PURE Highway 300Di Upgrading The Radio Software Via USB User Guide

: June 15, 2024
: Pure

Table of Contents

PURE Highway 300Di Upgrading The Radio Software Via USB
Product Information
Specifications
Product Usage Instructions
Software via USB
Windows 2000\ XP
Windows 7\ Vista
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

PURE Highway 300Di Upgrading The Radio Software Via USB

Product Information

The product mentioned in the user manual is a Pure radio that requires a software upgrade. It is important to note that these instructions are only applicable to radios in full working order and for voluntary software upgrades. If your radio is displaying a fault message and waiting for an upgrade, you should refer to the specific instructions provided in the article ‘Waiting for an upgrade…’. Please note that this FAQ does not apply to the following products: Jongos, Sensia 200D Connect, Evoke F4 with Bluetooth, Contour 200i Air, Contour i1 Air, Highway 300Di, Highway H260DBi, and Avalon. For instructions to update these products, please visit the downloads and user guides section on our website and select your product to access the appropriate instructions.

These instructions are specifically for products that can only be updated using a 32-bit Windows operating system. If the software page for your product indicates a Mac or 64-bit Windows update, please disregard this FAQ and follow the on-screen instructions provided with the software update.

Specifications

Compatible Operating Systems: Windows XP (32 bit), Windows Vista (32 bit), Windows 7 (32 bit)
Mac OS systems are not supported
USB Lead: USB A to B lead or USB A to Mini B lead (depending on your radio model)

Product Usage Instructions

Checklist
Before starting the software update process via USB, please ensure the following requirements are met:

A Windows-powered PC running Windows XP (32-bit), Windows Vista (32-bit), or Windows 7 (32 bit).
64-bit Windows systems are not supported.
Mac OS systems are not supported.
A USB lead (USB A to B lead or USB A to Mini B lead, depending on your radio model).
Remove all batteries and battery packs from your Pure product before updating.
Your Pure product must be connected to mains power during the software update.
Ensure that the software update you download is the correct version for your PURE product and that it is not an older version than your current software.
Compare your product’s current software version with the new version before installing.

If you have all of the above requirements in place, you can proceed with the software installation process without any issues.

Windows 2000/XP
Please follow the steps below to update your Pure radio using a Windows 2000/XP operating system:

Do not connect your radio to your computer via USB until instructed to do so by the software update package. If you have already connected your radio, disconnect the USB cable and reboot both the radio and the computer.
Open your web browser and visit the downloads website to locate the software download for your product. The software download file will have a name similar to ‘the_name_of_your_radio_version_number.exe’ and will be underlined. Save the software update package to a location on your PC where you can easily find it.
Once the download is complete, double-click the file to start the installation process. You may need to confirm any Windows security prompts to allow the process to run.
At the welcome screen, click the ‘Next’ button.
At the ‘Software License’ screen, click ‘Yes’ to accept.
At the ‘Connect USB Cable’ screen, click ‘Next’.
The Pure software update package will now install its software onto your radio. Click the ‘Next’ button to start the upgrade. Please be patient as this process may take up to 5 minutes. Do not touch or turn off your radio during the update process.

FAQ

Q: Which products are not covered by these instructions?
A: These instructions do not apply to Jongos, Sensia 200D Connect, Evoke F4 with Bluetooth, Contour 200i Air, Contour i1 Air, Highway 300Di, Highway H260DBi, and Avalon. Please refer to the downloads and user guides section on our website for instructions specific to these products.
Q: Can I use a Mac or a 64-bit Windows system for the software update?
A: No, these instructions are only applicable to Windows XP (32 bit), Windows Vista (32 bit), or Windows 7 (32 bit) operating systems. Mac OS systems and 64-bit Windows systems are not supported. If the software page for your product indicates a Mac or 64-bit Windows update, please follow the on-screen instructions provided with the software update.

Software via USB

General Questions

Laura – 2021-10-05 –
Please note – this guide assumes your radio is in full working order and you are performing a voluntary software upgrade. If your radio appears to have suffered a failure and is displaying a fault message advising you that it is waiting for an upgrade, you should follow the instructions found in the article ‘Waiting for an upgrade…’

This FAQ does not apply to Jongos, Sensia 200D Connect, Evoke F4 with Bluetooth, Contour 200i Air, Contour i1 Air, Highway 300Di, Highway H260DBi, and Avalon. For instructions to update these please go to the downloads and user guides section. You can select your product and instructions will be listed.

These instructions are only used for products in our range that can only be updated by Windows 32 bit Windows operating systems If the software page for your product states that there is a Mac or 64-bit Windows update please ignore this FAQ and just run the software update, you will be prompted with on-screen instructions as the update runs.

Checklist…

Before starting – there are several requirements needed to ensure a successful software update via USB:
You need a Windows-powered PC running Windows XP(32-bit), Windows Vista (32-bit), or Windows 7 (32-bit). 64-bit Windows systems are not currently supported in this process. Mac OS systems are not supported in this process.
You will need a USB lead. Depending on your radio, this will either be a USB A to B lead o a USB A to Mini B lead.
Make sure you remove all batteries and battery packs before updating your Pure product. Your Pure product must be running on mains power while performing a software update.
Make sure the software update you download is the correct software for your PURE product, and that you are not backdating your current software version.
Compare your product’s current software version with the new version before installing.
OK, that’s the checklist done. If you have all of the above in place then you should have no problems installing new software on your Pure product.

Windows 2000\ XP

Please note
Do not connect your radio to your computer via USB until instructed to by the software update package. If you have already connected your radio you should disconnect the USB cable and reboot both the radio and the computer in preparation.

Open your web browser go to the downloads website and locate your product software download. The software download always looks something like the_name_of_your_radio_version_number.exe’ and is underlined. When downloading, make sure you save your software update package to a location on your PC where you will be able to easily ﬁnd it. On completion of the download, double-click the ﬁle to start the installation process. You may need to conﬁrm any Windows security prompts to allow the process to run.
At the welcome screen press the button marked ‘Next’.
At the ‘Software Licence’ screen press ‘Yes’ to accept.
At the ‘Connect USB Cable’ screen, press ‘Next’.
Now you can go ahead and connect your radio to your PC via the USB cable – using the USB socket on the side or the back of the radio.
Connecting your radio to your PC may now start the Windows ‘Found New Hardware’ wizard to identify the radio attached. You will be prompted with an option to search Windows Update for drivers, as the drivers were installed when you started the update wizard, you can decline this and continue the wizard. You then will be given the option to insert an installation disc, just select ‘Install the device driver automatically’ and click
‘Next’. If you’ve plugged your radio in at the right time the drivers will install and your radio should register as a device on your computer.
The Pure software update package can now install its software onto your radio and will prompt you to press the ‘Next’ button to start the Upgrade. Click the ‘Next’ button to start the upgrade. This may take as long as 5 minutes so please be patient with it and do not touch or turn oﬀ your radio during the update process.
From this point onwards you should be able to follow any onscreen instructions to complete the process. Clicking ‘Finish’ at the end of the process will re-boot your radio and the recovery process is complete.

Windows 7\ Vista

( 32 bit only)

Please note
Do not connect your radio to your computer via USB until instructed to by the software update package. If you have already connected your radio you should disconnect the USB cable and reboot both the radio and the computer in preparation.

Open your web browser and go to http://support-uk.pure.com/downloads and locate your product software download. The software download always looks something like the_name_of_your_radio_version_number.exe’ and is underlined. When downloading, make sure you save your software update package to a location on your PC where you will be able to easily ﬁnd it. On completion of the download, right-click the software update package and select ‘Run
As Administrator, and conﬁrm any Windows security prompts as necessary.
At the welcome screen press the button marked ‘Next’.
At the ‘Software Licence’ screen press ‘Yes’ to accept.
At the ‘Connect USB Cable’ screen, press ‘Next’.
Now you can go ahead and connect your radio to your PC via the USB cable – using the USB socket on the side or the back of the radio.
Connecting your radio to your PC may now start the Windows ‘Found New Hardware’ wizard to identify the radio attached. Complete this process to allow the PURE update package to continue. You may see a taskbar message conﬁrming that your radio has been installed successfully and again you may need to conﬁrm any Windows security prompts as necessary.
The Pure software update package can now install its software onto your radio and will prompt you to press the ‘Next’ button to start the Upgrade. Click the ‘Next’ button to start the upgrade. This may take as long as 5 minutes so please be patient with it and do not touch or turn oﬀ your radio during the update process.
From this point onwards you should be able to follow any on-screen instructions to complete the process. Clicking ‘Finish’ at the end of the process will re-boot your radio and the recovery process is complete.

Note : At the end of the process You may need to conﬁrm to Windows that the installation was successful. You may need to reset any alarm settings or preset stations if they have been removed as part of the update.