on the unit to switch to other functions or press STANDBY button on the unit to turn off the unit

RADIO AUTO SCAN (SEARCH)
Press and hold the /PAIR button on the unit, the unit will conduct auto scan and program until having found a strong signal. The unit will start to broadcast the P01 after searching finished.
Press the /+10 or /-10 button on the unit to choose next programmed station.
RADIO STATION MEMORY OPERATION
You may pre-store radio stations in memory for your preference (30 FM stations/10 AM stations), so as you can listen to your desired station directly and quickly, no need to tuning and search for again.

Rotate the TUNING knob on the unit to select a desired station.
Press the PROG/P-MODE button on the unit, “P01”, “MEM” will show on the display.
Press TUN-/ or TUN+/ button to choose the desired sequence you want to store, then press the PROG/P-MODE button on the unit to confirm.
Search another station, repeat steps (1), (2) & (3) until all desired stations stored. Up to 30 stations can be programmed.
Press the /-10 or /+10 button on the unit to listen to the stored station directly.

CD/MP3 OPERATION

Discs for Playback
This system can playback all digital audio CD/MP3, finalized digital audio CD- Recordable (CD-R) discs, finalized digital audio CD-Rewritable (CD-RW) discs and CD-DA format digital audio CD/CD-R/CD-RW discs.

LOADING A DISC

Press the FUNC. button on unit to select “CD” mode.
Press the PUSH TO OPEN button to open the CD door, “OPEN” will be shown on the display.
Place an audio CD/MP3 DISC into the tray with the front side facing up.
Close the CD door.
The display will show a flashing “TOC READ”, then the total number of tracks would be shown and the playback will start from track.
To remove the CD, press STOP button on the unit to turn off the unit, then press the
PUSH TO OPEN button to open the CD compartment lid. Hold the CD by its edges, and take it out carefully.

Note:

Make sure the disc is stopped before opening the CD DOOR.
To ensure good system performance; wait until the unit completely reads the disc before proceeding.
If no disc loaded into the tray, or the disc is unreadable, the display will show “NO DISC”.

PLAYING A DISC

The playback starts from track 1 automatically when reading the disc.
To pause playback, press / PAIR button on the unit. The current playing time will flash
on the display.
To resume playback, press / PAIR button on the unit again.
To stop playback, press STOP button on the unit, the total number of tracks will show on the display.

SELECTING A DESIRED TRACK/PASSAGE

To select a desired track
Press the /+10 or /-10 button on the unit on stop mode or during playing until the desired track appears on the display.

To search for a particular passage during playback (track scanning at high speed)
Press and hold the /+10 or /-10button on the unit to scan the current playing track at high speed until desired point (passage) appears, then release the button for normal playback mode. Playback will start again from this point.

To select a song which track number exceeds 10（for MP3 disc only）
To select a song/track which number exceeds 10, press and hold the /+10 or /-10 button on unit in stop mode to skip forward 10 tracks, then press the /+10 or /-10button on the unit to select desired track.

PROGRAMING TRACKS

Programming tracks of disc are possible when playback is stopped. Up to 20 tracks for CD disc and 99 tracks for MP3 disc can be stored in the memory in any order.

In stop mode, press the PROG./P-MODE button on the unit to enter program setting, the PROG logo will be shown on the display and show P01.
Press the /+10 or /-10 button on the unit to select the first desired track to be programmed. (example: track 2)
Press the PROG./P-MODE button on the unit to enter. The display would show PROG and P02.
Repeat steps 2 & 3 to store other desired tracks until all tracks programmed.
Press the /PAIR button on the unit to start playback from the first programmed track.
Press the STOP button on the unit to stop program playback.

To clear the program, you may press **STOP** button on the unit when the disc stopped and open the CD compartment lid, the program will be erased.

REPEAT PLAY
You can play one track or all tracks on the disc repeatedly.

To Repeat a Single Track

Press PROG./P-MODE button on the unit during play, the display will show a steady “ ” and the current track will be played over and over again till you press the STOP button on the unit.
To cancel repeat play, press PROG./P-MODE button on the unit until “ ” disappears from the display.

To repeat all the Tracks

Press PROG./P-MODE button on the unit until the “ **ALL”** shows steadily on the display, all tracks on the disc will be played over and over again till you press the STOP button on the unit.
To cancel repeat play, press the PROG./P-MODE button on the unit until “ **ALL”** disappears from the display.

/+10 or /-10