YAMAHA YZ 450F 2019-2022 Riding Rally Bike Owner’s Manual
- June 16, 2024
- Yamaha
Table of Contents
YAMAHA YZ 450F 2019-2022 Riding Rally Bike
Product Information
Specifications
- Brand: AiM InfoTech
- Product: Yamaha YZ 450F 2019-2022 YZ 250F from 2019 Release 1.00
- Supported Models and Years:
- YZ 250F: From 2019 onwards
- YZ 450F: 2019 – 2022
- Kit Content and Part Number: Yamaha YZ 250F and YZ 450F kit for Solo 2DL part number is V02589170CS
Installation and Connection
- Remove the original bar pad from your Yamaha YZ-F bike.
- Install the AiM bar pad.
- Connect the Solo 2DL using the Sumitomo female connector located on the left side of the bike.
Race Studio 3 Configuration
Before connecting the AiM device to the ECU, make sure to set all functions
using the AiM software Race Studio. The following parameters need to be set in
the device configuration:
| Channel Name | Function |
|---|---|
| RPM | Engine RPM |
| TPS | Throttle position sensor |
| Water Temp | Water temperature |
| Air Temp | Air temperature |
| MAP | Manifold air pressure |
| Battery Voltage | Battery voltage |
| Tot Run Time | Total running time |
| FlagError | Flag error |
| Error | MIL (Malfunction Indicator Lamp) error |
Technical note: Not all data channels outlined in the ECU template are validated for each manufacturer’s model or variant. Some of the outlined channels are model and year specific and may not be applicable.
FAQ (Frequently Asked Questions)
Q: What models and years are supported by the Yamaha YZ 250F and YZ 450F
kit for Solo 2DL?
A: The supported models and years are YZ 250F from 2019 onwards and YZ 450F
from 2019 to 2022.
Q: What is the part number of the Yamaha YZ 250F and YZ 450F kit for Solo
2DL?
A: The part number is V02589170CS.
Q: How do I install the Solo 2DL on my Yamaha YZ-F bike?
A: To install the Solo 2DL, follow these steps:
- Remove the original bar pad from your Yamaha YZ-F bike.
- Install the AiM bar pad.
- Connect the Solo 2DL using the Sumitomo female connector located on the left side of the bike.
Q: What parameters do I need to set in Race Studio 3 configuration?
A: The parameters to set in Race Studio 3 configuration for Yamaha YZ-F
are:
- RPM: Engine RPM
- TPS: Throttle position sensor
- Water Temp: Water temperature
- Air Temp: Air temperature
- MAP: Manifold air pressure
- Battery Voltage: Battery voltage
- Tot Run Time: Total running time
- FlagError: Flag error
- Error: MIL (Malfunction Indicator Lamp) error
Q: Are all the data channels outlined in the ECU template applicable for
every model and year?
A: No, not all data channels outlined in the ECU template are validated for
each manufacturer’s model or variant. Some of the outlined channels are model
and year specific and may not be applicable.
Models and years
This document explains how to connect the Solo 2 DL to the vehicle Engine
Control Unit (ECU) data stream.
Supported models and years are:
- YZ 250F
- YZ 450F
- from 2019 onwards 2019 – 2022
Kit content and part number
Yamaha YZ 250F and YZ 450F kit for Solo 2DL part number is: V02589170CS.
- 1 Bar Pad for bikes without cross brace for Solo 2DL with thermoformed cover, Velcro already mounted and fixing plate (1)
- 4 – 3×12 screws (2)
- 1 cable for Yamaha YZ-F (3)
Yamaha YZ-F cable (3) – part number V02589170 – and Bar Par for Solo 2DL (1) – part number X47KPSOLO2T10 – can be bought separately as spare parts.
The draw here below shows constructive scheme of cable V02589170.
Installation and connection
To install Solo 2DL on your Yamaha YZ-F remove the original bar pad and
install AiM bar pad. Images here below show the original bar pad on the left
and AiM one on the right. 
To install the Solo 2DL on Yamaha YZ-F
bikes use the Sumitomo female connector placed left on the bike as highlighted
in the picture below.
Race Studio 3 configuration
Before connecting the AiM device to the ECU, set all functions using AiM
software Race Studio. The parameters to set in the device configuration are:
- ECU manufacturer:
- ECU Model:
- YAMAHA YZ-F (RS3 only)
”YAMAHA – YZ-F” protocol
Channels received by Solo 2DL configured with “YAMAHA – YZ-F” protocol are:
CHANNEL NAME FUNCTION
- RPM Engine RPM
- TPS Throttle position sensor
- Water Temp Water temperature
- Air Temp Air temperature
- MAP Manifold air pressure
- Battery Voltage Battery voltage
- Tot Run Time Total running time
- FlagError Flag error
- Error MIL
Technical note : not all data channels outlined in the ECU template are validated for each manufacturer’s model or variant; some of the outlined channels are model and year specific, and therefore may not be applicable.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>